Refine
Year of publication
Document Type
- Doctoral Thesis (25)
- Bachelor Thesis (1)
Language
- English (26) (remove)
Has Fulltext
- yes (26)
Is part of the Bibliography
- no (26)
Keywords
- (n, gamma) Reaktionen (1)
- (n, gamma) reactions (1)
- Activation (1)
- BaF2 Detektor-Array (1)
- BaF2 detector array (1)
- Beam dynamics (1)
- CERN PSB (1)
- Chopper (1)
- Detektor-Array (1)
- Energieauflösung (1)
The Large Hadron Collider (LHC) is the biggest and most powerful particle accelerator in the world, designed to collide two proton beams with particle momentum of 7 TeV/c each. The stored energy of 362MJ in each beam is sufficient to melt 500 kg of copper or to evaporate about 300 litre of water. An accidental release of even a small fraction of the beam energy can cause severe damage to accelerator equipment. Reliable machine protection systems are necessary to safely operate the accelerator complex. To design a machine protection system, it is essential to know the damage potential of the stored beam and the consequences in case of a failure. One (catastrophic) failure would be, if the entire beam is lost in the aperture due to a problem with the beam dumping system.
This thesis presents the simulation studies, results of a benchmarking experiment, and detailed target investigation, for this failure case. In the experiment, solid copper cylinders were irradiated with the 440GeV proton beam delivered by the Super Proton Synchrotron (SPS) at the High Radiation to Materials (HiRadMat) facility at CERN. The experiment confirmed the existence of the so-called hydrodynamic tunneling phenomenon for the first time. Detailed numerical simulations for particle-matter interaction with FLUKA, and with the two-dimensional hydrodynamic code, BIG2, were carried out. Excellent agreement was found between the experimental and the simulation results that validate predictions for the 7TeV beam of the LHC. The hydrodynamic tunneling effect is of considerable importance for the design of machine protection systems for accelerators with high stored beam energy. In addition, this thesis presents the first studies of the damage potential with beam parameters of the Future Circular Collider (FCC).
To detect beam losses due to fast failures it is essential to have fast beam instrumentation. Diamond based particle detectors are able to detect beam losses within a nanosecond time scale. Specially designed diamond detectors were used in the experiment mentioned above. Their efficiency and response has been studied for the first time over 5 orders of bunch intensity with electrons at the Beam Test Facility (BTF) at INFN, Frascati, Italy. The results of these measurements are discussed in this thesis. Furthermore an overview of the applications of diamond based particle detectors in damage experiments and for LHC operation is presented.
Cancer has become one of the most fatal diseases. The Heidelberg Heavy Ion Cancer Therapy (HICAT) has the potential to become an important and efficient treatment method because of its excellent “Bragg peak” characteristics and on-line irradiation control by the PET diagnostics. The dedicated Heidelberg Heavy Ion Cancer Therapy Project includes two ECR ion sources, a RF linear injector, a synchrotron and three treatment rooms. It will deliver 4*10 high 10 protons, or 1*10 high 10 He, or 1*10 high 9 Carbons, or 5*10 high 8 Oxygens per synchrotron cycle with the beam energy 50-430AMeV for the treatments. The RF linear injector consists of a 400AkeV RFQ and of a very compact 7AMeV IH-DTL accelerator operated at 216.816MHz. The development of the IH-DTL within the HICAT project is a great challenge with respect to the present state of the DTL art because of the following reasons: • The highest operating frequency (216.816MHz) of all IH-DTL cavities; • Extremely large cavity length to diameter ratio of about 11; • IH-DTL with three internal triplets; • The highest effective voltage gain per meter (5.5MV/m); • Very short MEBT design for the beam matching. The following achievements have been reached during the development of the IH-DTL injector for HICAT : The KONUS beam dynamics design with LORASR code fulfills the beam requirement of the HICAT synchrotron at the injection