Refine
Year of publication
Document Type
- Doctoral Thesis (14)
Language
- English (14) (remove)
Has Fulltext
- yes (14)
Is part of the Bibliography
- no (14)
Keywords
- Activation (1)
- Beschleuniger (1)
- Chopper (1)
- Coulombdissoziation (1)
- Fluka (1)
- Gabor lens (1)
- Ion Beam (1)
- Mars (1)
- Molybdän (1)
- Nukleare Astrophysik (1)
Institute
- Physik (14)
The laser-driven acceleration of protons from thin foils irradiated by hollow high-intensity laser beams in the regime of target normal sheath acceleration is reported for the first time. The use of hollow beams aims at reducing the initial emission solid angle of the TNSA source, due to a flattening of the electron sheath at the target rear side. The experiments were conducted at the PHELIX laser facility at the GSI Helmholtzzentrum für Schwerionenforschung GmbH with laser intensities in the range from 10^18 to 10^20 W/cm^2. We observed an average reduction of the half opening angle by (3.07±0.42)° or (13.2±2)% when the targets have a thickness between 12 to 14 μm. In addition, the highest proton energies were achieved with the hollow laser beam in comparison to the typical Gaussian focal spot.
The Large Hadron Collider (LHC) is the biggest and most powerful particle accelerator in the world, designed to collide two proton beams with particle momentum of 7 TeV/c each. The stored energy of 362MJ in each beam is sufficient to melt 500 kg of copper or to evaporate about 300 litre of water. An accidental release of even a small fraction of the beam energy can cause severe damage to accelerator equipment. Reliable machine protection systems are necessary to safely operate the accelerator complex. To design a machine protection system, it is essential to know the damage potential of the stored beam and the consequences in case of a failure. One (catastrophic) failure would be, if the entire beam is lost in the aperture due to a problem with the beam dumping system.
This thesis presents the simulation studies, results of a benchmarking experiment, and detailed target investigation, for this failure case. In the experiment, solid copper cylinders were irradiated with the 440GeV proton beam delivered by the Super Proton Synchrotron (SPS) at the High Radiation to Materials (HiRadMat) facility at CERN. The experiment confirmed the existence of the so-called hydrodynamic tunneling phenomenon for the first time. Detailed numerical simulations for particle-matter interaction with FLUKA, and with the two-dimensional hydrodynamic code, BIG2, were carried out. Excellent agreement was found between the experimental and the simulation results that validate predictions for the 7TeV beam of the LHC. The hydrodynamic tunneling effect is of considerable importance for the design of machine protection systems for accelerators with high stored beam energy. In addition, this thesis presents the first studies of the damage potential with beam parameters of the Future Circular Collider (FCC).
To detect beam losses due to fast failures it is essential to have fast beam instrumentation. Diamond based particle detectors are able to detect beam losses within a nanosecond time scale. Specially designed diamond detectors were used in the experiment mentioned above. Their efficiency and response has been studied for the first time over 5 orders of bunch intensity with electrons at the Beam Test Facility (BTF) at INFN, Frascati, Italy. The results of these measurements are discussed in this thesis. Furthermore an overview of the applications of diamond based particle detectors in damage experiments and for LHC operation is presented.
The elements in the universe are mainly produced by charged-particle fusion reactions and neutron-capture reactions. About 35 proton-rich isotopes, the p-nuclei, cannot be produced via neutron-induced reactions. To date, nucleosynthesis simulations of possible production sites fail to reproduce the p-nuclei abundances observed in the solar system. In particular, the origin of the light p-nuclei 92Mo, 94Mo, 96Ru and 98Ru is little understood. The nucleosynthesis simulations rely on assumptions about the seed abundance distributions, the nuclear reaction network and the astrophysical environment. This work addressed the nuclear data input.
The key reaction 94Mo(g,n) for the production ratio of the p-nuclei 92Mo and 94Mo was investigated via Coulomb dissociation at the LAND/R3B setup at GSI Helmholtzzentrum für Schwerionenforschung in Darmstadt, Germany. A beam of 94Mo with an energy of 500 AMeV was directed onto a lead target. The neutron-dissociation reactions following the Coulomb excitation by virtual photons of the electromagnetic field of the target nucleus were investigated. All particles in the incoming and outgoing channels of the reaction were identified and their kinematics were determined in a complex analysis. The systematic uncertainties were analyzed by calculating the cross sections for all possible combinations of the data selection criteria. The integral Coulomb dissociation cross section of the reaction 94Mo(g,n) was determined to be (571 +- 14 (stat) +- 46 (syst) ) mb. The result was compared to the data obtained in a real photon experiment carried out at the Saclay linear accelerator. The ratio of the integral cross sections was found to be 0.63 +- 0.07, which is lower than the expected value of about 0.8.
