Refine
Year of publication
- 2022 (25) (remove)
Document Type
- Doctoral Thesis (25) (remove)
Has Fulltext
- yes (25)
Is part of the Bibliography
- no (25)
Keywords
- HADES (2)
- Accelerator (1)
- Activation experiment (1)
- Auditory cortex (1)
- Binary (1)
- Black hole (1)
- CBM (1)
- CPS (1)
- Cross section (1)
- Flow (1)
Institute
- Physik (25) (remove)
Sensors for high rate charge particle tracking have to withstand the harsh radiation doses deposited by the particles to be sensed. This holds particularly for the novel CMOS Monolithic Active Pixel Sensors, which are considered a promising sensor technology for future vertex detectors due to their very light material budget and excellent spatial resolution. To resist the radiation doses expected close to the interaction regions of heavy-ion experiments, the sensors have to be hardened against radiation doses, which exceed the native tolerance of CMOS technology significantly. In this thesis, the results of non-ionizing radiation hardness studies at the IKF on sensor prototypes developed at the IPHC in Strasbourg are presented. Our results demonstrate that the CMOS sensors evaluated in the context of this thesis can withstand non-ionizing radiation of up to 5×10^14 neq/cm^2. This hardness qualifies them as promising candidates for use in future vertex detectors.
The stellar nucleosynthesis of elements heavier than iron can primarily be attributed to neutron capture reactions in the s and r process. While the s process is considered to be well understood with regards to the stellar sites, phases and conditions where it occurs, nucleosynthesis networks still need accurate neutron capture cross sections
with low uncertainties as input parameters. Their quantitative outputs for the isotopic abundances produced in the s process, coupled with the observable solar abundances, can be used to indirectly infer the expected r process abundances. The two stable gallium isotopes, 69Ga and 71Ga, have been shown in sensitivity studies to have considerable impact on the weak s process in massive stars. The available experimental data, mostly derived from neutron activation measurements for quasi-stellar neutron spectra at kBT = 25 keV, show disagreements up to a factor of three.
Determining the differential neutron capture cross section can provide input data for the whole range of astrophysically relevant energies. To that end, a neutron time of flight experimental campaign at the n_TOF facility at CERN was performed for three months, using isotopically enriched samples of both isotopes. The data taken at the EAR1 experimental area covered a wide neutron energy range from thermal to several hundred keV. The respective differential and spectrum averaged neutron capture cross sections for 69Ga and 71Ga were determined in this thesis. They show good agreement with the evaluated cross sections for 71Ga, but reproduce the deviations from the evaluated data that other, more recent activation measurements showed for 69Ga.
Die Entstehung der Elemente im Universum wird auf eine Vielzahl von Prozessen zurückgeführt, die sowohl in Urknall - als auch in stellaren Szenarien angesiedelt werden. Die Kenntnis der dort ablaufenden Reaktionen und deren Raten ermöglicht es die zugrundeliegenden Modelle einzugrenzen und somit genauere Aussagen über die Plausibilität der Szenarien zu treffen. Ein Teil dieser Prozesse stützt sich auf Neutroneneinfänge an Atomkernen, wodurch die Massezahl des Ausgangskerns erhöht wird.
Die Aktivierungsmethode ermöglicht die Bestimmung der Wahrscheinlichkeit eines Neutroneneinfangs, sofern der Zielkern eine detektierbare Radioaktivität aufweist. Die experimentelle Untersuchung einer Reaktion mit einem kurzlebigen Produktkern ist eine besondere Herausforderung, da bei langen Aktivierungen zwar viele Einfänge stattfinden, die meisten Produktkerne jedoch schon während der Aktivierung zerfallen. Ein probates Mittel um genügend Zerfälle des Produktkerns beobachten zu können ist die zyklische Aktivierung, wobei die Probe in mehrfachen Wiederholungen kurz bestrahlt und ausgezählt wird.