point. The simulations for the IH-DTL injector have been performed not only with a homogeneous input beam, but also with the actual particle distribution from the exit of the HICAT RFQ accelerator as delivered by the PARMTEQ code. The output longitudinal normalized emittance for 95% of all particles is 2.00AkeVns, the emittance growth is less than 24%, while the X-X’ and Y-Y’ normalized emittance are 0.77mmmrad and 0.62mmmrad, respectively. The emittance growth in X-X’ is less than 18%, and the emittance growth in Y-Y’ is less than 5%. Based on the transverse envelopes of the transported particles, the redesign of the buncher drift tubes at the RFQ high energy end has been made to get a higher transit time factor for this novel RFQ internal buncher. An optimized effective buncher gap voltage of 45.4KV has been calculated to deliver a minimized longitudinal beam emittance, while the influence of the effective buncher voltage on the transverse emittance can be neglected. Six different tuning concepts were investigated in detail while tuning the 1:2 scaled HICAT IH model cavity. ‘Volume Tuning’ by a variation of the cavity cross sectional area can compensate the unbalanced capacitance distribution in case of an extreme beta-lambda-variation along an IH cavity. ‘Additional Capacitance Plates’ or copper sheets clamped on drift tube stems are a fast way for checking the tuning sensitivity, but they will be replaced by massive copper blocks mounted on the drift tube girders finally. ‘Lens Coupling’ is an important tuning to stabilize the operation mode and to increase or decrease the coupling between neighboring sections. ‘Tube Tuning’ is the fine tuning concept and also the standard tuning method to reach the needed field distributions as well as the gap voltage distributions. ‘Undercut Tuning’ is a very sensitive tuning for the end sections and with respect to the voltage distribution balance along the structure. The different types of ‘plungers’ in the 3rd and 4th sections have different effects on the resonance frequency and on the field distribution. The different triplet stems and the geometry of the cavity end have been also investigated to reach the design field and voltage distributions. Finally, the needed uniform field distribution along the IH-DTL cavity and the corresponding effective voltage distribution were realized, the remaining maximum gap voltage difference was less than 5% for the model cavity. The several important higher order modes were also measured. The RF tuning of the IH-DTL model cavity delivers the final geometry parameters of the IH-DTL power cavity. A rectangular cavity cross section was adopted for the first time for this IH-DTL cavity. This eases the realization of the volume tuning concept in the 1st and 2nd sections. Lens coupling determines the final distance between the triplet and the girder. The triplets are mounted on the lower cavity half shell. The Microwave Studio simulations have been carried out not only for the HICAT model cavity, but also for the final geometry of the IH-DTL power cavity. The field distribution for the operation mode H110 fits to the model cavity measurement as well as the Higher Order Modes. The simulations prove the IH-DTL geometrical design. On the other hand, the precision of one simulation with 2.3 million mesh points for full cross section area and the CPU time more than 15hours on a DELL PC with Intel Pentium 4 of 2.4GHz and 2.096GRAM were exploited to their limit when calculating the real parameters for the two final machining iterations during production. The shunt impedance of the IH-DTL power cavity is estimated by comparison with the existing tanks to about 195.8MOmega/m, which fits to the simulation result of 200.3MOmega/m with reducing the conductivity to the 5.0*10 high 7 Omega-1m-1. The effective shunt impedance is 153 MOmega/m. The needed RF power is 755kW. The expected quality factor of the IH-DTL cavity is about 15600. The IH-DTL power cavity tuning measurements before cavity copper plating have been performed. The results are within the specifications. There is no doubt that the needed accuracy of the voltage distribution will be reached with the foreseen fine tuning concepts in the last steps.
