Refine
Year of publication
Document Type
- Doctoral Thesis (139) (remove)
Has Fulltext
- yes (139)
Is part of the Bibliography
- no (139)
Keywords
- Stratosphäre (4)
- Eiskeime (3)
- Meteorologie (3)
- Monsun (3)
- Schwerewellen (3)
- Anisotropie (2)
- BTEX (2)
- Belize (2)
- Boden (2)
- Caribbean (2)
Institute
- Geowissenschaften (139) (remove)
During this study clumped isotope analysis of carbonates was established at the Goethe University of Frankfurt, Germany. Therefore, preparation protocols and analytical parameters were elaborated to obtain precise and accurate Δ47 data. Briefly, analyte CO2 was cleaned cryogenically using glass extraction lines to remove traces of water that enable re-equilibration of C–O bonds in the gases. Furthermore, analyte CO2 was passed through a gas chromatograph (GC) to clean it from contaminants that produce isobaric interferences with m/z 47. Initially, phosphoric acid digestions of carbonates was conducted at 25 °C in McCrea-type reaction vessels. Afterwards samples were reacted at 90 °C using a common acid bath. Mass spectrometric analyses were performed using a MAT 253 equipped with a dual inlet system. Δ47 values were directly projected to the absolute scale using CO2 gases equilibrated at distinct temperatures.
In cooperation with Stefano Bernasconi and his research group at ETH Zurich we studied the non-linearity that occurs for the measurement of m/z 47. This effect results from secondary electrons created by the m/z 44 beam. These electrons cause a negative background on the m/z 47 collector. A correction procedure was proposed that relies on the determination of the negative background on the m/z 47 Faraday cup. This approach might reduce time-consuming analyses of heated gases which were used so far to account for the observed non-linearity. However, the suggested correction of the negative background on the m/z 47 cup is only applicable if the slit width of the m/z 44 beam is significantly wider than that of the m/z 47 beam.
This thesis, furthermore, presents a comparison of the different phosphoric acid digestion techniques which are commonly used for carbonate clumped isotope analysis. For calcitic and aragonitic material digested at 25 °C in McCrea-type vessels we observed that the sample size has an effect on Δ47 data: higher mean Δ47 values and a larger scatter of data were received for samples <7 mg than for larger aliquots. For carbonate samples digested at 90 °C in a common acid bath no sample size effect was determined. We assume that secondary re-equilibration of CO2 with water preferentially occurs at 25 °C producing the observed differences. However, a sample size effect can be avoided if reaction temperature is increased to 90 °C.
In order to make carbonate Δ47 data obtained from acid digestions at 90 °C comparable to Δ47 data received from reactions at 25 °C the difference of the acid fractionation factores (Δ47*25-90) between both temperatures has to be known. For the determination of the Δ47*25-90 value we have considered Δ47 data made at 25 °C from samples >7 mg only. For calicte and aragonite we obtained differences in fractionation factores of 0.075‰ and 0.066‰, respectively. These Δ47*25-90 values are coincident with the theoretical prediction of 0.069‰ proposed for calcite (Guo et al., 2009).
Moreover, this dissertation comprises a calibration study of the clumped isotope thermometer based on various natural calcites that grew between 9 and 38 °C. The samples include a brachiopod shell, a bivalve shell, an eggshell of an ostrich and foraminifera tests which formed from distinct biomineralizing processes. Furthermore we included an authigenic carbonate crystallized from biological-induced precipitation. The following linear relationship between 1/T2 and Δ47 was determined (with Δ47 in ‰ and T in K):
Δ47 = 0.0327 (± 0.0026) x 106 / T2 + 0.3030 (± 0.0308) (R2 = 0.9915)
This equation differs from the pioneering Ghosh et al. (2006a) calibration. However, our regression line is statistically indistinguishable from that of Henkes et al. (2013) which is based on aragonitic mollusks and calcitic brachiopod shells. Both studies have in common that calibration data were, at first, directly referenced to the absolute scale. In addition, both datasets rely on similar digestion techniques. Furthermore, the two calibrations are conform with the theoretical prediction of Guo et al. (2009).
The calcite calibration of the clumped isotope paleothermometer received in this study was applied to Δ47 data measured for Silurian brachiopods shells from Gotland/Sweden. Prior to isotopic analysis the fossils were intensively investigated for their preservation state (CL, SEM, trace elements). The lowest T(Δ47) values of ca. 28 to 33 °C were estimated from ultrastructurally well-preserved regions of some shells. For these samples also the lowest δ18Ow values of Silurian seawater were determined. These estimates of ca. −1‰ confirm the assumption that the δ18O value of the Silurian ocean was buffered to (0 ± 1)‰.
Nevertheless, most studied shells were characterized by a patchwork of pristine and altered shell portions resulting in elevated T(Δ47) values which plot mostly between 40 and 60 °C. Our results indicate that the clumped isotopic composition of the shells were altered at low water-rock ratios, not affecting the δ18O values. Δ47 and δ18O data of associated diagenetic phases (sparitic and micritic phases of the inner fillings of the fossils) provide evidence that the sparitic cements grew during several diagenetic events which occurred at different temperatures in fluid-buffered systems. We, furthermore, conclude that the micritic phases lithified at a very early diagenetic stage with the δ18O values being most probably close to a Silurian seawater composition
Terrestrial climate and ecosystem evolution during ‘Greenhouse Earth’ phases of the early Paleogene remain incompletely known. Particularly, paleobotanical records from high southern latitudes are giving only limited insights into the Paleocene and early Eocene vegetation of the region. Hence, data from continuous well-calibrated sequences are required to make progress with the reconstruction of terrestrial climate and ecosystem dynamics from the southern latitudes during the early Paleogene.
In order to elucidate the terrestrial conditions from the high southern latitudes during the early Paleogene, terrestrial palynology was applied in the present study to two well-dated deep-marine sediment cores located at the Australo-Antarctic region: (i) IODP Site U1356 (Wilkes Land margin, East Antarctica) and (ii) ODP Site 1172 (East Tasman Plateau, southwest Pacific Ocean). The studied sequence from IODP Site U1356 comprises mid-shelfal sediments from the early to middle Eocene (53.9 – 46 million years ago [Ma]). For the ODP Site 1172, the studied succession is characterized by sediments deposited in shallow marine environments of the middle Paleocene to the early Eocene (60.7 – 54.2 Ma).
Based on the obtained pollen and spores (sporomorphs) results from the studied sequences of Site U1356 and Site 1172, this study aims to: (1) decipher the terrestrial climate conditions along the Australo-Antarctic region from the middle Paleocene to the middle Eocene; (2) evaluate the structure, diversity and compositional patterns of forests that throve in the Australo-Antarctic region during the early Paleogene; (3) understand the response of forests from the high southern latitudes to the climate dynamics from the early Paleogene; (4) establish a connection between the generated terrestrial palynomorph data and published Sea Surface Temperatures (SSTs) from the same cores.
To decipher the terrestrial climatic conditions on the Australo-Antarctic region, this study relies on the nearest living relative (NLR) concept that assumes that fossil taxa have similar climate requirements as their modern counterparts. This approach was applied to the sporomorph results of Site U1356 and Site 1172, following mainly the bioclimatic analysis. With regard to the structure and diversity patterns of the vegetation from the same region, the present study presents combined qualitative (i.e., reconstruction of the vegetation based mainly on the habitats of the known living relatives) and quantitative (i.e., application of ordination techniques, rarefaction and diversity indices) analyses of the fossil sporomorphs results.
The overall results from the paleoclimatic and vegetation reconstruction approaches applied in the present study, indicate that temperate and paratropical forests during the early Paleogene throve under different climatic conditions on the Wilkes Land margin and on Tasmania, at paleolatitudes of ∼70°S and ∼65°S, respectively.