Im Rahmen dieser Arbeit wurden zwei verschiedene Anwendungen der zyklischen Aktivierung behandelt.
Eine vom Paul Scherrer Institut Villigen bereitgestellte Probe von 10Be wurde am TRIGA Reaktor der Johannes Gutenberg - Universität Mainz mit Neutronen aktiviert. Über die Cadmiumdifferenzmethode konnte der thermische und der epithermische Anteil der Neutronen separiert werden und dadurch sowohl der thermische Wirkungsquerschnitt als auch das Resonanzintegral für die Reaktion 10Be(n,γ)11Be bestimmt werden.
Am Institut für Kernphysik der Goethe Universität Frankfurt wurde mit einem Van - de - Graaff - Beschleuniger über die 7Li(p,n)7Be Reaktion ein quasistellares Neutronenspektrum mit kBT ≈ 25 keV erzeugt. Für die zyklische Aktivierung von Proben wurde die Infrastruktur in Form einer automatisiert ablaufenden Vorrichtung zur Bestrahlung und Auszählung geplant und umgesetzt. In diesem Rahmen wurden die über das Spektrum gemittelten Neutroneneinfangsquerschnitte für verschiedene Reaktionen bestimmt. Für 19F(n,γ)20F konnte der Gesamteinfangsquerschnitt bestimmt werden. Für die Reaktion 45Sc(n,γ)46Sc wurde der partielle Wirkungsquerschnitt in den 142,5 keV Isomerzustand gemessen. Aus der 115In(n,γ)116In Reaktion konnten die partiellen Querschnitte in die Isomerzustände bei 289,7 keV, 127,3 keV sowie den Grundzustand bestimmt werden.
Außerdem wurde mit einer Hafniumprobe die partiellen Einfangsquerschnitte in den 1147,4 keV Isomerzustand von 178Hf und in den 375 keV Isomerzustand von 179Hf gemessen.
Single-electron transport in focused electron beam induced deposition (FEBID)-based nanostructures
(2022)
Mit steigender Komplexität von integrierten Schaltungen im Nanometer-Maÿstab werden immer innovativere Techniken nötig, um diese zu fabrizieren. Dies erfordert einen starken Fokus auf die Kontrolle der Fabrikation akkurater Strukturen und der Materialreinheit, und dies im Zusammenhang mit einer skalierbaren Produktion. In diesem Kontext hat Elektronenstrahlinduzierte Abscheidung (engl. Focused Electron Beam Induced Deposition, FEBID) eine wachsende Aufmerksamkeit im Bereich der Nanostrukturierung gewonnen. Der FEBID-Prozess basiert auf der lokalen Abscheidung von Material auf einem Substrat. Das Deponat entsteht durch die Spaltung von Präkursor-Molekülen durch die Interaktion mit einem Elektronenstrahl entsteht. Als Beispiel sei hier der Präkursor Me3PtCpMe angeführt. Das auf dem Substrat abgelagerte Material besteht aus wenigen Nanometer großen Kristalliten aus Platin, welche in einer Matrix aus amorphem Kohlenstoff eingebettet sind. Die Pt-C FEBID Ablagerungen sind nano-granulare Metalle, deren elektrische Transporteigenschaften die Folge des Zusammenspiels von diffusivem Transport von Ladungen innerhalb der Pt-Kristalliten und temperaturabhängigen Tunneleffekten sind. Das größte Interesse an diesen Materialien liegt an der Möglichkeit, Strukturen für technische Anwendungen im Nanometerbereich herstellen zu können.
