Refine
Year of publication
Document Type
- Doctoral Thesis (16)
- Bachelor Thesis (12)
- Master's Thesis (9)
- diplomthesis (1)
Has Fulltext
- yes (38)
Is part of the Bibliography
- no (38)
Keywords
- ALICE (4)
- heavy-ion physics (2)
- ALICE upgrade (1)
- ALTRO (1)
- Dielectron (1)
- GEM (1)
- HLT (1)
- Hadronenjet (1)
- Heavy-Ion Collision (1)
- High-Level Trigger (1)
Institute
- Physik (38)
During RUN3 (2021-2023) of the Large Hadron Collider, the Time Projection Chamber (TPC) of ALICE will be operated with quadruple stacks of Gas Electron Multipliers (GEMs). This technology will allow to overcome the rate limitation due to the gated operation of the Multi-Wire Proportional Chambers (MWPCs) used in RUN1 (2009-2013) and RUN2 (2015-2018).
As part of the Upgrade project, long-term irradiation tests, so called "ageing tests", have been carried out. A test setup with a detector using a quadruple stack of 10x10cm2 GEMs was built and operated in Ar-CO2 and Ne-CO2-N2 gas mixtures. The detector performance such as gas gain and energy resolution were monitored continuously. In addition, outgassing tests of materials used for the assembly process of the upgraded TPC were performed. To reach the expected dose of the GEM-based TPC, the detector was operated at much higher gains than the TPC. It was found, that the GEMs could keep their performance within the projected lifetime of the TPC. Most of the tested materials showed no negative impact on the detector. For the tested epoxy adhesive no certain conclusion could be drawn.
At much higher doses than expected for the upgraded TPC, a new phenomenon was observed, which changed the hole geometry of the GEMs and led to a degradation of the energy resolution. Even though its occurrence is not expected during the lifetime of the GEM-based TPC, simulations were carried out to study this effect more systematically. The simulations confirmed, that a change of the hole geometries of the GEMs, lead to an increase of the local gain variation, which results in a decrease of the energy resolution.
Furthermore the effect of methane as quench gas on GEMs was studied, even though this gas is not foreseen to be used in the TPC. From ageing tests with single-wire proportional counters it is well known that hydrocarbons are produced in the plasma of the avalanches, which cover the electrodes and lead to a degradation of the detector performance. Even though GEMs have a quite different geometry, the ageing tests showed, that also this technology tends to methane-induced ageing. A loss of gas gain as well as a degradation of the energy resolution due to deposits on the electrodes was monitored. A qualitative and quantitative comparison between ageing in GEMs and proportional counters was performed.
Zunächst sind einige Methoden und Techniken zusammenfassend aufzuzählen, welche mir in meiner Zeit am IKF nahegebracht wurden.
Von technischer Seite her sind hier der Umgang mit der Instituts-eigenen Lichtmikroskop und den pA-Messgeräten sowie der analogen Messkette zu nennen. Außerdem gegebenen GEM-Folien auf Fehlstellen zu untersuchen, sie unter Spannung zu testen und anschließen in die Testkammer zu montieren und diese anschließend ordnungsgemäß in Betrieb zu nehmen. Während des Betriebs der Kammer sind neben den Messungen selbst auch die Programmierung in C++ um ein vorhandenes GUI zu verstehen und erweitern zu können zu nennen. In der Analyse der gewonnenen Daten ist vor allem die im Institut verbreiteten Analyse-Software „Root“ zu nennen um Daten zu verarbeiten, zu plotten und zu fitten.
Der physikalische Gehalt der Messungen war in Folge der ersten Messung nicht mit Sicherheit zu bestimmen, da die Raten-Abhängigkeit des IB entweder grundlegender physikalischer oder technischer Natur sein konnte, was näher zu untersuchen blieb. Nach wiederholter Messung mit größerem Messbereich und einer zweiten Messreihe mit einer anderen Gas-Mischung konnten jedoch Aussagen getroffen werden.
So konnte in der Argon-Messung die gleiche Raten-Abhängigkeit des IBF wie zuvor festgestellt werden, während der IBF in der Neon-Mischung kaum merklich anstieg. Außerdem ist festzuhalten, dass Messungen an der Kathode nur über 10 pA problemlos genau sind. Darunter werden die Werte bei zu wenig Messzeit weniger aussagekräftig.
Ziel der Bachelorarbeit war es, einen Versuch für das Fortgeschrittenen-Praktikum des Instituts für Kernphysik zu konzipieren, der es ermöglicht, die Lebensdauer von aus der kosmischen Strahlung entstandenen Myonen zu bestimmen.