Specifically, the sporomorph results from Site U1356, suggest that a highly diverse forest similar to present-day forests from New Caledonia was thriving on Antarctica during the early Eocene (53.9 – 51.9 Ma). These forests were characterized by the presence of termophilous taxa that are restricted today to tropical and subtropical settings, notably Bombacoideae, Strasburgeria, Beauprea, Spathiphyllum, Anacolosa and Lygodium. In combination with MBT/CBT paleotemperature results, they provide strong evidence for near-tropical warmth at least in the coastal lowlands along the Wilkes Land margin. The coeval presence of frost tolerant taxa such as Nothofagus, Araucariaceae and Podocarpaceae during the early Eocene on the same record suggests that paratropical forests were thriving along the Wilkes Land margin. Due to the presence of this kind of vegetation, it is possible to suggest that forests in this region were subject to a climatic gradient related to differences in elevation and/or the proximity to the coastline.
By the middle Eocene, the paratropical forests that characterized the vegetation of the early Eocene on the Wilkes Land margin were replaced by low diversity temperate forests dominated by Nothofagus, and similar to present-day cool-temperate forests from New Zealand. The dominance of these forests and the absence of thermophilous elements together with the lower temperatures suggested by the MBT/CBT and the sporomorph-based temperatures indicate consistently cooler conditions during this time interval.
With regard to the sporomorph results of Site 1172, this study suggests that three vegetation types were thriving on Tasmania from the middle Paleocene to the early Eocene under different climatic conditions. During the middle to late Paleocene, warm-temperate forests dominated by Podocarpaceae and Araucariaceae were the prevailing vegetation on Tasmania. The dominance of these forests was interrupted by the transient predominance of cool-temperate forests dominated by Nothofagus and Araucariaceae across the middle/late Paleocene transition interval (~59.5 to ~59.0 Ma). This cool-temperate forest was characterized by a lack of frost-sensitive elements (i.e., palms and cycads) indicating cooler conditions with harsher winters on Tasmania during this time interval. By the early Eocene, and linked with the Paleocene Eocene Thermal Maximum (PETM), Paleocene temperate forests dominated by gymnosperms were replaced by paratropical rainforests with the remarkable presence of the tropical mangrove palm Nypa during the PETM and the earliest Eocene. The overall results from Site U1356 and Site 1172, provide a new assessment of the terrestrial climatic conditions in the Australo-Antarctic region for validating climate models and understanding the response of high-latitude terrestrial ecosystems to the climate dynamics of the early Paleogene on southern latitudes.
The climatic conditions in the higher latitudes during the early Paleogene were further unravelled by comparing the obtained terrestrial and marine results. The integration of the obtained sporomorph data with previously published TEX86-based SSTs from Site 1172 documents that the vegetation dynamics were closely linked with the temperature evolution from the Australo-Antarctic region. Moreover, the comparison of TEX86-based SSTs and sporomorph-based climatic estimations from Site 1172 suggests a warm-season bias of both calibrations of TEX86 (i.e., TEX86Hand TEX86H), when this proxy is applied to high southern latitudes records of the early Paleogene.
To reconstruct ocean circulation changes during specific periods of Earth history, benthic and planktic foraminifera were used as proxies in the different parts of this thesis. Both studied time periods, the Late Cretaceous and the early Pleistocene, are characterized by long-term climate cooling and major changes in ocean circulation. The first part of this thesis concentrated in the Late Cretaceous. During the Late Cretaceous long-term cooling phase, benthic foraminiferal δ18O values show a positive shift lasting about 1.5 Myr (71.5–70 Ma). This shift can be observed on a global scale and has become known as the Campanian-Maastrichtian Boundary Event (CMBE). It is proposed that this δ18O excursion is influenced either by changing intermediate- to deep-water circulation or by temporal build-up of Antarctic ice sheets. Benthic foraminiferal assemblage counts from a southern high-latitudinal site near Antarctica (ODP Site 690) are analyzed to test if the influence of the CMBE on the benthic species composition. One of the two discussed hypotheses for the causation of the δ18O transition is a change in intermediate- to deep-water circulation from low-latitude to high-latitude water masses. This change would result in cooler temperatures, higher oxygen concentration, and possibly lower organic-matter flux at the seafloor, causing a major benthic foraminiferal assemblage change. Another possible explanation of the δ18O transition of the CMBE is significant ice formation on Antarctica. However no major benthic foraminiferal assemblage change would be expected in this case. The benthic foraminiferal assemblage of Site 690 shows a separation of the studied succession into two parts with significantly different species composition. The older part (73.0–70.5 Ma) is dominated by species, which are typical for lower bottom water oxygen concentration and more common in low-latitude assemblages. Species dominating the younger part (70.0–68.0 Ma) are indicators for well-oxygenated bottom waters and more common in high-latitude assemblages. This change in the benthic foraminiferal assemblages is interpreted to represent a shift of low-latitude toward high-latitude dominated intermediateto deep-water sources. A change in oceanic circulation was therefore at least a major component of the CMBE. The Pacific Ocean contributed significantly to the climatic development during the Late Cretaceous cooling period. The contribution of ocean circulation changes in the Pacific Ocean to the Late Cretaceous climatic development in general and the CMBE and Mid-Maastrichtian Event (MME) in particular, however, is poorly understood. Previously measured high resolution planktic and benthic stable isotope data and a neodymium (Nd) isotope record from the Pacific ODP Site 1210 (Shatsky Rise, tropical Pacific Ocean) for the Campanian to Maastrichtian (69.5 to 72.5 Ma) are used to reconstruct changes in surface- and bottom water temperatures as well as changes in the source region of deep- to intermediate waters [see Appendix 4; Jung et al. 2013]. The results of the benthic foraminiferal δ18O and Nd isotope records in combination with Nd isotope records from other studies indicate changes in the intensity of intermediate- to deep ocean circulation in the tropical Pacific across the Campanian-Maastrichtian interval [see Appendix 4; Jung et al. 2013]. During the early Maastrichtian (72.5 to 69.5 Ma), a three-million-year-long period of cooler conditions and a simultaneous change towards less radiogenic Nd isotope signatures is interpreted to represent a period of increased admixture and northward flow of deep waters from the Southern Ocean (Southern Component Water, SCW). This change was probably caused by an intensified formation of deep waters in the Southern Ocean. This was reduced again during the MME (69.5 to 68.5 Ma). This early Maastrichtian cold interval is similar to the CMBEδ13C fall and succeeding δ13C rise towards the MME and is therefore also interpreted to represent tectonically forced, long-term changes in the global carbon cycle and thus a tectonic forcing of the early Maastrichtian climate cooling. Overall, the Campanian-Maastrichtian Nd and stable isotope records of Shatsky Rise indicate changes in ocean circulation that are paralleled by global warming and cooling periods. The fluctuating strength of SCW contribution in the tropical Pacific points towards an increased respectively weakened ocean circulation, which is probably related to the strength of deep-water formation in the Southern Ocean [see Appendix 4; Jung et al. 2013]. For this study, the analysis of benthic foraminiferal assemblages of Site 1210 is carried out for the same time interval (69.5 to 72.5 Ma) as Nd and stable isotopes to evaluate the influence of intermediate- to deep ocean circulation changes on the benthic foraminiferal community. The possible reaction of benthic foraminiferal assemblages is compared to the results of stable isotope and neodymium isotopes. The observed changes in species abundances only partly reflect the circulation changes reconstructed with Nd and stable oxygen istopes. For example, Stensioina spp., Aragonia spp. and Lenticulina spp., cold-water preferring species, start to be increasingly abundant at the beginning of enhanced influence of SCW. However, their abundance pattern does not follow the varying strength of the cold SCW influence at Shatsky Rise. Other species prefer lesser oxygen concentrations and warmer bottom water, e.g. Paralabamina spp. and Globorotalites spp. Paralabamina spp. has its highest relativ abundance at the beginning of the studied succession, where the influence of SCW is small. However, this taxa occurs throughout the record, even though the influence of SCW