In dieser Arbeit wurden Anwendungen, die auf Einzelelektroneneffekten beruhen, ausgewählt, um die FEBID basierte Probenpräparation zu testen. Um Einzelelektronentransport zu ermöglichen, der auf dem Tunneln einzelner Elektronen basiert, müssen alle Parameter wie Grösse und Abstände der Strukturen genauestens definiert sein. Im Rahmen dieser Arbeit wurden Einzelelektronenbausteine entwickelt, die auf zwei unterscheidlichen Anwendungen des Pt-C FEBID-Prozesses basieren. Die beiden Anwendungen sind: 1) Arrays von Gold-Nanopartikeln (Au-NP), welche mittels Pt-Strukturen kontaktiert wurden, die mit FEBID präpariert und anschlieÿend aufgereinigt wurden; 2) Einzelelektronentransistoren (engl. Single-Electron Transistors, SET), deren Inseln aus elektronennachbestrahlten Pt-C FEBID Deponate bestehen. Die elektrischen Eigenschaften der präparierten Nanostrukturen wurden charakterisiert und mit der erzielten Auflösung und Materialqualität in Relation gesetzt. Es wurden Optimierungen an der Präparationsmethode durchgeführt, welche direkt die Leitfähigkeit des Pt-C FEBID-Materials erhöhen. Dies kann durch die Änderung der
Karbonmatrix oder die Erhöhung des metallischen Gehalts der Struktur geschehen. In dieser Arbeit wurde eine katalytische Aufreinigungsmethode von Pt-C FEBID Strukturen für zwei Anwendungen genutzt: zum Einen wurden die aufgereinigten Strukturen als Keimschichten für die nachfolgende ortsgenaue Atomlagenabscheidung (engl. Area-Selective Atomic Layer
Deposition, AS-ALD) von Pt-Dünnschichten genutzt. Zum Anderen wurde diese Technik dafür genutzt, Metallbrücken zwischen den bereits durch Auftropfen zufällig auf dem Substrat aufgebrachten NP-Gruppen und den zuvor aufgebrachten UV-Lithographie (UVL) präparierten Cr-Au Kontakten zu erzeugen. Eine NP-Gruppe ist ein periodisches, granulares Array von Partikeln, welche uniform in Größe und Form sind und einen unterschiedlichen Grad von Ordnung inne haben. Durch die Art des Aufbringens kann die Anordnung der Nanopartikel durch Lösen und Erzeugen der Verbindungen beeinflusst werden. Diese Systeme zeigen ein Verhalten wie Tunnelkontakte mit Coulombblockade und eine Verteilung der Schwellspannung. Die Ergebnisse der elektrischen Messungen bestätigen den Einzelelektronentransport durch die Nanopartikel in einem typischen Elektronentransportregime mit schwacher Kopplung. Trotz dieser Ergebnisse war die Anwendung dieser Technik für die SET Nanostrukturierung nicht erfolgreich. Die Ursache
konnte zurückgeführt werden auf das Vorhandensein von Pt-Partikeln in der Nähe der Kontakte zu den Au-NP-Arrays. Die Pt-Partikel sind durch den FEBID Fertigungsprozess in
der Nähe der vorgegebenen Struktur entstanden. Aus diesem Grund wurde das FEBID Co-Deponat in der folgenden SET-Nanofabrikation entfernt.
Ein SET basiert auf einer Nano-Insel, welche durch Tunnelkontakte mit Source- und Drain-Elektroden verbunden ist. Darüber hinaus besteht eine kapazitive Verbindung zu einer
oder mehreren Gate-Elektrode(n). Innerhalb der Insel gibt es eine feste Anzahl von Elektronen.
In dieser Arbeit wurden die Source-, Drain- und Gate-Kontakte durch Ätzen mittels eines fokussierten Gallium-Strahls erzeugt, was Abstände von 50nm ermöglichte, wohingegen die SET Insel mit Pt-C FEBID-Material erzeugt wurde. Die Leitfähigkeit der Insel aus Pt-C wurde mit anschließender Elektronenbestrahlung erhöht. Als letzter Präparationsmethode wurde ein neueartiges Argon-Ätzverfahren genutzt, um die durch FEBID erzeugten Co-Ablagerungen in der direkten Umgebung der Insel zu entfernen. Durch die Elektronennachbestrhalung kann die Kopplung der einzelnen metallischen Kristalliten angepasst werden. Die Auswirkungen unterschiedlicher starker Tunnelkontakte auf die elektronischen Eigenschaften der Insel und die daraus resultierende Performanz des SETs wurden in dieser Arbeit beobachtet ...