In the framework of this thesis the intense low energy ion beam transport was investigated. Especially, the beam transport in toroidal magnetic field configurations was discussed, as it may allow the accumulation of high intensive beams in the future. One of the specific tasks is to design an injection system that can be used for the proposed low energy accumulator ring. This thesis regarding beam transport investigations is related to the larger research fields, storage rings used in accelerator physics and non-neutral plasmas. The proposal of building a storage ring with longitudinal guiding magnetic fields was made. Due to natural transversal focussing in magnetic fields it is possible to accumulate very intense charged particle beams, a subject of interest within the physics community. A simulation code (TBT) was written to describe the particle motion in curved segments. Particle in Cell techniques were utilized to simulate a multi particle dynamics. This code allows the user to generate different particle distributions as input parameter. A possibility of reading an external data file was made available so that a measured distribution can be used to compare simulation results with measured ones. A second order cloud in cell method was used to calculate charge density and in turn to solve Poisson’s equation. The circular toroidal coordinate system was used. The drift motion and gyrating motion was proved to be consistent with analytical values. Further simulations were performed to study the self field effects on beam transport. The experiments with single toroidal segments find niche in the work. The experiments were performed to compare the simulation results and gain practical experience. The toroidal segment has similar dimensions (major axis R = 1:3 m, minor axis r = 0:1 m, arc angle 30°) as for a full scale ring design. The main difference lies in the magnetic field strength. The available segments can be operated at room temperature producing 0:6T on axis maximum magnetic field, while for the storage ring design this value is in the range of 5T. The preparatory experiments consisted of building and characterization of the ion source in a first step. Along with the momentum spectrometer and emittance scanner the beam properties were studied. Low mass ion beams He+ and mixed p, H2+, H3+ beams were analyzed. The proton beam consisting of a 48% H+ fraction was extracted regularly and used for further experiments. A moderate beam energy of 10 keV was chosen as operational energy for which 3.08 mA proton beam current was measured. In the second stage, beams were transported through a solenoid and the phase space distribution was measured as a function of the magnetic field for different beam energies. The phase-space as distributions measured in a first stage were simulated backward and then again forward transported through the solenoid. The simulated results were then compared with the measured distribution. The LINTRA transport program was used. The phase-space distribution was further simulated for transport experiments in a toroidal magnetic field. The experiments with a single toroidal segment give basic results necessary to compare the results between transport code (TBT) and measurements. The optical diagnostic provides measurements which can be well compared with the simulated results. A digital camera with a magnetic shield was used to record images in jpeg file format. A subroutine was written to analyze an image file to give the intensity distribution of a given image file. The integrated profile in vertical and horizontal direction was used to calculate the vertical drift and the beam size. The simulated values were in good agreement with the measured ones. The injection system needs most care. The transport program that was used to simulate the beam in the toroid was also used to design the injection system. The injection system with its special field configurations was designed to perform experiments with room temperature segments. The main point to tackle was to smoothly bring the charged particles generated outside the trap into the acceptance of the ring. The designed system consists of two sources, one representing a ring beam and the other one the injection beam. While simulations showed a clear way, how to inject the particle beam via a well positioned solenoid and in combination with a transverse electric field element causing an ExB drift into the main ring acceptance. After construction of these injection elements it will be very important to measure the robustness of such a system with respect to the beam stability- especially of the injection channel.
The current performance of a 4π barium fluoride gamma detector consisting of 41 modules is evaluated. It will be used to measure neutron capture events in different samples that are exposed to a neutron beam that is expected to contain up to 10^7 neutrons/(cm^2 sec). The capture cross-sections acquired in this experiment will be relevant to a multitude of different areas, for example to s-process studies, or accelerator-driven systems. The detector array was re-mounted after having been moved from Karlsruhe to Frankfurt and in the course of this process, the detector modules have been checked for their current detection properties. Every module consists of a BaF2 crystal, a photomultiplier tube connected to the crystal by sillicon oil and a voltage divider to drive the PMT, so each of them is already an individual gamma detector. Using Cobalt-60 and Caesium-137 test sources the energy resolution and - more importantly - the time resolution of every module has been determined; the results are presented in this work and compared to previous data taken at the time the detector was built initially in the mid-1980s.