increases. Globorotalites spp. is even most abundance after the CMBE, where bottom waters are till cold and influenced by SCW. This leads to the conclusion that the varying strength of SCW in the tropical Pacific at Shatsky Rise through the studied interval is not facilitating a significant faunal turnover as has been observed at the South Atlantic Site 690 (Chapter 3). These results of the benthic foraminiferal assemblage analysis suggest a rather minor influence of the SCW on the major environmental factors that are generally influencing benthic foraminiferal communities (e.g., oxygen concentration, organic matter flux to the sea floor, bottom-water temperature). The second major part of this thesis focused on the late Pliocene-earliest Pleistocene. The late Pliocene is characterized by a long-term global cooling trend resulting in a major increase of Arctic ice sheets from around 3 Ma onwards, culminating in the Plio-Pleistocene intensification of the Northern Hemisphere glaciation. At around 2.7 Ma, large amplitude glacial-interglacial excursions (~1‰ δ18O in benthic foraminiferal calcite) in benthic oxygen isotopes can be observed. Marine isotope stage (MIS) 100 at around 2.55 Ma is the first glacial, when widespread ice rafted debris has been found in sediments in the North Atlantic Ocean. To gain a deeper understanding of the climatic evolution of the latest Pliocene-early Pleistocene, it is necessary to improve the reconstructions of North Atlantic paleohydrography, as the North Atlantic provides a key region for global climate. The consequences of the intensification of Northern Hemisphere on the early Pleistocene North Atlantic thermocline stratification and intermediate waters are still poorly understood. However, surface hydrography, the history of the thermocline and development of North Atlantic intermediate waters are well-studied for the Last Glacial Maximum (LGM). These well-known mechanisms responsible for the LGM in comparison with the present-day interglacial North Atlantic are used as an analogue for te early Pleistocene glacialinterglacials cycles. In this study, suborbitally resolved stable oxygen and carbon isotope and Mg/Ca records are measured from a deep-dwelling planktic foraminifera (Globorotaliacrassaformis) from Integrated Ocean Drilling Program Site U1313 (North Atlantic, 41°N) covering marine oxygen isotope stages MIS 103 to 95 (early Pleistocene, 2.6 to 2.4 Ma). The results are interpreted to represent a change in intermediate-water masses on glacialinterglacial timescales. During glacials geochemical records in G. crassaformis (~500–1000 m) bear the imprint of Glacial North Atlantic Intermediate Water (GNAIW), while during interglacials this species reflects the signature of the influence of Mediterranean Outflow Water (MOW) in combination with the subtropical gyre. The comparison of this data with the published records from G. ruber from the same samples facilitates the reconstruction of glacial-interglacial stratification changes of the upper water column at Site U1313. The results show that larger gradients of temperature, salinity and δ13C prevailed during glacials, suggesting a stronger stratification of the upper water column. This can be seen to indicate glacial-interglacial changes in ntermediate water masses in the North Atlantic similar to those reconstructed for the latest Pleistocene. As an additional proxy, the clumped isotope paleothermometer is applied for the Late Cretaceous study as well as for the early Pleistocene. This proxy is commonly assumed to be independent of other factors than temperature. Clumped isotopes are measured for the Late Cretaceous Site 690 on the planktic foraminiferal species Archaeoglobigerina australis and compared to already existing stable oxygen isotopes of this species. This is assumed to enable the reconstruction of paleotemperature independent of ice volume and therefore contribute to the long-lasting discussion whether there was a temporal ice build-up on Antarctic during the Campanian-Maastrichtian cooling period. For the early Pleistocene, the planktic foraminiferal species G. crassaformis is used from Site U1313 from MIS 99 (interglacial) and MIS 98 (glacial). This provides the opportunity to separate ice volume, salinity and temperature effects on the measured δ18O record of G. crassaformis. The results of the clumped isotope measurements reveal comparatively large standard errors. For the Late Cretaceous the standard error of the clumped isotope measurements proved too large to allow any conclusions on the temperature component on the δ18O record of A. australis. For the early Pleistocene, the temperature difference is also too small to be reconstructed with the standard error of the clumped isotope measurements in this study. Measuring many replicates of one sample would minimize the standard error considerably. However, the amount necessary to measure replicates cannot be gained for either time period, as almost all foraminifera were picked from the respective samples. It is concluded that the respective questions may be solved with a different method of clumped isotope analysis requiring less sample material. This method is, for example, available at the ETH Zurich.
Mantle convection is the process by which heat from the Earth’s core is transferred upwards to the surface and it is accepted to explain the dynamics of the Earth’s interior. On geological time-scales, mantle material flows like a viscous fluid as a consequence of the buoyancy forces arising from thermal expansion. Indeed, mantel convection provides a framework which links together the major disciplines, such as seismology, mineral physics, geochemistry tectonic and geology. The numerical model has been applied to understand the dynamic, structure and evaluation of the Earth, and other terrestrial planets and the investigations continue to explore, different aspects of the mantle convection.
In fact, to model this phenomenon, two complementary approaches are possible. On the one hand, one can solve self-consistently the equations of thermal convection, including parameters and employing physical relationships derived from mineral physics. Our understanding of mantle convection depends ultimately upon the success of such fully self-consistent dynamic models in explaining observable features of the flow. Although, these models presently unable to predict the actual convection pattern of the Earth, they are extremely useful to investigate general characteristics of given physical systems. On the other hand, to permit comparison with specific observables associated with the flow, one can consider a more restricted problem. Instead of focusing on the time evolution of mantle flow, if we know a priori the temperature - and hence presumably the density - anomalies that drive the convection, we can try to build a snapshot of the present-day flow pattern, consistent with those anomalies, that can successfully predict the observables. As matter of fact, the aim of this study is to investigate both approaches in comparison with the main geophysical constraints on mantle structure. These constraints include the geoid anomalies, the dynamic surface and core-mantle boundary topography and tectonic plate motions.
The most appropriate mathematical basis functions for describing a bounded and continuous function on a spherical surface are spherical harmonics. We may therefore expand the geodynamic observables in terms of spherical harmonics. We have investigated two methods of the global spherical harmonic analysis by specific attention to the dynamic geoid computation of the geodynamic models. The first method is the quadrature method in which the loss of the orthogonality of the Legendre functions in transition from continues to discrete case is the major drawback to the method. Particularly, we showed that in the absence of the tesseral harmonics, quadrature formulation leads to obtain inaccurate results. The second method is the least-squares which can be considered as the best linear unbiased estimator that provides the exact results. We showed that even with a low resolution grid data it is possible to reconstruct the data and achieve an accurate result by using this method, which is extremely remarkable in three-dimensional global convection studies. However, special care has to be taken since there is some source of errors that might influence the efficiency of this method.
In general, to better understanding of the properties of the mantle, it is useful to assess observable characteristics of plumes in the mantle, including geoid, topography and heat flow anomalies. However, only few studies exist on geoid and topography for axi-symmetric convection and their models were restricted to isoviscous (or stratified) mantle and low Rayleigh numbers. We studied fully coupled depth and temperature dependent Arrhenius type of viscosity in axi-symmetric spherical shell geometry in order to investigate the shape of geoid anomalies and dynamic topography above a plume. Indeed, the topography and geoid anomalies produced from plumes are sensitive to rheology of the mantle and rheology of the plume; both have effects on shape and amplitude of the geoid anomalies. As results we are able to define different classes of plumes by their geoid signals.
