Refine
Year of publication
Document Type
- Doctoral Thesis (29)
- Master's Thesis (3)
Has Fulltext
- yes (32)
Is part of the Bibliography
- no (32)
Keywords
- HADES (4)
- CBM (2)
- CBM Experiment (2)
- Control System (2)
- Dileptonen (2)
- EPICS (2)
- Schwerionenphysik (2)
- Spurselektion (2)
- dileptons (2)
- heavy ion physics (2)
Institute
- Physik (32)
Im Rahmen dieser Arbeit wurde eine JTAG-Ansteuerung für MIMOSA26-Sensoren basierend auf FPGA-Boards entwickelt. Als VHDL-Code ist die Implementierung anpassbar. Jede JTAG-Chain wird durch einen unabhängigen JTAG-Chain-Controller angesteuert, so dass sich begrenzt durch die Zahl der I/O-Leitungen und die Ressourcen die Anzahl der JTAG-Chain-Controller auf einem FPGA einstellen lässt. Die Anpassbarkeit hat sich bereits bei der Strahlzeit am CERN im November 2012 gezeigt, für die eine Version mit drei JTAG-Chain-Controllern auf einem FPGA und Ausgängen auf einem SCSI-Kabel synthetisiert wurde. Dabei wurde die Prototyp-Frontend-Elektronik Version 1 verwendet. Außerdem ist die Größe des pro Sensor verwendeten Speichers (in Zweierpotenzen) im VHDL-Code einstellbar, um auch eventuelle zukünftige Sensoren mit größeren Registern zu unterstützen.
Aus dieser Sicht sollte die Implementierung mit kleinen Anpassungen im finalen MVD verwendbar sein, es gibt jedoch wie immer noch Verbesserungsmöglichkeiten, z.B. die Verwendung eines externen Speichers. Des Weiteren fehlt noch eine grafische Benutzeroberfläche für den finalen MVD, wobei wie bei den anderen Detektoren von CBM dazu eine Steuerung basierend auf EPICS entwickelt werden sollte, um eine einheitliche Oberfläche zu erreichen.
Auf Seiten der Elektronik für ded finalen MVD gibt es noch einige offene Fragen, vor allem bei der Entwicklung der Zuleitungen für die Sensoren. Die Signale auf den Flexprint-Kabeln zeigen bereits bei kurzen JTAG-Chains ein hohes Übersprechen (Abschnitt 9.1.2), das zu hoch werden könnte, wenn man Sensor-Module mit mehr als einem Sensor (wie für den finalen MVD geplant, siehe Kapitel 3) an das bisher verwendete Chain-FPC anschließt.. Es kann jedoch auch gut sein, dass das Übersprechen gar kein Problem darstellen wird. Prinzipiell besteht die Möglichkeit, dass sich das Übersprechen z.B. durch Einfügen einer Masseschicht in Kabel und Boards reduzieren lässt, was in Simulationen gezeigt wurde (siehe Kapitel 8). Jedoch wurden in diesen Simulationen die Steckverbinder und eventuelle Fehlanpassungen der Boards vernachlässigt, weshalb nicht sicher ist, ob bzw. wie gut sich dies praktisch umsetzen lässt. In jedem Fall stellen die betrachteten Möglichkeiten, das Übersprechen zu reduzieren, einen erhöhten Aufwand dar. Daher erscheint es sinnvoll, zuerst eine konkrete Geometrie für die Elektronik des finalen MVD zu entwerfen1, und für diese zu ermitteln, ob das Übersprechen ein Problem darstellt.
Dabei stellt sich die wichtige Frage, wie viele Sensoren auf einem Sensor-Modul mit einem einlagigen Kabel in der zur Verfügung stehenden Breite angeschlossen werden können, da mindestens vier zusätzliche Datenleitungen für jeden weiteren Sensor erforderlich sind.
The Compressed Baryonic Matter (CBM) is one of the core experiments at the future Facility for Anti-proton and Ion Research (FAIR), Darmstadt, Germany. Its goal is to investigate nuclear matter characteristics at high net-baryon densities and moderate temperatures. The Silicon Tracking System (STS) is a central detector system of CBM.
It is placed inside a 1Tm magnet and operated at a temperature of about −10 °C to keep radiation-induced bulk current in the 300μm double-sided microstrip silicon sensors low. The design of the STS aims to minimize the material budget in the detector acceptance (2.5° < θ < 25°). In order to do so, the readout electronics is placed outside the active area, and the analog signals are transported via ultra-thin micro-cables. The STS comprises eight tracking stations with 876 modules. Each module is assembled on a carbon fiber ladder, which is subsequently mounted in the C-shaped aluminum frame.
The scope of the thesis focused on developing a modular control system framework that can be implemented for different sizes of experimental setups. The developed framework was used for setups that required a remote operation, like the irradiation of the powering modules for the front-end electronics (FEE), but also in laboratory-based setups where the automation and archiving were needed (thermal cycling of the STS electronics).
The low voltage powering modules will be placed in the vicinity of the experiment, therefore they will experience a total dose of up to 40mGy over the 10 years of STS lifetime.
To estimate the effects of the radiation on the low-voltage module performance, a dedicated irradiation campaign took place. It aimed at estimating the rate of radiation induced soft errors, that lead to the switch off of the FEE.
Regular power cycles of multiple front-end boards (FEBs) pose a risk to the experiment operation. Firstly, such behavior could negatively influence the physics performance but also have deteriorating effects on the hardware. It was further assessed what are the limitations of the FEBs with respect to the thermal cycling and the mechanical stress. The results served as an indication of possible failure modes of the FEB at the end of STS lifetime. Failure modes after repeated cycles and potential reasons were determined (e.g., Coefficient of Thermal Expansion (CTE) difference between the materials).
Due to the conditions inside the STS efficient temperature and humidity monitoring and control are required to avoid icing or water condensation on the electronics or silicon sensors. The most important properties of a suitable sensor candidate are resilience to the magnetic field, ionizing radiation tolerance, and fairly small size.
A general strategy for ambient parameters monitoring inside the STS was developed, and potential sensor candidates were chosen. To characterize the chosen relative humidity sensors the developed control framework was introduced. A sampling system with a ceramic sensor and Fiber Optic Sensors (FOS) were identified as reliable solutions for the distributed sensing system. Additionally, the industrial capacitive sensors will be used as a reference during the commissioning.
Two different designs of FOS were tested: a hygrometer and 5 sensors multiplexed in an array. The FOS hygrometer turned out to be a more reliable solution. One of the possible reasons for a worse performance is a relatively low distance between the subsequent sensors (15 cm) and a thicker coating. The results obtained from the time response study pointed out that the thinner coating of about 15μm should be a good compromise between the humidity sensitivity and the time response.
The implementation of the containerized-based control system framework for the mSTS is described in detail. The deployed EPICS-based framework proved to be a reliable solution and ensured the safety of the detector for almost 1.5 years. Moreover, the data related to the performance of the detector modules were analyzed and significant progress in the quality of modules was noted. Obtained data was also used to estimate the total fluence, which was based on the leakage current changes.
The developed framework provided a unique opportunity to automate and control different experimental setups which provided crucial data for the STS. Furthermore, the work underlines the importance of such a system and outlines the next steps toward the realization of a reliable Detector Control System for STS.