Dazu wurden vorhandene Komponenten auf ihre Gebrauchstauglichkeit getestet und untersucht, insbesondere in Bezug auf die Größe der Szintillatoren, ob der für einen Praktikumsversuch zeitlich gegebene Rahmen eingehalten werden kann.
Es ergaben sich einige mechanische Probleme, insbesondere bei der Verbindung der neuen, größeren Szintillatoren mit den Photomultipliern, die angegangen wurden. Die zuerst getestete Methode stellte sich jedoch als uneffektiv heraus, sodass die endgültige Lösung mit Hilfe einer neuen, computergesteuerten Fräsmaschine der Feinmechanik-Werkstatt erreicht werden soll.
Um die entstandenen Daten zu verarbeiten, wurde ein entsprechendes Programm in LabVIEW entwickelt, das die am TDC abgegriffenen Daten auf ihre Relevanz untersucht und die Ergebnisse in eine Textdatei schreibt. Das LabVIEW Front Panel wurde dabei so gestaltet, dass es den Praktikanten alle wichtigen Daten in graphisch anschaulicher Weise liefert.
Die Daten aus der Textdatei werden dann mit Hilfe eines ROOT Makros mit zwei verschiedenen Exponentialfunktionen gefittet.
In ersten Messungen ergibt sich ein Wert für die Lebensdauer der Myonen, der erstaunlich nahe am Literaturwert liegt.
Nuclear matter, that takes the form of protons and neutrons under normal conditions, is subject to a phase transition at high temperatures and densities, liberating the quarks and gluons that are usually confined in nucleons and creating a medium of free partons: the Quark-Gluon-Plasma. It is generally believed that this state of matter can be created in relativistic collisions of heavy nuclei. The study of the medium created in these collisions is the subject of heavy-ion physics. One topic within this field are particles with high transverse momentum, that are created in initial hard collisions between partons of the incoming nuclei. The energetic partons lose energy due to interactions with the medium before they fragment into a jet of hadrons. Due to momentum conservation, these jets are usually created as back-to-back pairs, or less commonly as three-jet or photon-jet events, where a single jet is balanced by a hard photon. The energy loss can be measured using correlations between particles with high transverse momenta. A trigger particle is selected with very high transversemomentum and the distribution of the azimuthal angle of associated particles in the same event is studied, relative to the azimuth of the trigger particle.These azimuthal correlations show a peak for opening angles around 0 from particles selected from the same jet, and a second peak at opening angles around 180 degrees from back-to-back di-jets. Random combinations with the underlying event generate a flat background, extending over the full range of opening angles. The STAR experiment observed a modification of these correlations in central Au+Au collisions, where trigger particles with 4GeV < pT(trigger) < 6GeV and associated particles with 2GeV < pT(trigger) < 4GeV were selected. A strong suppression has been observed for away-side correlations in central Au+Au collisions, relative to p+p, d+Au and peripheral Au+Au data. This can be explained by assuming two partons going in opposite directions, where at least one has to travel a large distance through the medium, causing energy loss and effectively removing the event from the analysis. For near-side correlations, no significant modification has been observed, which can be explained by surface emission, assuming that the observed jets have travelled only a short distance in themedium, not leaving enough time for interactions with the medium. Both trigger- and associated particles in a correlation analysis with charged hadrons are subject to modifications due to the medium. This can be avoided by using photon-jet events instead of di-jets, because the photon does not interact with the medium and therefore provides the best available measure of the properties of the opposite jet in the presence of the underlying event. This thesis studies azimuthal correlations between regions of high energy deposition in the electro-magnetic calorimeter as trigger- and charged tracks as associated particles. The data sample had been enriched by online event selection, allowing for the selection of trigger particles with a transverse energy of more than 10GeV and associated particles with more than 2,3 or 4 GeV. The away-side yield per trigger particle is strongly suppressed like in correlations between charged particles. The near-side yield is also reduced by about a factor two, clearly different from charged correlations. The trigger particles are a mixture of photon pairs from the decays of neutral pions and single photons, mainly from photon-jet events, with small contributions from other hadron decays and fragmentation photons. Pythia simulations predict a ratio of neutral pions to prompt photons of 3.5:1 in p+p collisions with the same cuts as in the presented analysis. Single particle suppression further reduces this ratio in central Au_Au collisions, down to about 0.8:1, indicating that the majority of trigger particles in central Au+Au collisions are prompt photons. The increasing fraction of prompt photon triggers without an accompanying jet and therefore zero associated yield reduces the average yield per trigger particle. The magnitude of the observed effect agrees well with the expectation from Pythia simulations and the assumption of a single particle suppression by a factor 4-5. An analysis of away-side correlations is more difficult, because both photon-jet and di-jet events contribute. The aim is the separation of these two contributions. As a clear separation is not possible with the available dataset, a comparison with two different scenarios is given, where a surprisingly small suppression by only a factor of about 5 is favoured for both dijet- and photon-jet-correlations. A separate measurement of both contributions will be possible by a shower-shape analysis with the EM calorimeter or a comparison with charged correlations in the same kinematic region.