The nucleosynthesis of the light p-nuclei 92Mo, 94Mo, 96Ru and 98Ru was investigated in post-processing nucleosynthesis simulations within the NuGrid research platform. The impact of rate uncertainties of the most important production and destruction reactions was studied for a Supernova type II model. It could be shown that the light p-nuclei are mainly produced via neutron-dissociation reactions on heavier nuclei in the isotopic chains, and that the final abundances of these p-nuclei are determined by their main destruction reactions. The nucleosynthesis of 92Mo and 94Mo was also studied in different environments of a Supernova type Ia model. It was concluded that the maximum temperature and the duration of the high temperature phase determine the final abundances of 92Mo and 94Mo.
This dissertation presents the development of a new radio frequency quadrupole (RFQ) structure of the 4-rod type with an operating frequency of 108 MHz for the acceleration of heavy ions with mass-to-charge ratios of up to 8.5 at high duty cycles up to CW operation ("continuous wave") at the High Charge Injector (HLI) of the GSI Helmholtz Centre for Heavy Ion Research in Darmstadt.
The need to develop a completely new RFQ for the HLI arises from the fact that with the previously designed and built 4-rod RFQ structure, which was commissioned at the HLI in 2010 as part of the planned HLI upgrade program, the desired operating modes in both pulsed and CW operation could not be achieved even after several years of operating experience and considerable efforts to eliminate or at least mitigate the severe operational instabilities. Mechanical vibrations of the electrodes, which result in strong modulated power reflection, as well as the high thermal sensitivity proved to be particularly problematic.
In addition to the RF design of the new RFQ by simulations performed with the CST Microwave Studio software, the focus of the investigations fell on the mechanical analysis of vibrations on the electrode rods caused by RF operation, for which the ANSYS Workbench software was used. Due to the high thermal load of the RFQ structure of more than 30 kW/m in CW operation, an accurate analysis of the thermal effects on electrode deformation as well as resulting frequency detuning of the resonator is also required, which was investigated by simulations within the capabilities of CST Mphysics Studio.
Based on the results of the design studies carried out by simulations and the thereby achieved design optimizations, a 4-rod RFQ prototype with 6 stems was finally manufactured, on which most of the properties expected from the simulations could be validated by measurements of the RF characteristics as well as of the vibration behavior.
Finally, based on the results of the pre-tests and considering a newly developed beam dynamics concept, a completely revised RF design for a new full-length HLI-RFQ was derived from the prototype design.
The first part of this work addresses the automatic online tuning of transfer lines in particle accelerator facilities. In the second part the focus lies on the automatic construction and optimisation of such transport lines. It can be shown that genetic algorithms can be used very well for optimisation in both cases. Automatic online tuning can be performed very efficiently at accelerators under certain boundary conditions and is particularly well suited for initial beam commissioning with low intensity pilot beams. The construction of transfer lines can also be formulated and solved as an minimisation problem with an adopted parameterisation. Thereby, both the imaging properties of the beam transport and the robustness against error studies can be optimised at the same time.
Studies on the focusing performance of a Gabor lens depending on nonneutral plasma properties
(2013)
The concept of the Gabor lens goes back to an idea by Dennis Gabor, who proposed a magnetron-type trap as an effective diverging lens for electron beams (collecting lens for positive ion beams).
Electrons confined inside the lens volume by orthogonal magnetic and electric fields, create an electric space charge field that causes a radial symmetric focusing force on an ion beam passing through the lens volume.
Since the beginning of the 1990s, a new design of this lens type as well as numerical models to describe the confined plasma cloud have been developed at the Institute for Applied Physics (IAP, Johann Wolfgang Goethe-University Frankfurt).
Thanks to an improved understanding of the plasma confinement as a function of the external fields, two lenses have successfully been tested for low beam currents and remain in operation.
In the scope of this work, the performance of a prototype Gabor lens for the transport of intense, i.e. space charge dominated ion beams, was investigated at the High Current Test Injector (HOSTI) of GSI Helmholtzzentrum für Schwerionenforschung GmbH for the first time.
To ensure an optimal focusing performance of the Gabor lens a homogeneous and stable electron confinement is required. Therefore, new non-interceptive diagnostic methods were developed to investigate the parameters and state of the confined nonneutral plasma column as a function of the external fields.
An essential part of the studies was the time-resolved diagnostic of an occurring plasma instability and the determination of the electron temperature via optical spectroscopy. The latter necessitated the detailed investigation of atomic excitation as well as the measurement of optical-emission cross sections.