Mainly depth-dependent viscosity models show a geoid with negative sign above the plume which can turn to the positive sign by decrease the viscosity contrast. This can be considered as a transition between the strongly depth dependent and the constant viscosity case. Our results basically support the idea by Morgan [1965] and McKenzie [1977]. They have shown the magnitude and even the sign of the total gravity anomaly depend on the spatial variation in effective viscosity. In addition, Hager [1984] has concluded that the total gravity field is depend on the radial distribution of effective viscosity, and a small change in viscosity contrast leads to varying sign of the response function.
In the case of temperature-dependent viscosity, the formation of an immobile lithosphere is a natural result, and the flow as well as the total geoid becomes strongly time dependent. When we increase the activation energy, all geoids associated with the first arriving plumes look like bell shaped whereas for typical plumes, after reaching a statistical steady state, bell-shaped geoids with decreasing amplitude as well as linear flank shaped geoids are observed. It is surprising that in spite of large differences in lateral and depth varying viscosities, the shapes of the geoid anomalies remained rather similar. We also identified different behaviors in the combined model with temperature-and pressure-dependent viscosity. In fact, in spite of the strongly different rheology, the geoid anomalies in all cases were surprisingly similar. Furthermore, we proposed a scaling law for the geoid which makes our results directly applicable to other planets. Moreover, we can apply the results of our calculation to find relations between different rheology and sub-lid temperature, since we know that the mantle temperature can change significantly with variation in pressure-temperature dependent viscosity. It is also possible to define a range of stagnant lid thickness related to the amplitude of the geoid which can be reasonable for study of the lid thickness in Venus or Mars.
Nevertheless, in these series of models, we simplified a number of complexities within the Earth. One of the most important of such simplification is the Boussinesq approximation. This approximation is valid if the temperature scale height (i.e. the depth over which temperature increases by a factor of “ ” due to adiabatic compression) is much greater than the convection depth. However, a temperature scale height in the Earth’s mantle is at best only slightly greater than the mantle depth. Hence, the Boussinesq approximation could mask some very important stratification and compressibility effects that influence both the spatial and temporal structure of the convection. Therefore, in more advance models we considered compressibility in our mantle convection models, assuming that density vary both radially and laterally, being determined as a function of pressure and temperature through an appropriate equation of the state. Moreover, thermodynamic properties assumed to be a function of depth.
We examined the details of the structure of the spherical axi-symmetric Anelastic Liquid Approximation model (ALA) with special attention to the Arrhenius rheology, and compare it to the cases of compressible convection without depth dependent thermodynamical properties, and to cases of the extended Boussinesq approximation. At the same time, the effects of the interaction between temperature and pressure-dependent viscosity and thermodynamic parameters in the compressible mantle convection on the geoid and topography have been studied. We showed that assuming compressible convection with depth-dependent thermodynamic properties strongly influence the geoid undulations. Using compressible convection with constant thermodynamic properties is physically inconsistent and may lead to spurious results for the geoid and convection pattern. Indeed, by a systematic study of different approaches of compressibility in the spherical shell convection for different Arrhenius viscosity laws we proved that only in the unrealistic case of zero activation energy the different compressibility modes result in comparable convection and geoid patterns. In all other rheological cases, large differences have been obtained, that stressing the important role of consistent compressible thermodynamic properties for mantle convection.
In addition, we examine the impact of compressibility as well as different rheologies on the power law relation that connects the Nusselt number to the Rayleigh number. We have discovered that the power law index of the relationship is controlled by the rheology, independent of which approximation is used. Instead, the bound of this relation is controlled by a combination of different approximation and rheology.
Next, instead of focusing on the time evolution of mantle flow, we have carried out three-dimensional spherical shell models of mantle circulation to investigate the effects of joint radial and lateral viscosity variations on the Earth’s non-hydrostatic geoid, surface and core-mantle boundary topographies. These models include realistic lateral viscosity variations (LVV) in the lithosphere, upper mantle and lower mantle in combination with different stratified viscosity structures. We have demonstrated that the contradictory results concerning the effects of LVV can be clarified by the most straight-forward problem in geoid modeling; namely, rather poorly known stratified viscosity structure. We explored three classes of dynamic geoid models due to lateral viscosity variations. In the first class, the LVV strongly improved the fit to the observed geoid. Indeed, when the viscosity contrast between lower and upper mantles is not large enough to produce a good fit to geoid the LVVs are able to perform this action by adjusting amplitudes, so that it becomes comparable with observation. In the second class, inducing the LVV moderately improved the fit. Actually, when the geoid induced by a stratified viscosity structure already has a good correlation with observation, then the LVV causes its amplitude to further improve. In the last class, if the viscosity contrast between upper and lower mantle would be high enough, inducing LVV deteriorate the fit to the observed geoid.. Indeed, depending on the stratified viscosity, inducing the LVV may take place in one of these categories.
We also quantified the effects of LVV in the mantle and lithosphere individually. We found that the presence of LVV in the mantle (upper and lower) improves the fit to the observed geoid regardless of stratified viscosity. While LVV in the lithosphere is a crucial parameter, and dependent of the stratified viscosity, may increase or decrease the geoid fit. In fact, when the lower mantle considers being viscous enough, it would support the negative buoyancy of subducting slabs. Thus, it transmits some of the stress back to the top boundary and causes a weak coupling between slab and surface. Therefore, by including the low viscous plate boundaries in this model, the slabs and overriding plates decouples and the fit to the observed geoid degrades. In contrast, when the lower mantle viscosity is not sufficiently stiff, the presence of the low viscous plate boundaries assists to weaken the strong mechanical coupling between slab and surface. Hence, a better fit achieved.
Die Seismizität des nördlichen Oberrheingrabens (ORG) ist aufgrund seines Potentials für die geothermische Nutzung und der damit möglicherweise verbundenen seismischen Risiken von allgemeinem Interesse. Detaillierte Kenntnisse der natürlichen Seismizität erlauben Rückschlüsse auf aktive Störungszonen und Spannungsverhältnisse im Untergrund. Sie liefert außerdem wichtige Hintergrundinformationen für die Abschätzung einer möglichen induzierten Seismizität. Untersuchungen zur Charakterisierung der natürlichen Seismizität, des Spannungsfeldes und der seismischen Gefährdung des nördlichen ORG sind Hauptbestandteil dieser Arbeit, die innerhalb des BMU/BMWi-Projektes SiMoN (Seismisches Monitoring im Zusammenhang mit der geothermischen Nutzung des Nördlichen Oberrheingrabens) entstanden ist. Aufzeichnungen eines Netzwerkes aus 13 seismischen Stationen dienen als Datengrundlage zur Charakterisierung der Seismizität innerhalb eines etwa 50 x 60 km2 großen Areals im dichtbesiedelten Rhein-Main Gebiet. Untersuchungen der Rauschbedingungen zur Bewertung der Eignung der Stationsorte für das Aufzeichnen der natürlichen Seismizität lieferten bei den Stationen auf felsigem Untergrund sehr gute spektrale Eigenschaften, während alle Stationen im Sediment des ORG deutlich höhere Rauschanteile aufzeigten. Anhand systematischer Messungen in flachen Bohrlöchern konnten laterale und vertikale Variationen des seismischen Rauschens beschrieben werden und dadurch eine Verbesserung der Detektionsschwelle beobachtet werden.