Folgend auf den ersten Realisierungen von Bose-Einstein Kondensaten erschienen weitere innovative Experimente, die sich in den optischen Gittern gefangenen Quantengasen widmeten. In diesen zahlreichen, wissenschaftlichen Untersuchungen konnten die Eigenschaften von Bose-Einstein Kondensaten besser verstanden werden. Das Prinzip von Vielteilchensystemen, gefangen in einem periodischen Potential, bot eine Plattform zur Untersuchung weiterer Quantenphasen.
Eine konzeptionell einfache Modifikation von solchen Systemen erhält man durch die Kopplung der Grundzustände der gefangenen Teilchen an hoch angeregten Zuständen mithilfe einer externen Lichtquelle. Im Falle dessen, dass diese Zustände nahe der Ionisationsgrenze des Atoms liegen, spricht man von Rydberg-Zuständen und Atome, welche zu diesen Zuständen angeregt werden, bezeichnet man als Rydberg-Atome. Eines der vielen charakteristischen Eigenschaften von Rydberg-Atomen ist die Fähigkeit über große Entfernungen jenseits der atomaren Längenskalen zu wechselwirken. Im Rahmen von Vielteilchensystemen wurden dementsprechend Kristallstrukturen aus gefangenen Rydberg-Atomen experimentell beobachtet.
Nun stellt sich die Frage, was mit einem gefangenen Bose-Einstein Kondensat passiert, dessen Teilchen an langreichweitig wechselwirkenden Zuständen gekoppelt sind. Gibt es ein Parameterregime, in dem sowohl Kristallstruktur als auch Suprafluidität in solchen Systemen koexistieren können? Dies ist die zentrale Frage dieser Arbeit, die sich mit der Theorie von gefangenen Quantengasen gekoppelt an Rydberg-Zuständen auseinandersetzt.
The present work deals with photoionization in the realm of the absorption of one single photon. The formal treatment of one-photon ionization usually employs a semi-classical approach, where the electron’s initial and final states are described as quantum-mechanical wave functions but the photon is treated as a classical electromagnetic wave. In the calculation of photoionization cross sections with this semi-classical method, there is an often used approximation which is called the electric dipole approximation. Mathematically, the application of the dipole approximation corresponds to truncating the series expansion of an exponential after the leading term. Physically, this means neglecting the linear photon momentum and the spatial dependence of the light field. The dipole approximation is valid if the wavelength of the light is much larger than the spatial extent of the target and if the photon momentum is small compared to the momenta of the reaction products, which is generally the case for photon energies short above the electron binding energy.
For the present work, we experimentally investigated nondipolar photoionization, i.e., one-photon ionization at high photon energies where the dipole approximation breaks down. In our experiments, we irradiated single atoms and molecules with such high-energetic photons and measured the three-dimensional momentum distributions of the reaction fragments to uncover the effects of the linear photon momentum and the spatially-dependent light field on photoionization. Our observations allow the first profound insight into photoionization that reveals all photon properties, i.e., photon energy, spin, linear momentum, and the speed of light. Hopefully, our efforts make a constructive contribution to the understanding and the further exploration of light-matter interaction.
This Ph. D. thesis with the title "Characterisation of laser-driven radiation beams: Gamma-ray dosimetry and Monte Carlo simulations of optimised target geometry for record-breaking efficiency of MeV gamma-sources" is dedicated to the study of the acceleration of electrons by intense sub-picosecond laser pulses propagating in a sub-millimeter plasma with near-critical electron density (NCD) and resulting generation of the gamma bremsstrahlung and positrons in the targets of different materials and thickness.