A comparison of the results from both experiments i.e. the beam transport measurements at GSI and the diagnostic experiments performed at IAP concerning the plasma state, gave first indications of possible interaction processes between the nonneutral plasma and the ion beam.
With the increasing energies and intensities of heavy-ion accelerator facilities, the problem of an excessive activation of the accelerator components caused by beam losses becomes more and more important. Numerical experiments using Monte Carlo transport codes are performed in order to assess the levels of activation. The heavy-ion versions of the codes were released approximately a decade ago, therefore the verification is needed to be sure that they give reasonable results. Present work is focused on obtaining the experimental data on activation of the targets by heavy-ion beams. Several experiments were performed at GSI Helmholtzzentrum für Schwerionenforschung. The interaction of nitrogen, argon and uranium beams with aluminum targets, as well as interaction of nitrogen and argon beams with copper targets was studied. After the irradiation of the targets by different ion beams from the SIS18 synchrotron at GSI, the γ-spectroscopy analysis was done: the γ-spectra of the residual activity were measured, the radioactive nuclides were identified, their amount and depth distribution were detected. The obtained experimental results were compared with the results of the Monte Carlo simulations using FLUKA, MARS and SHIELD. The discrepancies and agreements between experiment and simulations are pointed out. The origin of discrepancies is discussed. Obtained results allow for a better verification of the Monte Carlo transport codes, and also provide information for their further development. The necessity of the activation studies for accelerator applications is discussed. The limits of applicability of the heavy-ion beam-loss criteria were studied using the FLUKA code. FLUKA-simulations were done to determine the most preferable from the radiation protection point of view materials for use in accelerator components.
Development of the timing system for the Bunch-to-Bucket transfer between the FAIR accelerators
(2017)
The FAIR project is aiming at providing high-energy beams of ions of all elements from hydrogen to uranium, antiprotons and rare isotopes with high intensities. The existing accelerator facility of GSI and the future FAIR facility employ a variety of circular accelerators like heavy ion synchrotrons (SIS18 and SIS100) and storage rings (ESR, CRYRING, CR and HESR) for the preparation of secondary beams and experiments. Bunches are required to be transferred into rf buckets among GSI and FAIR ring accelerators for different purposes. Without the proper transfer, the beam will be subject to various beam quality deterioration and even to beam losses. Hence, the proper bunch-to-bucket (B2B) transfer between two rings is of great importance for FAIR and is the topic, which has been investigated in this thesis.
These circular accelerators of GSI and FAIR have different ratios in their circumference. For example, the circumference ratio between SIS100 and SIS18 is an integer and between SIS18 and ESR is close to an integer and between CR and HESR is far away from an integer. The ring accelerators are connected via a complicated system of beam transfer lines, targets for the secondary particle production and the high energy separators mentioned above. For FAIR, not only the primary beams are required to be transferred from one ring to another, but also the secondary beams, e.g. the antiproton or rare isotope beams produced by the antiproton (pbar) target, the fragment separator (FRS) or the superconducting fragment separator (Super-FRS). An important topic for this system of accelerators is the proper transfer of beam between the different circular accelerators. Bunches of one ring must be transferred into buckets of another ring within an upper bound time constraint (e.g. 10 ms for most FAIR use cases) and with an acceptable B2B injection center mismatch +-1 degree for most FAIR use cases). Hence, a flexible FAIR B2B transfer system is required to realize the different complex B2B transfers between the FAIR rings in the future. In the focus of the system development and of this thesis is the transfer from SIS18 to SIS100, which can be tested at GSI on the transfer from SIS18 to ESR and from ESR to CRYRING. The system is based on the existing technical basis at GSI, the low-level radio frequency (LLRF) system and the FAIR control system. It coordinates with the Machine Protection System (MPS), which protects SIS100 and subsequent accelerators and experiments from damage caused by high intensity primary beams in case of malfunctioning. Besides, it indicates the beam status and the actual beam injection time for the beam instrumentation and diagnostics.
The conceptual realization of the FAIR B2B transfer system was introduced in this thesis for the first time. It achieves the most FAIR B2B transfers with a tolerable B2B injection center mismatch (e.g. +-1 degree) and within an upper bound time (e.g. 10 ms). It supports two synchronization methods, the phase shift and frequency beating methods. It is flexible to support the beam transfer between two rings with different ratios in their circumference and several B2B transfers running at the same time, e.g. the B2B transfer from SIS18 to SIS100 and at the same time the B2B transfer from ESR to CRYRING. It is capable to transfer beam of different ion species from one machine cycle to another and to transfer beams between two rings via the FRS, the pbar target and the Super-FRS. It allows various complex bucket filling pattern. In addition, it coordinates with the MPS system, which protects the SIS100 and subsequent accelerators or experiments from beam induced damage.