Studies and measurements of linear coupling and nonlinearities in hadron circular accelerators
(2006)
In this thesis a beam-based method has been developed to measure the strength and the polarity of corrector magnets (skew quadrupoles and sextupoles) in circular accelerators. The algorithm is based on the harmonic analysis (via FFT) of beam position monitor (BPM) data taken turn by turn from an accelerator in operation. It has been shown that, from the differences of the spectral line amplitudes between two consecutive BPMs, both the strength and the polarity of non-linear elements placed in between can be measured. The method has been successfully tested using existing BPM data from the SPS of CERN, since presently the SIS-18 is not equipped with the necessary hardware. The magnet strength of seven SPS extraction sextupoles was measured with a precision of about 10%. The polarities have been unambiguously measured. This method can be used to detect polarity errors and wrong power supply connections during machine commissioning, as well as for a continuous monitoring of the "nonlinearity budget" in superconducting machines. A second beam-based method has been studied for a fast measurement and correction of betatron coupling driven by skew quadrupole field errors and tilted focusing quadrupoles. Traditional methods usually require a time-consuming scan of the corrector magnets in order to minimize the coupling stop band |C|. In this thesis it has been shown how the same correction can be performed in a single machine cycle from the harmonic analysis of multi-BPM data. The method has been successfully applied to RHIC. It has been shown that the stop band |C| (also known in the American literature as Delta-Qmin) measured in a single machine cycle with the new algorithm is compatible with the value obtained by traditional methods. The measurement of the resonance phase Theta defines automatically the best corrector setting, which was found in agreement with the one obtained with a traditional scan. A third theoretical achievement is a new description of the betatron motion close to the difference resonance in presence of linear coupling. Compared to the matrix formalism the motion is parametrized as a function of the resonance driving term f1001 only (which is proven to be an observable), whereas making use of the matrix approach four parameters need to be measured. Formulae describing the exchange of RMS emittances when approaching the resonances have been already derived in the 70s in the smooth approximation. New formulae have been derived here making use of Lie algebra providing a better description of the emittance behavior. The emittance exchange curves are predicted by new formulae with excellent agreement with multi-particle simulations and the counter-intuitive emittance variation along the ring of the emittance is proven to be related to the variation of f1001. A new way to decouple the equations of motion and explicit expressions for the individual single particle invariants have been found. For the first time emittance exchange studies have been carried out in the SIS-18 of GSI. Transverse RMS emittances have been measured during 2005 from rest gas monitor (RGM) data. Crossing the linear coupling resonance, the transverse emittances exchange completely. It has been observed that this effect is reversible. Applications of this manipulation are: emittance equilibration under consideration for future operations of the SIS-18 as booster for the SIS-100; emittance transfer during multi-turn injection to improve the eficiency and to protect the injection septum in high intensity operations, by shifting part of the horizontal emittance into the vertical plane. The emittance exchange curves obtained experimentally have been compared with analytic formulae providing a fast measurement (in few machine cycles only) of the linear coupling stop band |C|. Technical problems prevented the use of the eight skew quadrupoles installed in the SIS-18 to compensate the linear coupling resonance. It has been observed that the emittance exchange curve is highly sensitive to the beam intensity. Multi-particle simulations with 2D PIC space-charge solver have been run to infer heuristic scaling laws able to quantify the observable stop band, to be used for the resonance compensation. The analysis of BPM and RGM data has been performed making use of new software applications developed for this purpose. The bpm2rdt code for the harmonic analysis of BPM data has been written and tested with real data. The software reads the BPM turn-by-turn data and the Twiss parameters. Then it performs the FFT of these data, finds the peaks of the Fourier spectra and infers the RDT fjklm, the strengths ^hjklm and the local terms lambda-jklm. All these observables are printed out together with the corresponding values of the model, computed from the nominal values of strengths and the Twiss parameters. From the FFT of dual-plane BPM data the linear optics (beta functions and phase advances Delta phi) at the corresponding location is also inferred. From the measurement of f1000, the linear coupling coeffcient C (amplitude and phase) is also computed. The code has been tested by using existing SPS data and new RHIC data. For the on-line analysis of RGM data the rgm2emitt code has been written. The application reads in input the raw data files from the RGM and the beam loss monitor (BLM) respectively, the latter created by the RGM on-line software itself. From the RGM data the transverse beam sizes and emittances are inferred and used together with the BLM data to compute the tune shift during the machine cycle.
