Refine
Document Type
- Conference Proceeding (2)
- Doctoral Thesis (1)
Language
- English (3)
Has Fulltext
- yes (3)
Is part of the Bibliography
- no (3)
Institute
- Physik (3)
This work is focused on the anomalous skin effect in copper and how it affects the efficiency of copper-cavities in the temperature range 40-50 K. The quality factor Q of three coaxial cavities was measured over the temperature range from 10 K to room temperature in the experiment. The three coaxial cavities have the same structure, but different lengths, which correspond to resonant frequencies: around 100 MHz, 220 MHz and 340 MHz. Furthermore, the effects of copper-plating and additional baking in the vacuum oven on the quality factor Q are studied in the experiment. The motivation is to check the feasibility of an efficient, pulsed, ion linac, operated at cryogenic temperatures.
A synchrotron is a particular type of cyclic particle accelerator and the first accelerator concept to enable the construction of large-scale facilities [10], such as the largest particle accelerator in the world, the 27-kilometre-circumference Large Hadron Collider (LHC) by CERN near Geneva, Switzerland, the European Synchrotron Radiation Facility (ESRF) in Grenoble, France for the synchrotron radiation, the superconducting, heavy ion synchrotron SIS100 under construction for the FAIR facility at GSI, Darmstadt, Germany and so on. Unlike a cyclotron, which can accelerate particles starting at low kinetic energy, a synchrotron needs a pre-acceleration facility to accelerate particles to an appropriate initial value before synchrotron injection. A pre-acceleration can be realized by a chain of other accelerator structures like a linac, a microtron in case of electrons, for example, Proton and ion injectors Linac 4 and Linac 3 for the LHC, UNLAC as the injector for the SIS18 in GSI and in future the SIS18 as injector for the SIS100. The linac is a commonly used injector for the ion synchrotron and consists of some key components. The three main parts of a linac are: An ion source creating the particles, a buncher system or an RFQ followed by the main drift tube accelerator DTL. In order to meet the energy and the beam current requirement of a synchrotron injector linac, its cost is a remarkable percentage of the total facility costs.
However, the normal conducting linac operation at cryogenic temperatures can be a promising solution in improving the efficiency and reducing the costs of a linac. Synchrotron injectors operate at very low duty factor with beam pulse lengths in 1 micros to 100 micros range, as most of the time is needed to perform the synchrotron cycle. Superconducting linacs are not convenient, as they cannot efficiently operate at low duty factor and high beam currents.
The cryogenic operation of ion linacs is discussed and investigated at IAP in Frankfurt since around 2012 [1, 37]. The motivation was to develop very compact synchrotron injectors at reduced overall linac costs per MV of acceleration voltage. As the needed beam currents for new facilities are increasing as well, the new technology will also allow an efficient realization of higher injector linac energies, which is needed in that case. Operating normal conducting structures at cryogenic temperature exploits the significantly higher conductivity of copper at temperatures of liquid nitrogen and below. On the other hand, the anomalous skin effect reduces the gain in shunt impedance quite a bit[25, 31, 9]. Some intense studies and experiments were performed recently, which are encouraging with respect to increased field levels at linac operation temperatures between 30 K and 70 K [17, 24, 4, 23, 5, 8]. While these studies are motivated by applications in electron acceleration at GHz-frequencies, the aim of this paper is to find applications in the 100 to 700 MHz range, typical for proton and ion acceleration. At these frequencies, a higher impact in saving RF power is expected due to the larger skin depth, which is proportional to the frequency to the power of negative half with respect to the normal skin effect. On the other hand, it is assumed that the improvement in maximum surface field levels will be similar to what was demonstrated already for electron accelerator cavities. This should allow to find a good compromise between reduced RF power needs for achieving a given accelerator voltage and a reduced total linac length to save building costs.
A very important point is the temperature stability of the cavity surface during the RF pulse. This is of increasing importance the lower the operating temperature is chosen: the temperature dependence of the electric conductivity in copper gets rather strong below 80 K, as long as the RRR - value of the copper is adequate. It is very clear, that this technology is suited for low duty cycle operated cavities only - with RF pulse lengths below one millisecond. At longer pulses the cavity surface will be heated within the pulse to temperatures, where the conductivity advantage is reduced substantially. These conditions fit very well to synchrotron injectors or to pulsed beam power applications.
H – Mode structures of the IH – and of the CH – type are well-known to have rather small cavity diameters at a given operating frequency. Moreover, they can achieve effective acceleration voltage gains above 10 MV/m even at low beam energies, and already at room temperature operation[29]. With the new techniques of 3d – printing of stainless steel and copper components one can reduce cavity sizes even further – making the realization of complex cooling channels much easier.
Another topic are copper components in superconducting cavities – like power couplers. It is of great importance to know exactly the thermal losses at these surfaces, which can’t be cooled efficiently in an easy way.
Based on the positive results of the 0.63 m unmodulated 325 MHz Ladder-RFQ prototype from 2013 to 2016 [1, 2], a modulated 3.3m Ladder-RFQ (s. Fig. 1) has been designed and built for the acceleration of up to 100 mA protons from 95 keV to 3.0 MeV at the FAIR p-Linac [3, 4]. In this paper, we will show the results of manufacturing as well as low level RF measurements of the Ladder-RFQ including flatness and frequency tuning.