A list of criteria for the preservation of beam qualities during the rf frequency modulation of the phase shift method was analyzed. As an example the beam reaction on three different rf frequency modulation examples were analyzed for SIS18 beams. According to the beam dynamic analysis, there is a maximum value for the rf frequency modulation. The first derivative of the rf frequency modulation must be continuous and small enough and the second derivative must be small enough.
In addition to the analysis from the viewpoint of beam dynamics, two test setups were built. The first test setup was used to characterize the FAIR timing network – white rabbit network for the B2B transfer. In the second test setup, the firmware of the FAIR B2B transfer system was evaluated, which was running on the soft CPU, LatticeMico32, of the Scalable Control Unit - the FAIR standard Front End Controller. Besides, the boundary conditions of the different trigger scenarios of the SIS18 extraction and SIS100 injection kicker magnets were investigated. Finally, the application of the FAIR B2B transfer system for all FAIR use cases was demonstrated.
The dissertation plays a significant important role for the realization of the FAIR B2B transfer system and the further practical application of the system to all FAIR use cases.
In this thesis, a novel 257 kHz chopper device was numerically developed, technically designed and experimentally commissioned; a 4-solenoid, low-energy ion beam transport line was numerically investigated, installed and experimentally commissioned; and a novel massless beam-separation system was numerically developed.
The chopper combines a pulsed electric field with a static magnetic field in an ExB or Wien-filter type field configuration. Chopped beam pulses with a 257 kHz repetition rate and rise times of 110 ns were experimentally achieved using a 14 keV helium beam.
Due to the achieved results, the complete LEBT line for the future Frankfurt Neutron Source FRANZ is ready to deliver a dc or a pulsed beam. At the same time, the LEBT section represents an attractive test stand for the study of low-energy ion beams. It combines magnetic lenses, which allow space-charge compensated beam transport, and a chopper system capable of producing short beam pulses in the hundred nanosecond range. Since these beam pulses are transported onwards, their longitudinal and transverse properties can be analyzed. The pulse duration and time of flight are well below the rise time for the space-charge compensation through residual gas ionization. This opens the possibility for dedicated investigations of the transport of short, low-energy beam pulses including longitudinal and transverse space-charge effects and of relevant issues like the dynamics of space-charge compensation and electron effects in short pulses.
Design and optimization of the lattice of the superconducting synchrotron SIS300 for slow extraction
(2011)
The superconducting synchrotron SIS300 is planned to be built at the new Facility for Antiproton and Ion Research (FAIR), at GSI-Darmstadt [1]. SIS300 will be a versatile machine, which by means of a low-energy stretcher-mode or a high-energy ramped-mode will provide slowly extracted heavy ion beams towards the experimental areas. To reach the required maximum field of 4.5 T, cos(θ) magnets are necessary. Thus, SIS300 will become the first superconducting synchrotron worldwide with cos(θ) magnets providing resonant slow extraction.
Since SIS300 will be installed in the same tunnel as the SIS100 synchrotron, the dipole layout of SIS300 cannot be freely chosen. Thus, a standard lattice cannot be applied. A redesign of the SIS300 lattice accepting compromises concerning the positions and phase advances between the optical elements has been proposed. Using the analytical model of the slow extraction, firstly proposed by Kobayashi, and the analytical description of the resonance driving modes, a multiobjective optimization algorithm has been developed for the optimization of the lattice under the given boundary conditions. The final goal of the lattice optimization is a higher efficiency of the slow extraction. The results are evaluated by means of tracking simulations performed with the code Elegant.
The field quality in superconducting cos(θ) magnets is determined by the positions of the superconducting cable and the static and time-dependent effects of the current in the cable. Furthermore, the fast ramp rates of 1 T/s in the dipoles, which are fifty times faster than in any other superconducting cos(θ) magnet, together with the fact that the aperture is smaller than in conventional accelerator magnets, makes it extremely difficult to obtain a high-quality magnetic field. The unavoidable field errors affect the beam dynamics and worsen the slow extraction efficiency. Therefore, the field errors in the SIS300 dipoles have been estimated, and their effects have been taken into account in the optimization algorithm. As a result a compensation scheme has been proposed, in which time-dependent gradients in the sextupoles counteract the decay of the sextupole field errors in the dipole magnets during the slow extraction. For the limits where the compensation was no longer possible, tolerances to the magnet field errors have been determined.