Es werden die Ergebnisse des seismischen Monitorings für den Zeitraum November 2010 bis Dezember 2014 dargestellt. Die Detektionsschwelle für das Netzwerk liegt bei einer Lokalmagnitude von etwa 0,5, die Vollständigkeitsmagnitude beträgt Mc = 1,2. Seit Beginn der Datenaufzeichnung konnten 243 Erdbeben im unmittelbaren Bereich des Stations-netzwerkes mit Magnituden im Bereich zwischen ML = -0,5 und ML = 4,2 lokalisiert werden. Die Epizentren liegen hauptsächlich entlang der östlichen Grabenschulter und im Graben; entlang der westlichen Grabenschulter ist die seismische Aktivität deutlich geringer. Eine weitere aktive Region konnte entlang der südlichen Ausläufer des Taunus im Nordwesten des Untersuchungsgebietes identifiziert werden. Die Seismizität erstreckt sich bis in eine Tiefe von 24 km mit einem Maximum der hypozentralen Tiefenverteilung im Bereich von 12-18 km. Im Graben ist die Seismizität dabei auf die tiefere Kruste im Bereich von 9-24 km beschränkt. Das Fehlen von seismischer Aktivität in der oberen Kruste bis ca. 9 km Tiefe im Graben könnte auf eine aseismische Deformation in diesem Tiefenbereich hindeuten. Seit Mai 2014 konnte südöstlich von Darmstadt bei der Ortschaft Ober-Ramstadt zum ersten Mal seit fast 150 Jahren eine Schwarmbebenaktivität im Bereich des nördlichen ORG registriert werden. Die Hypozentren sind in zwei Cluster unterteilt, die räumlich voneinander getrennt sind und unterschiedliche Aktivitätsraten aufweisen. Die Herdtiefen liegen im Bereich von 1-8 km.
Zusätzlich zu den Daten des SiMoN Netzwerkes wurden Aufzeichnungen der regionalen Erdbebendienste in Herdflächenanalysen für insgesamt 58 Erdbeben einbezogen. Die Herdflächenlösungen weisen überwiegend Blattverschiebungen (Strike-slip-Mechanismen) auf. Auf- und Abschiebungen spielen nur eine untergeordnete Rolle. Die berechneten Herdmechanismen bestätigen, dass sich das Spannungsfeld des nördlichen ORG transtensional verhält, im Vergleich zu früheren Studien konnte jedoch eine deutlich ausgeprägte Blattverschiebungskomponente identifiziert werden. Zur Bestimmung der Hauptspannungsachsen wurde eine Inversion der Herdflächenlösungen durchgeführt und die Richtung der maximalen horizontalen Spannung, welche hauptsächlich in N135°E orientiert ist, bestimmt.
Aufbauend auf den neu gewonnen Erkenntnissen zur natürlichen Seismizität und zum Spannungsfeld des nördlichen ORG wurde eine probabilistische seismische Gefährdungsanalyse durchgeführt. Um Unsicherheiten in den seismischen Quellregion-modellen zu berücksichtigen, wurden sechs unterschiedliche Modelle entwickelt. Für jede Quellregion wurden spezifische Parameter bestimmt. Ihre Unsicherheiten werden in einem logischen Baum behandelt. Auf der Grundlage eines neu zusammengestellten Momentmagnituden-basierten Erdbebenkatalogs wurden die Magnitudenhäufigkeits-parameter bestimmt. Unter Berücksichtigung des tektonischen Regimes in jeder Quelle wurden unterschiedliche Dämpfungsrelationen der Bodenbeschleunigung verwendet. Zur Quantifizierung der maximal zu erwartenden Magnitude in jeder Quelle wurden Wahrscheinlichkeitsdichtefunktionen berechnet. Die Resultate der Gefährdungsanalyse werden in Form von Karten der Spektralbodenbeschleunigungen und Spitzenboden-beschleunigungen für Wiederkehrperioden von 475 und 2475 Jahren und Antwortbeschleunigungsspektren dargestellt. Im Vergleich zu früheren Studien konnte eine erhöhte seismische Gefährdung für den nördlichen ORG festgestellt werden.
This study describes the Holocene sedimentary lagoonal deposition history, including event sedimentation and benthic foraminiferal analyzes, from about 10 kyrs BP until today. This is the first study describing the sedimentation of a Maldivian atoll lagoon in such detail. Thirty-nine sediment cores have been recovered from the deep Rasdhoo Atoll lagoon of the Maldives (4°N/73°W). Seventeen sediment cores were opened, described, and 296 sediment samples have been collected and analyzed. Different methods have been used to evaluate the coarse- and fine-grained carbonate components and a total of fifty-eight samples have been dated radiometrically by Beta Analytic Inc., Miami, Florida. In general, the Rasdhoo Atoll lagoon sediments can be divided into (1) a Late Pleistocene soil, (2) an early Holocene peat layer composed of mangrove deposits which mark the beginning inundation of the atoll lagoon by the rising Holocene sea-level at 10,320 ± 100 yrs BP, and (3) carbonate sediments starting to fill up the lagoon 7850 ± 140 yrs BP until today. The transition from peat to carbonate is characterized by a considerable hiatus. Six different carbonate sediment facies are classified by statistical analyses, listed in decreasing abundance:
(1) mollusk-coral-algal floatstone to rudstone (30%)
(2) mollusk-coral-red algae rudstone (23%)
(3) mollusk-coral-algal wackestone to floatstone (23%)
(4) mollusk-coral wackestone (13%)
(5) mollusk-coral mudstone to wackestone (9%)
(6) mollusk mudstone (2%)
Based on grain-sizes in combination with coral identification, the facies represent both lagoonal background sedimentation (mostly fine-grained sediments (matrix >50%)) and event sedimentation (coarse-grained sediment layers composing reefal components).
Six coarser grained layers in muddy background sediments of the Rasdhoo Atoll lagoon were interpreted as Holocene tsunami events, based on the increase of allochthonous skeletal material with shallow-water reef affinity such as fragments of shallow-water coral species, coralline red algae, and reef-dwelling foraminifera in these layers, as well as AMS dating:
• Event 1: 420 - 890 yrs BP (655 yrs BP)
• Event 2: 890 - 1560 yrs BP (1225 yrs BP)
• Event 3: 2040 - 2340 yrs BP (2190 yrs BP)
• Event 4: 2420 - 3380 yrs BP (2900 yrs BP)
• Event 5: 3890 - 4330 yrs BP (4110 yrs BP)
• Event 6: 5480 - 5760 yrs BP (5620 yrs BP)
Five of the six layers may be correlated to previously published tsunami events at adjacent coastal research sites. The mid-late Holocene atoll lagoon archive is incomplete though based on the assumption that major earthquakes at the Indonesian subduction zone generated more than six major tsunamis during the past 6.5 kyrs.
According to Gischler (2006), the sediments of the Rasdhoo Atoll lagoon can be divided into two areas: (1) a central to marginal deep lagoon with a lateral west-to-east gradient of sediment facies distribution, visible in sections <4 kyrs BP with sedimentary facies of mudstone to wackestone in the western part (e.g., cores 16, 18, and 34) and coarse-grained coral and algal-rich sediments in the eastern part of the lagoon (e.g., cores 30 and 31). (2) A northern enclosed and shallow area between the sand apron and the sand spit accumulating “sandy” sediments of wackestone facies (cores 2, 19, 25, and 26).
Comparing the sediment accumulation data of the lagoon with two reconstructed local sea-level curves, three different sequence-stratigraphical systems tracts are visible: (1) a lowstand systems tract (LST) >10 kyrs BP. Pleistocene brownish soil superposing subaerially exposed Pleistocene reef limestone. (2) A transgressive systems tract (TST) 10-6.5 kyrs BP. A peat layer marks the beginning of the inundation, and the carbonate sedimentation starts with very low sedimentation rates of 0.02 m/kyr. (3) A highstand systems tract (HST) 6.5-0 kyrs BP, further divided into three stages (6.5-3, 3-1, 1-0 kyrs BP). The sea-level rise slowed down, sedimentation rates are increasing continuously up to a maximum of 1.4 m/kyr, the sand spit developed some 4 kyrs BP, the lagoonal circulation got restricted, and the lateral west-to-east gradient of grain-size accumulation started. From 1-0 kyrs BP the sedimentation rates slowed down to modern mean sedimentation rates of 0.6 m/kyr.