Laser-driven particle acceleration is an area of increasing scientific interest since the recent development of short pulse, high-intensity laser systems. The interaction of intense high-energy, short-pulse lasers with solid targets leads to the production of high-energy electrons in the relativistic laser intensity regime of more than 1018 W /cm2. These electrons play the leading role in the first stage of the interaction of laser with matter, which leads to the creation of laser sources of particles and radiation. Therefore, the optimisation of the electron beam parameters in the direction of increasing the effective temperature and beam charge, together with a slight divergence, plays a decisive role, especially for further detection and characterisation of laser-driven photon and positron beams.
In the context of this work, experiments were carried out at the PHELIX laser system (Petawatt High-Energy Laser for Heavy Ion eXperiments) at GSI Helmholtz Center for Heavy-Ion Research GmbH in Darmstadt, Germany. This thesis presents a thermoluminescence dosimetry (TLD) based method for the measurement of bremsstrahlung spectra in the energy range from 30 keV to 100 MeV. The results of the TLD measurements reinforced the observed tendency towards the strong increase of the mean electron energy and number of super-ponderomotive electrons. In the case of laser interaction with long-scale NCD-plasmas, the dose caused by the gamma-radiation measured in the direction of the laser pulse propagation showed a 1000-fold increase compared to the high contrast shots onto plane foils and doses measured perpendicular to the laser propagation direction for all used combinations of targets and laser parameters.
In this thesis I present novel characterisation method using a combination of TLD measurements and Monte Carlo FLUKA simulations applicable to laser-driven beams. The thermoluminescence detector-based spectrometry method for simultaneous detection of electrons and photons from relativistic laser-induced plasmas initially developed by Behrens et al. (Behrens et al., 2003) and further applied in experiments at PHELIX laser (Horst et al., 2015) delivered good spectral information from keV energies up to some MeV, but as it was presented in (Horst et al., 2015) this method was not really suitable to resolve the content of photon spectra above 10 MeV because of the dominant presence of electrons. Therefore, I created new evaluation method of the incident electron spectra from the readings of TLDs. For this purpose, by means of MatLab programming language an unfolding algorithm was written. It was based on a sequential enumeration of matching data series of the dose values measured by the dosimeters and calculated with of FLUKA-simulations. The significant advantage of this method is the ability to obtain the spectrum of incident electrons in the low energy range from 1 keV, which is very difficult to measure reliably using traditional electron spectrometers.
The results of the evaluation of the effective temperature of super-ponderomotive electrons retrieved from the measured TLD-doses by means of the Monte-Carlo simulations demonstrated, that application of low density polymer foam layers irradiated by the relativistic sub-ps laser pulse provided a strong increase of the electron effective temperature from 1.5 - 2 MeV in the case of the relativistic laser interaction with a metallic foil up to 13 MeV for the laser shots onto the pre-ionized foam and more than 10 times higher charge carried by relativistic electrons.
The progressive simulation method of whole electron spectra described with two -temperatures Maxwellian distribution function has been developed and the results of dose simulations were compared with the acquired experimental data. The advanced feature of this method, which distinguishes it from the results of the simulation of the photon spectrum using the interaction with the target of mono-energetic electron beams (Nilgün Demir, 2013; Nilgün Demir, 2019) or the initial electron spectrum expressed as a function of one electron temperature (Fiorini, 2012), is the ability to simulate the initial electron spectrum described by the Maxwellian distribution function with two temperatures.
The important objective of this thesis was dedicated to the study and characterisation of laser-driven photon beams. In addition to this, the positron beams were evaluated. The investigation of bremsstrahlung photons and positrons spectra from high Z targets by varying the target thickness from 10 µm to 4 mm in simulated models of the interactions of electron spectra with Maxwellian distribution functions allowed to define an optimal thickness when the fluences of photons and positrons are maximal. Furthermore based on the results of FLUKA simulations the gold material was found to be the most suitable for the future experiments as e − γ target because of its highest bremsstrahlung yield.