Die vorliegende Arbeit beschäftigt sich mit der Charakterisierung des ALTRO Chips (ALICE TPC Readout), der ein integraler und wichtiger Bestandteil der Auslesekette des TPC (Time Projection Chamber) Detektors von ALICE (A Large Ion Collider Experiment) ist. ALICE ist ein Experiment am noch im Bau befindlichen LHC (Large Hadron Collider) am CERN mit der zentralen Ausrichtung, Schwerionenkollisionen zu untersuchen. Diese sind von besonderem Interesse, da durch sie ein experimenteller Zugriff zu dem QGP (Quark Gluon Plasma) existiert, dem einzigen vom Standardmodell vorhergesagten Phasenübergang, der unter Laborbedingungen erreichbar ist. Im Jahr 2004 wurden Messungen an einem Teststrahl am CERN PS (Proton Synchrotron) durchgeführt. Der Prototyp wurde voll mit FECs bestückt, was 5400 Kanälen entspricht und einer anderen Gasmixtur (Ne/N2/CO2 90%/5%/5%) befüllt. Für das optimale Leistungsverhalten der ALICE TPC muß der Digitalprozessor im ALTRO, bestehend aus vier Berechnungseinheiten, mit den passenden Werten konfiguriert werden. Der Datenfluss beginnt mit dem BCS1 (Baseline Correction and Subtraction 1) Modul, das systematische Störungen und die Grundlinie entfernt. Da der ALTRO kontinuierlich das anliegende Signal abtastet, entfernt es automatisch langsame Grundlinienveränderungen, die Beispielsweise durch Temperaturänderungen auftreten können. Gefolgt von dem TCF (Tail Cancellation Filter), der den Schweif des langsam fallenden, vom PASA generierten Signals entfernt. Um die nichtsystematischen Störungen der Grundlinie zu entfernen, folgt die BCS2 (Baseline Correction and Subtraction 2), die auf einer gleitenden Mittelwertsberechnung mit Ausschluß von Detektorsignalen über einen doppelten Schwellenwert basiert. Die finale Einheit für die Signalverarbeitung ist die ZSU (Zero Suppression Unit), die Meßpunkte unterhalb eines definierten Schwellwertes entfernt. Hier wird der weg beschrieben die TCF und BCS1 Parameter aus vorhandenen Detektordaten zu extrahieren. Während der Analyse der Daten von kosmischen Teilchen fiel bei Signalen mit hoher Amplitude (>700 ADC) eine zusätzliche Struktur in dem Schweif auf. Der Monitor wurde deswegen mit einem gleitenden Mittelwertfilter erweitert, worauf sich diese Struktur auch in kleineren Signalen (> 200 ADC) zeigte. Dieses Signal wird von Ionen erzeugt, die zur Kathode oder zu den Pads driften, bisher ist jedoch weder die Streuung der Elektronenlawine an der Anode, noch die Variationsbreite in den erzeugten Elektronlawinen verstanden oder gemessen worden. Eine erfolgreiche Messung, sowie Charakterisierung wird in dieser Arbeit beschrieben. Im Jahr 2005 im Sommer beginnt der Einbau der Gaskammern der TPC in ALICE, die Elektronik folgt am Ende dieses Jahres. Parallel hierzu wurde der Prototyp der TPC wieder in Betrieb genommen und im Frühling wird ein kompletter Sektor mit der Detektorelektronik ausgestattet. An diesen zwei Aufbauten wird die ALTRO Charakterisierung fortgeführt, verfeinert und komplettiert.
Da in der Run 3 Periode des CERN LHC die Kollisionsrate auf 50 kHz erhöht werden soll, muss die ALICE TPC umgebaut werden. Die Vieldrahtproportionalkammern mit Sperrgitter sollen gegen eine GEM-basierte Auslese ausgetauscht werden, um eine kontinuierliche Auslese zu ermöglichen.