Two cores, one core from the center of the lagoon (core 16) and one core from the northern margin of the lagoon (core 19), have been analyzed on diversity and assemblages of benthic foraminifera in high-resolution. The transitions of Ammonia spp. to a more even and diverse fauna marks a significant environmental change at 7.0 kyrs BP in core 16 (onset of a stable environment in the deep lagoon after the sea-level rise slowed down at HST stage 1) and at 4.0 kyrs BP in core 19. A continuing environmental change after 1.4 kyrs BP in core 16 caused the fauna to become more even, a recovery of diversity and a permanent decline of foraminiferal accumulation rate. The changes in the faunas at 4.0 kyrs BP and at 1.4 kyrs BP could be explained with the sand spit formation in the northwestern and western lagoon. The sand spit has apparently acted as an obstacle in lagoonal circulation and might have caused unstable environmental conditions due to a more rapid circulation at the shallow marine site of core 19 and a slowdown of bottom water circulation in the main lagoon (core 16) leading to higher residence times and to lower oxygen and higher nutrient concentrations.
Derivation and characterization of a new filter for nonlinear high-dimensional data assimilation
(2015)
Data assimilation (DA) combines model forecasts with real-world observations to achieve an optimal estimate of the state of a dynamical system. The quality of predictions in nonlinear and chaotic systems such as atmospheric or oceanic circulation is strongly sensitive to the initial conditions. Therefore, beyond the consistent reconstruction of past states, a primary relevance of advanced DA methods concerns the proper model initialization. The ensemble Kalman filter (EnKF) and its deterministic variants, mostly square root filters such as the ensemble transform Kalman filter (ETKF), represent a popular alternative to variational DA schemes. They are applied in a wide range of research and operations. Their forecast step employs an ensemble integration that fully respects the nonlinear nature of the analyzed system. In the analysis step, they implicitly assume the prior state and observation errors to be Gaussian. Consequently, in nonlinear systems, the mean and covariance of the analysis ensemble are biased and these filters remain suboptimal. In contrast, the fully nonlinear, non-Gaussian particle filter (PF) relies on Bayes' theorem without further assumptions, which guarantees an exact asymptotic behavior. However, it is exposed to weight collapse, particularly in higher-dimensional settings, known as the curse of dimensionality.
This work presents a new method to obtain an analysis ensemble with mean and covariance that exactly match the corresponding Bayesian estimates. This is achieved by a deterministic matrix square root transformation of the forecast ensemble, and subsequently a suitable random rotation that significantly contributes to filter stability while preserving the required second-order statistics. The forecast step remains as in the ETKF. The algorithm, which is fairly easy to implement and computationally efficient, is referred to as the nonlinear ensemble transform filter (NETF). The limitation with respect to fully-nonlinear filtering is that the NETF only considers the mean and covariance of the Bayesian analysis density, neglecting higher-order moments.
The properties and performance of the proposed algorithm are investigated via a set of experiments. The results indicate that such a filter formulation can increase the analysis quality, even for relatively small ensemble sizes, compared to other ensemble filters in nonlinear, non-Gaussian scenarios. They also confirm that localization enhances the applicability of this PF-inspired scheme in larger-dimensional systems. Finally, the novel filter is coupled to a large-scale ocean general circulation model with a realistic observation scenario. The NETF remains stable with a small ensemble size and shows a consistent behavior. Additionally, its analyses exhibit low estimation errors, as revealed by a comparison with a free ensemble integration and the ETKF. The results confirm that, in principle, the filter can be applied successfully and as simple as the ETKF in high-dimensional problems. No further modifications are needed, even though the algorithm is only based on the particle weights. Thus, it is able to overcome the curse of dimensionality, even in deterministic systems. This proves that the NETF constitutes a promising and user-friendly method for nonlinear high-dimensional DA.
In the past sixty years, excessive water consumption and dam construction have significantly influenced natural flow regimes and surface freshwater ecosystems throughout China, and thus resulted in serious environmental problems. In order to balance the competing water demands between human and environment and provide knowledge on sustainable water management, assessments on anthropogenic flow alterations and their impacts on aquatic and riparian ecosystems in China are needed.
In this study, the first evaluation on quantitative relationships between anthropogenic flow alterations and ecological responses in eleven river basins and watersheds in China was performed based on the data that could be obtained from published case studies. Quantitative relationships between changes in average annual discharge, seasonal low flow and seasonal high flow and changes in ecological indicators (fish diversity, fish catch and vegetation cover, etc.) were analyzed. The results showed that changes in riparian vegetation cover as well as changes in fish diversity and fish catch were strongly correlated with the changes in flow magnitude (r = 0.77, 0.66), especially with changes in average annual river discharge. In addition, more than half of the variations in vegetation cover could be explained by changes in average annual river discharge (r² = 0.63) and roughly 50 % changes in fish catch in arid and semi-arid region and 60% changes of fish catch in humid region could be related to alterations in average annual river discharge (r² = 0.53, 0.58).
In a supplementary analysis of this study, the first estimation on quantitative relationships between decreases in native fish species richness and anthropogenic flow alterations in 34 river basins and sub-basins in China was conducted. Linear relationships between losses of native fish species and five ecologically relevant flow indicators were analyzed by single and multiple regression models. For the single regression analysis, significant linear relationships were detected for the indicators of long-term average annual discharge (ILTA) and statistical low flow Q90 (IQ90). For the multiple regressions, no indicator other than ILTA has significant relationships with changes in number of fish species mainly due to collinearity. Two conclusions emerged from the analysis: 1) losses of fish species were positively correlated with changes in ILTA in China and 2) indicator of ILTA was dominant over other flow indicators included in this research for the given dataset. These results provide a guideline for the sustainable water resources management in rivers with high risk of fish extinction in China.
Bayesian Networks are computer-based environmental models that are frequently used to support decision-making under uncertainty. Under data scarce conditions, Bayesian Networks can be developed, parameterized, and run based on expert knowledge only. However, the efficiency of expert-based Bayesian Network modeling is limited by the difficulty in deriving model inputs in the time available during expert workshops. This thesis therefore aimed at developing a simple and robust method for deriving conditional probability tables from expert estimates in a time-efficient way. The design and application of this new elicitation and conversion method is demonstrated using a case study in Xinjiang, Northwest China. The key characteristics of this method are its time-efficiency and the approach to use different conversion tables based on varying levels of confidence. Although the method has its limitations, e.g. it can only be applied for variables with one conditioning variable; it provides the opportunity to support the parameterization of Bayesian Networks which would otherwise remain half-finished due to time constraints. In addition, a case study in the Murray-Darling Basin, Australia, is used to compare Bayesian Network types and software to improve the presentation clarity of large Bayesian Networks. Both case studies aimed at gaining insights on how to improve the applicability of Bayesian Networks to support environmental management.
The Late Cretaceous is known to be mostly affected by warm periods interrupted temporarily by a number of cooling events. The reconstruction of the paleoclimatic conditions during a period of high concentration of CO2 in the atmosphere is of great importance for the creation of future climate models. We applied the recently developed method reconstructing the SST from the TEX86 (TetraEther indeX of tetraethers consisting of 86 carbon atoms).
The sample material used for the present study was obtained from the tropical Late Cretaceous southern Tethys upwelling system (Negev/Israel), lasting from the Late Santonian to the Early Maastrichtian (~ 85 to 68 Ma). On the core samples from the Shefela basin, representing the outer belt of the upwelling system and the outcrop profile from the open mine Mishor Rotem (Efe Syncline), representing the inner belt, various bulk geochemical and biomarker studies were performed in this thesis.