Additionally Monte Carlo simulations were performed applying the obtained electron beam parameters from the electron acceleration process in laser-plasma interactions simulated with particle-in-cell (PIC) code for two laser energies of 20 J and 200 J. The corresponding electron spectra were imported into a Monte Carlo code FLUKA to simulate the production process of bremsstrahlung photons and positrons in Au converter. FLUKA simulations showed the record conversion of efficiency in MeV gammas can reach 10%, which reinforces the generation of positrons. The obtained results demonstrate the advantages of long-scale plasmas of near critical density (NCD) to increase the parameters of MeV particles and photon beams generated in relativistic laser-plasma interaction. The efficiency of the laser-driven generation of MeV electrons and photons by application of low-density polymer foams is essentially enhanced.
This work ties in with the investigation of the intermediate valent states and valence fluctuations in certain europium based intermetallic systems. Valence fluctuations are a property of the electronic system of a compound that is possibly accompanied by structural effects, which, in some cases, are quite noticable. By assuming how the changes in the electronic system and in the crystal lattice are connected, valence _uctuations of europium are believed to be a possible probe for the theory of quantum critical elasticity, which is investigated on by the SFB TRR 288 (Frankfurt, Mainz, Karlsruhe, Bochum, Dresden).
Here, the proceedings in growing single crystals of di_erent compounds related to this _eld of research are reported. This includes the ThCr2Si2 (122) type compounds EuPd2Si2 as well as the doping series EuPd2(Si1-xGex)2, the Europium based ternary Phosphides EuFe2P2, EuCo2P2, EuNi2P2 and EuRu2P2, and attempts to grow compounds of a derived 1144 structure by ordered substitution of half the Europium, EuKRu4P4.
The largest part of this work focusses on the EuPd2Si2 system, which exhibits intermediate valent europium and a temperature dependent transition between two di_erent intermediate valent states of europium. Crystals of this system were grown using the Czochralski method with a levitating melt and an europium excess flux after a two step prereaction process. Also, explorations of a PdSi-rich flux and external flux methods are reported. Ten Czochralski grown experiments, in six generations iteratevely seeded by the previous generation, were prepared.
Thermodynamical and structural analyses of the crystals located the transition between the di_erent intermediate valent states of europium between 140K and 165 K, transitioning from a high temperature Eu2.3+ state to a low temperature Eu2.7+ state, and classified it as a second order transition. To this transition a lattice anomaly of the a-parameter collapsing about 2% is connected, while the c-parameter remains largely unaffected. Large differences between individual samples can be explained by combining thermodynamical and structural analyses with compositional analysis, revealing the valence transition temperature as strongly dependent on the sample composition and Pd-Si site interchanges.
Searching to change the character of the valence transition to first order, silicon was substituted by germanium to introduce negative pressure. Germanium substituted samples of EuPd2(Si1-xGex)2 were grown using the Czochralski method with the optimized parameters from the growth experiments for the undoped compound. Samples were prepared with a nominal substitution of x = 0.05, x = 0.10, x = 0.15, x = 0.20 (twice) and x = 0.30. For the EuPd2(Si1-xGex)2 system, a phase diagram for the europium valence states is derived from chemical and thermodynamical characterizations.
n ternary europium phosphides EuT2P2, the position of the compounds in the generalized phase diagram and the question of long range magnetic order or valence transition appear connected to an isostructural transition of the tetragonal crystal structure, drastically decreasing the length of the c-parameter while establishing covalent bonds between phosphorus atoms of different interlayers of the structure, the so called ‚collapse‘. While EuFe2P2, EuT2P2 and EuCo2P2 display both long range magnetic order and a non-collapsed crystal structure, EuNi2P2 shows both a valence transition between two intermediate valent states at a characteristic temperature of 36K - accompanied by a small lattice anomaly of the a-parameter shrinking about 0.2% - and a collapsed crystal structure. Samples of EuFe2P2, EuCo2P2 and EuNi2P2 were grown in tin flux and using solid-solid sintering approaches.