For the transport of high-intensity hadron beams in low-energy beam lines of linear accelerators, the compensation of space charge forces by the accumulation of particles of opposite charge is an important effect, reducing the required focusing strength and potentially the emittance growth due to space charge forces. In this thesis, space charge compensation was studied by including the secondary particles in particle-in-cell simulations.
For this purpose, a new electrostatic particle-in-cell code named bender was developed. The software was tested using known self-consistent solutions for an electron plasma confined in an external potential as well as for a KV distributed beam in a periodic focusing lattice. For the simulation of compensation, models for residual gas ionisation by proton and electron impact were implemented.
The compensation process was studied for a 120 keV, 100 mA proton beam transported through a short drift section. Various features in the particle distributions were identified, which can not explained by a uniform reduction in the electric field of the beam. These were tied to the presence of thermal electrons confined within the beam potential. Using the Poisson-Boltzmann equation, their distribution could be reproduced and their influence on the beam for a wider range of parameters studied. However, the observed temperatures show a significant numerical influence. The hypothesis was formed, that stochastical heating present in particle-in-cell simulations is the mechanism leading to the formation of the observed (partial) thermal equilibrium.
For the low-energy beam transport line of the Frankfurt neutron source FRANZ, bender was used to predict the pulse shaping in the novel ExB chopper system. The code was also used for the design and the study of an electron lens for the Integrable Optics Test Accelerator at Fermi National Accelerator Laboratory. Aberrations due to guiding center drifts and the strong electric field of the electron beam as well as the current limits in such a system were investigated.
This thesis is structured into 7 chapters:
• Chapter 2 gives an overview of the ultrashort high intensity laser interaction with matter. The laser interaction with an induced plasma is described, starting from the kinematics of single electron motion, followed by collective electron effects and the ponderamotive motion in the laser focus and the plasma transparency for the laser beam. The three different mechanisms prepared to accelerate and propagate electrons through matter are discussed. The following indirect acceleration of protons is explained by the Target Normal Sheath Acceleration (TNSA) mechanism. Finally some possible applications of laser accelerated protons are explained briefly.
• Chapter 3 deals with the modeling of geometry and field mapping of magnetic lens. Initial proton and electron distributions, fitted to PHELIX measured data are generated, a brief description of employed codes and used techniques in simulation is given, and the aberrations at the solenoid focal spot is studied.
• Chapter 4 presents a simulation study for suggested corrections to optimize the proton beam as a later beam source. Two tools have been employed in these suggested corrections, an aperture placed at the solenoid focal spot as energy selection tool, and a scattering foil placed in the proton beam to smooth the radial energy beam profile correlation at the focal spot due to chromatic aberrations. Another suggested correction has been investigated, to optimize the beam radius at the focal spot by lens geometry controlling.
• Chapter 5 presents a simulation study for the de-neutralization problem in TNSA caused by the fringing fields of pulsed magnetic solenoid and quadrupole. In this simulation, we followed an electrostatic model, wherethe evolution of both, self and mutual fields through the pulsed magnetic solenoid could be found, which is not the case in the quadrupole and only the growth of self fields could be found. The field mapping of magnetic elements is generated by the Matlab program, while the TraceWin code is employed to study the tracking through magnetic elements.