Derived from TEX86 data, a significant long-term SST cooling trend from 36.0 to 29.3 °C is recognized during the Late Santonian and the Early Campanian in the southern Tethys margin. This is consistent with the opening and deepening of the Equatorial Atlantic Gateway (EAG) and the intrusion of cooler deep water from the southern Atlantic Ocean influencing the global SSTs and also the Tethys Ocean. Furthermore, the cooler near shore SST usually found in modern upwelling systems could be verified in case of the ancient upwelling system investigated in the present study. The calculated mean SST in the inner belt (27.7 °C) represented in the Efe Syncline was 1.5 °C cooler in comparison to the more seaward located outer belt (Shefela basin).
Moreover, geochemical and biomarker analyses were used to identify both the accumulation of high amounts of phosphate in the PM and good preservation of organic matter (OM) in the lower part of the OSM section. Total organic carbon (TOC) contents are highly variable over the whole profile reaching from 0.6 % in the MM, to 24.5 % in the OSM. Total iron (TFe) varies from 0.1 % in the PM to 3.3 % in the OSM and total sulfur (TS) varies between 0.1 % in the MM and 3.4 % in the OSM. Different correlations of TS, TOC and TFe were used to identify the conditions during the deposition of the different facies types. Natural sulfurization was found to play a key role in the preservation of the OM particularly in the lower part of the OSM. Samples from the OSM and the PM were deposited under dysoxic to anoxic conditions and iron limitation lasted during the deposition of the OSM and the PM, which effected the incorporation of sulfur into OM.
Phosphorus is highly accumulated in the sediments of the PM with a mean proportion of 11.5 % total phosphorus (TP), which is drastically reduced to a mean value of 0.9 % in the OSM and the MM. From the correlation of the bulk geochemical parameters TOC/TOCOR ratio and TP a major contribution of sulfate reducing bacteria to the phosphate deposition is concluded. This interrelation has previously been investigated in recent coastal upwelling systems off Peru, Chile, California and Namibia. This was further supported by the analysis of branched and monounsaturated fatty acids indicating the occurrence of sulfate reducing and sulfide oxidizing bacteria during the deposition.
According to the results from the analysis of n-alkanes and C27- to C29-steranes up to 95 % of the OM was of marine origin.
Organic sulfur compounds (OSC) were a major compound class in the aromatic hydrocarbon fraction and n-Alkyl and isoprenoid thiophenes were the most abundant, with highest amounts found for 2-methyl-5-tridecyl-thiophene (28 µg/g TOC). The relatively high abundance of ββ-C35 hopanoid thiophenes and epithiosteranes is equivalent to an incorporation of sulfur during the early stages of diagenesis.
Moreover, the geochemical parameters δ13Corg, δ15Norg, C/N and the pristane/phytane (Pr/Ph) ratio, were studied for reconstruction of seafloor and water column depositional environments. The high C/N ratio along with relatively low values of δ15Norg (4 ‰ to 6 ‰) and δ13Corg (-29 ‰ to -28 ‰) are consistent with a significant preferential loss of nitrogen-rich organic compounds during diagenesis. Oxygen-depleted conditions lasted during the deposition of the PM and the bottom of the OSM, reflected by the low Pr/Ph ratio of 0.11–0.7. In the upper part of the OSM and the MM the conditions changed from anoxic to dysoxic or oxic conditions. This environmental trend is consistent with co-occurring foraminiferal assemblages in the studied succession and implies that the benthic species in the Negev sequence were adapted to persistent minimum oxygen conditions by performing complete denitrification as recently found in many modern benthic foraminifera.
Furthermore, the anammox process could have influenced the nitrogen composition of the sediments. In this anaerobically process nitrite and ammonia are converted to molecular nitrogen.
Das Thema dieser Arbeit war die Untersuchung der natürlichen Variationen von den zwei primordialen Uranisotopen (238U und 235U) mit einem Schwerpunkt auf Proben, die (1) die kontinentale Kruste und ihre Verwitterungsprodukte (d.h. Granite, Shales und Flusswasser) repräsentieren, (2) Produkte der hydrothermalen Alteration vom mittelozeanischen Rücken widerspiegeln (d.h. alterierte Basalte, Karbonatgänge und hydrothermales Wasser) und (3) aus abgegrenzten euxinischen Becken (d.h. Proben aus der Wassersäule und den dazugehörigen Sedimenten) stammen. Das allgemeine Ziel war das Verständnis, unter welchen Bedingungen und Mechanismen eine Fraktionierung der zwei häufigsten Uranisotope (238U und 235U) in der Natur erfolgt, zu verbessern.
Die untersuchten Haupt- und Nebenflüsse unterscheiden sich sowohl in Ihrer Urankonzentration (c(U)) als auch in Ihrer Uranisotopenzusammensetzung (δ238U), wobei die Nebenflüsse eine geringere Urankonzentration (0.87 nmol/kg bis 3.08 nmol/kg) und eine schwerere Uranisotopenzusammensetzung aufweisen (-0.29 ‰ bis +0.01 ‰ im δ238U) im Vergleich zu den Hauptflüssen (c(U) = 5.19 nmol/kg bis 11.69 nmol/kg und d238U = -0.31 ‰ bis +0.13 ‰) aufweisen. Die untersuchten Gesteinsproben fallen alle in einen recht schmalen Bereich von δ238U, zwischen -0.45 ‰ und -0.21 ‰, mit einem Durchschnittswert von -0.30 ‰ ± 0.04 ‰ (doppelte Standardabweichung). Deren Uranisotopenvariationen sind unabhängig von der Urankonzentration (11.8 µg/g bis 1.3 µg/g), dem Alter (3.80 Ga bis 328 Ma), der Probenlokalität und Grad der Differenzierung. Basierend auf den Ergebnissen der Hauptflüsse, die die Uranhauptquelle für den Ozean darstellen, schlagen wir für zukünftige Berechnungen in der Massenbilanz des Urans einen neuen Wert als beste Abschätzung für die Quelle des Urans im Ozean vor, δ238U = -0.23 ‰.
Die Produkte der hydrothermalen Alteration, alterierte Basalte und Kalziumkarbonatgänge, zeigten etwas stärkere Isotopenvariationen (δ238U zwischen -0.63 ‰ und +0.27 ‰) als erwartet und die hydrothermalen Fluide wiesen eine etwas leichtere Uranisotopenzusammensetzung als Meerwasser ((-0.43 ± 0.25) ‰ vs. (-0.37 ± 0.03) ‰) auf. Diese Ergebnisse sind in Übereinstimmung mit einem Modell, dass annimmt, dass die beobachtete Isotopenfraktionierung hauptsächlich ein Ergebnis von Redoxprozessen ist, z.B. die partielle Reduktion von löslichem UVI aus dem Meerwasser während der hydrothermalen Alteration, was zu einer Anreicherung der schweren Uranisotope in der reduzierten Uranspezies (UIV) führt und 2) das bevorzugte Entfernen von UIV aus den hydrothermalen Fluid und der Einbau in die alterierte ozeanische Kruste. Durch diesen Prozess wird das hydrothermale Fluid an schweren Uranisotopen verarmt und somit würden auch die alterierten Basalte und Karbonate ein niedriges δ238U aufweisen, wenn sie mit dem isotopisch leichten hydrothermalen Fluid in Kontakt gekommen sind.