Single crystals of EuFe2P2, EuCo2P2 and EuRu2P2 were investigated at ESRF in Grenoble with single crystal X-ray di_ractometry on a pressure range up to 15GPa and at temperatures down to 15K to investigate the nature of the structural transitions in the compounds. While in EuCo2P2 the structural transition occurs as a transition of first order at all temperatures (e.g. at 2GPa for 15 K), in EuFe2P2 and EuRu2P2 the structural collapse evolves over a broad pressure range up to 8GPa and as a transition of second order troughout the temperature ranges, albeit seeming to sharpen at lower temperatures. From the crystallographic data, elastic constants of the compounds could be derived, revealing EuFe2P2 and EuRu2P2 as unexpectedly elastic materials.
In order to probe the structural collapse at more accessible pressures, crystals with a sturcture derived from the 122 structure, but with ordered 50% substitution of europium and hence altering the symmetry from I4/mmm to P4/mmm in a 1144 structure, were exploratively pursued. Different experiments to obtain EuAT4P4 (with A = K, Rb, Cs and T = Fe, Ru) from binary or ternary prereactants or directly from the elements remained largely unsuccessful.
We study the polarization of relativistic fluids using the relativistic density operator at global and local equilibrium. In global equilibrium, a new technique to compute exact expectation values is introduced, which is used to obtain the exact polarization vector for fields of any spin. The same result has been extended to the case of massless fields. Furthermore, it is demonstrated that at local equilibrium not only the thermal vorticity but also the thermal shear contribute to the polarization vector. It is shown that assuming an isothermal local equilibrium, the new term can solve the polarization sign puzzle in heavy ion collisions.
In order to understand the origin of the elements in the universe, one must understand the nuclear reactions by which atomic nuclei are transformed. There are many different astrophysical environments that fulfill the conditions of different nucleosynthesis processes. Even though great progress has been made in recent decades in understanding the origin of the elements in the universe, some questions remain unanswered. In order to understand the processes, it is necessary to measure cross sections of the involved reactions and constrain theoretical model predictions. A variety of methods have been developed to measure nuclear reaction cross sections relevant for nuclear astrophysics. In this thesis, two different experiments and their results, both using the well-established activation method, are presented.
A measurement of the proton capture cross section on the p-nuclide 96Ru was performed at the Institute of Structure and Nuclear Astrophysics ISNAP - Notre Dame, USA. The main goal of this experiment was to compare the results with those obtained by Mei et al. in a pioneering experiment using the method of inverse kinematics at the GSI Helmholtzzentrum für Schwerionenforschung GmbH - Darmstadt, Germany. Therefore, the activations were taken out at the same center of mass energies of 9 MeV, 10 MeV and 11 MeV. Another activation was taken out at an energy of 3.2 MeV to compare the result to a measurement of Bork et al. who also used the activation method. While the results at 3.2 MeV agree quite well with those of Bork et al., the results at higher energies show significantly smaller cross sections than those measured by Mei et al.. Experimental details, the data analysis and sources of uncertainties are discussed.
The second part of this thesis describes a neutron capture cross section experiment. At the Institut für Kernphysik - Goethe Universtität Frankfurt an experimental setup allows to produce quasi maxwell-distributed neutron fields to measure maxwell-averaged cross sections (MACS) relevant for s-process nucleosynthesis. The setup was upgraded by a fast electric linear guide to transport samples from the activation to the detection site. The cyclic activation of the sample allows to increase the signal-to-noise ratio and to measure neutron captures that lead to nuclei with
half-lives on the order of seconds. In a first campaign, MACS of the reactions 51V(n,γ), 107,109Ag(n,γ) and 103Rh(n,γ) were measured. The new components of the setup aswell as the data analysis framework are described and the results of the measurements are discussed.