• Chapter 6 describes the PHELIX laser parameters at GSI with chirp pulse amplification technique (CPA), and Gafchromic Radiochromic film RCF) as a spatial energy resolver film detector. The results of experiments with laser proton acceleration, which were performed in two experimental areas at GSI (Z6 area and PHELIX Laser Hall (PLH)), are presented in section 6.3.
• Chapter 7 includes the main results of this work, conclusions and gives a perspective for future experimental activities.
Precise tune determination and split beam emittance reconstruction at the CERN PS synchrotron
(2023)
In accelerator physics, the need to improve the performance and better control the operating point of an accelerator has become, year after year, an increasingly important need in order to achieve higher energies and brightness, as well as point-like particle beams. If this involves increasingly advanced technological developments (in terms, for example, of materials for more intense superconducting magnets), it can not take place in the absence of targeted studies of linear and non-linear beam dynamics. In the context of this Ph.D. thesis in physics, linear and non-linear dynamics of charged particles in circular accelerators is the topic that will be discussed and treated in detail. In particular, the presentation and discussion of the results will be divided in two main topics: the need to know the physical properties of a proton beam; and the development of innovative methods to determine and study the accelerator’s working point. With regard to the first topic, an innovative procedure will be presented to determine the transverse size of the PS beam in the beam extraction phase. Among the different ways the extraction occurs at the PS, the analysed one is based on the transverse splitting of the beam by means of non-linear fields. Thus, the knowledge of the transverse beam size is not trivial since resonant linear and non-linear beam structures (namely, core and islands) arise and, for each of them, the beam size has to be quantified. This parameter is crucial for two main reasons: the accelerator that will receive the beam exiting the upstream accelerator may have restrictions (physical or magnetic) that involve a partial or total loss of the incoming beam; and any experiments located downstream of the considered accelerator may need a beam with a transversal size as constant as possible; consequently, its monitoring and control are essential. The second topic concerns the accurate determination of the working point of an accelerator, defined as the number of transverse oscillations the particle beam travels per unit of accelerator circumference, both horizontally and vertically. This quantity is called horizontal and vertical tune, respectively. Their knowledge is also crucial to understand whether the beam will be stable or unstable. In fact, not all tune values are acceptable, as there are particular values that bring the beam into resonance. In this configuration, the amplitude of the transverse oscillations of the particles increases in an uncontrolled manner and leads to the loss of all or part of the beam. Note that, in particular operating conditions, the resonant conditions are sought and desired to model, in a suitable way, the transversal shape of the beam, such as the above mentioned PS extraction scheme. It is even clearer how much the determination of the machine working point is essential to determine the operating conditions of an accelerator. In this context, several methods (also taken from the field of applied mathematics) to calculate the tune will be demonstrated and tested numerically on different types of synthetic signals. At the end of this description, the use of experimental data will allow to obtain the benchmark of a new method for the direct calculation of some characteristic quantities of non-linear beam dynamics (namely, the amplitude detuning, i.e. the variation of tune as a function of intensity of the perturbation provided to the beam.
Zur effizienten Beschleunigung von Ionen wird meist nach deren Erzeugung in einer Ionenquelle ein Radio Frequenz Quadrupol verwendet. Die vorliegende Dissertation befasst sich mit Entwicklung, Bau und Messung des Prototyps eines neuartigen Leiter-RFQs, der bei 325 MHz betrieben wird. Der Leiter-RFQ verfügt über ein neuartiges mechanisches Design und versucht die Vorteile der beiden vorrangig im Betrieb befindlichen RFQ Typen, des 4-Rod und 4-Vane RFQs, zu verbinden. Die physikalischen Parameter sind der Spezifikation des RFQs für den geplanten Protonenlinac (p-Linac) am FAIR-Projekt an der GSI Darmstadt entnommen. Darüber hinaus wird der aktuelle Planungs- und Simulationsstand eines modulierten Prototyps mit der vollen Länge von ca. 3,5 m zur Durchführung von Strahltests dargestellt.