Es wurde eine GEM-Testkammer, die mit drei und vier GEM-Folien betrieben werden kann, entwickelt und gebaut. GEM-Folien wurden unter dem Mikroskop auf Fehler untersucht und auf ihre Spannungsfestigkeit hin getestet sowie gerahmt und in die Kammer eingesetzt. Mit der fertigen kleinen TPC mit GEM-basierter Auslese wurden IBF und Energieauflösung gemessen. Ziel der Messungen war es, einen möglichst geringen IBF von unter 1 % zu erhalten, um so wenig wie möglich Feldverzerrungen im Driftvolumen der TPC zu erhalten, bei gleichzeitig guter Energieauflösung von mindestens 12 %, um eine gute Teilchenidentifikation in der TPC sicherzustellen.
Da standard GEM-Konfigurationen mit nur drei GEM-Folien zwar eine gute Energieauflösung, jedoch zu viel IBF aufweisen, wurden die Messungen hauptsächlich mit vier GEM-Folien durchgeführt. Es wurden zwei verschiedene Arten von GEM-Folien verwendet, Standard (S) und Large-Pitch (LP) GEM-Folien, die bei einem Großteil der Messungen in der S-LP-LP-S-Konfiguration angeordnet waren.
Es wurde festgestellt, dass sich IBF und Energieauflösung gegenläufig verhalten, bei besser werdendem IBF also die Energieauflösung schlechter wird und umgekehrt.
Es wurden zwei verschiedene Gasmischungen, Ne-CO2-N2 (90-10-5) und Ar-CO2 (90-10), untersucht. Mit Neon wurde bei einem Gain von 2000 gemessen, mit Argon nur bei einem Gain von 1000, da bei Argon die Anzahl der produzierten Elektronen pro cm etwa doppelt so groß ist.
Der IBF war mit beiden Gasmischungen etwa gleich groß. Die Energieauflösung war mit Argon jedoch aufgrund des niedrigeren Gains erheblich schlechter. Mit Ne-CO2-N2 (90-10-5) gelang es, einen Arbeitspunkt mit einer Energieauflösung von etwa 12 % und einem IBF von unter 1 % zu finden, mit Ar-CO2 (90-10) war dies jedoch nicht der Fall.
A new era in experimental nuclear physics has begun with the start-up of the Large Hadron Collider at CERN and its dedicated heavy-ion detector system ALICE. Measuring the highest energy density ever produced in nucleus-nucleus collisions, the detector has been designed to study the properties of the created hot and dense medium, assumed to be a Quark-Gluon Plasma.
Comprised of 18 high granularity sub-detectors, ALICE delivers data from a few million electronic channels of proton-proton and heavy-ion collisions.
The produced data volume can reach up to 26 GByte/s for central Pb–Pb
collisions at design luminosity of L = 1027 cm−2 s−1 , challenging not only the data storage, but also the physics analysis. A High-Level Trigger (HLT) has been built and commissioned to reduce that amount of data to a storable value prior to archiving with the means of data filtering and compression without the loss of physics information. Implemented as a large high performance compute cluster, the HLT is able to perform a full reconstruction of all events at the time of data-taking, which allows to trigger, based on the information of a complete event. Rare physics probes, with high transverse momentum, can be identified and selected to enhance the overall physics reach of the experiment.
The commissioning of the HLT is at the center of this thesis. Being deeply embedded in the ALICE data path and, therefore, interfacing all other ALICE subsystems, this commissioning imposed not only a major challenge, but also a massive coordination effort, which was completed with the first proton-proton collisions reconstructed by the HLT. Furthermore, this thesis is completed with the study and implementation of on-line high transverse momentum triggers.
The measurement of dielectrons (electron-positron pairs) allows to investigate the properties of strongly interacting matter, in particular the Quark-Gluon Plasma (QGP), which is created in relativistic heavy-ion collisions at the LHC. The evolution of the collision can be probed via dielectrons since electrons do not interact strongly and are created during all stages of the collision. One of the interests in dielectron measurements is motivated by possible modifications of the electromagnetic emission spectrum in the QGP, where pp collisions are used as a medium-free reference. The dielectron spectrum consists of contributions from various processes. In order to estimate contributions of known dielectron sources, simulations of the so-called dielectron cocktail are performed. In this thesis, dielectron cocktails in minimum bias pp collisions at p s = 7 TeV, p–Pb collisions at p sNN = 5.02 TeV and in central (0-10%) and semi-central (20-50%) Pb–Pb collisions at p sNN = 2.76 TeV at the LHC are presented.