Die Untersuchung von Wasser- und Sedimentproben aus der Ostsee und dem anoxischen Kyllaren Fjord (Norwegen) auf deren Uran- und Mo-Isotopenzusammensetzung zeigte, dass die Uranisotopenzusammensetzung der Sedimente abhängt von (1) dem Ausmaß des Uranaustrags aus der Wassersäule (in einer ähnlichen Art und Weise wie bei den Molybdänisotopen) und (2) der Sedimentationsrate, d.h. der Fraktion von authigenem- relativ zum dedritischen Uran in den Sedimenten. Aufgrund der hohen Sedimentationsrate zeigen die Sedimente aus dem Kyllaren Fjord nur eine moderate authigene Urananreicherung und eine leichtere Uranisotopenzusammensetzung als Sedimente aus dem Schwarzen Meer. In den anoxischen Becken der Ostsee erfolgt dagegen eine starke Mo- und schwache U-Isotopenfraktionierung zwischen Wasser und Sediment. Durch die regelmäßigen auftretenden Spülereignisse mit sauerstoffreichem Wasser wurden vermutlich die ursprünglichen anoxischen Mo- und U-Isotopensignaturen der Sedimente verändert. Demzufolge müssen die Sedimente durchgehend anoxischen Bedingungen ausgesetzt sein, um eine Mo- und U-Isotopensignatur von den Redoxbedingungen während der Ablagerungen zu speichern.
Der Vergleich zwischen Molybdän- und Uranisotopen in der Ostsee und dem anoxischen Kyllaren Fjord zeigte, dass sich Uran- und Molybdänisotope in stark euxinischen Wassersäulen (c(H2S) > 11 µmol/L) entgegengesetzt verhalten. Dementsprechend ergänzen sich die beiden Isotopensysteme und können genutzt werden, um die Ablagerungsbedingungen in abgeschlossenen Becken und die Redoxentwicklung des Paläoozeans zu untersuchen.
Die Anwendung der WKB-Theorie zur Simulation der schwach nichtlinearen Dynamik von Schwerewellen
(2014)
Es ist schon seit Längerem bekannt, dass Schwerewellen die Zirkulation der mittleren Atmosphäre beeinflussen. Sie werden fast ausschließlich in der Troposphäre durch Prozesse wie Gebirgsüberströmung, Konvektionen, Frontogenese etc. erzeugt. Sie propagieren von ihrem Entstehungsort in der Troposphäre in die höheren Schichten der Atmosphäre und transportieren dabei ihre Energie und ihren Impuls. Unter der Voraussetzung, dass die Energie von Schwerewellen erhalten bleibt und die Dichte der Atmosphäre mit der Höhe exponentiell abnimmt, wächst die Amplitude der Schwerewellen so stark an, dass sie brechen und ihren Impuls in Stratosphäre und Mesosphäre deponieren. Als Folge davon beeinflussen Schwerewellen die großräumige Zirkulation der Atmosphäre und sind damit ein wichtiges Bindeglied, welches die Troposphäre mit anderen Atmosphärenbereichen verbindet. Folglich ist es wichtig, dass die Klima- und Wettermodelle in der Lage sind, die Schwerewellendynamik zu beschreiben. Bedauerlicherweise können diese Modelle nicht das komplette Schwerewellenspektrum auflösen. Somit müssen Schwerewellen in den Modellen parametrisiert werden. Viele Parametrisierungsschemen basieren auf Wentzel-Kramer-Brillouin(WKB)-Theorie. Die WKB-Gleichungen, die sogenannten Strahlengleichungen, beschreiben die räumliche und zeitliche Variation der Welleneigenschaften wie Wellenzahl, Wellenamplitude und Wellenfrequenz entlang der Charakteristiken, welche durch die lokale Gruppengeschwindigkeit vorgegeben sind. Die numerische Modelle, die auf den Strahlengleichungen basieren, werden als Strahlenmodelle bezeichnet. In Strahlenmodellen werden Schwerewellen durch Wellenteilchen dargestellt. Zur Zeit verwenden die Strahlenmodelle stationäre Strahlengleichungen, da die Wechselwirkung eines zeitabhängigen Schwerewellenfeldes mit einem zeit- und ortsabhängigen Hintergrund zu Problemen in Strahlenmodellen führen kann. Die Strahlengleichungen basieren auf der Annahme, dass sich nie zwei Wellenteilchen mit den unterschiedlichen Welleneigenschaften an einer Position befinden können. Wenn an einer Position zwei Wellenteilchen mit den unterschiedlichen Wellenzahlen befinden, entsteht sogenannte Kaustik: ein Punkt im Raum, an dem sich mehrere Charakteristiken kreuzen. Wenn eine Kaustik entsteht, kann die Wellenamplitude nicht mehr bestimmt werden. Ziel der vorliegenden Arbeit ist es mithilfe der WKB-Theorie die Ausbreitung von Schwerewellenpaketen in einer raum- und zeitabhängigen Hintergrundströmung zu beschreiben und ein numerisches Modell zu entwickeln, welches die Schwerewellen parametrisieren und ihre Wechselwirkung mit der raum- und zeitabhängigen Hintergrundströmung beschreiben kann.
Einfachheitshalber wird in dieser Arbeit nur die Wechselwirkung zwischen horizontal periodischen, vertikal lokalisierten Schwerewellenpaketen und der raum- und zeitabhängigen Hintergrundströmung betrachtet.
Interpretation magnetotellurischer Messungen auf Island und 3D-Modellierungen des Island-Plumes
(2014)
Die Lage und der geologische Aufbau Islands sind eine einmalige geologische und geophysikalische Besonderheit - nur hier liegt der Mittelatlantische Rücken deutlich oberhalb des Meeresspiegels. Eine Theorie ist, dass unter Island ein sogenannter Hotspot existiert - ein aufsteigender Mantelplume (oder eine andere Temperatur- und Schmelzanomalie). Das bedeutet, dass die Tektonik, die Petrologie und die (geo)physikalischen Parameter von der Wechselwirkung der Meeresbodenspreizung mit dem aufsteigenden Mantelplume bestimmt werden. Die magnetotellurischen Untersuchungen auf Island und die magnetotellurischen Modelle der vorliegenden Arbeit lassen sich nach Zieltiefen unterteilen. Im ersten Teil steht vor allem die Untersuchung der Leitfähigkeitsstruktur des oberen Erdmantels im Vordergrund, wobei der Schwerpunkt auf Modellstudien liegt. Hier wird die Theorie des aufsteigenden Mantelplumes aufgegriffen und hinsichtlich der Möglichkeiten der Magnetotellurik (MT) diesen zu detektieren, untersucht. In dieser Arbeit werden deshalb verschiedene synthetische 3D-Modelle untersucht. Diese sollen klären, unter welchen Bedingungen, d.h. bei welcher Tiefenlage, Ausdehnung und Leitfähigkeit, ein Mantelplume in der Magnetotellurik messbare Signale liefert. Da Temperatur und Schmelzanteil hierbei eine entscheidende Rolle spielen, werden auch Ergebnisse von geodynamischen Modellierungen verwendet. Die verschiedenen Modellierungen machen deutlich, dass der Plume in Modellen mit maximal 1% Schmelzanteil nur sehr schlecht mit der MT aufgelöst werden kann. Ein weiteres Problem ist die relativ geringe laterale Ausdehnung des Bereichs hoher Leitfähigkeit. Insbesondere bei Berücksichtigung des Krustenleiters liegen die Effekte des Plumes im Bereich der Messfehler bei realen Daten. Erst bei 3% Schmelzanteil im Plume ergeben sich Charakteristiken in den Sondierungskurven, die eindeutig dem Plume zugeordnet werden können. Im zweiten Teil liegt das Augenmerk auf der Leitfähigkeitsstruktur der isländischen Kruste, für deren Untersuchung ca. 200 Datensätze aus zahlreichen deutsch-isländischen Messkampagnen zur Verfügung stehen. In dieser Arbeit werden sie ganzheitlich ausgewertet und interpretiert. Hier steht im Speziellen der in verschiedenen früheren Untersuchungen gefundene gute Leiter in ca. 10 km Tiefe im Vordergrund. Seine Ausdehnung, Tiefenlage und Leitfähigkeit sowie laterale Änderungen werden genauer untersucht. Dazu werden aus den gemessenen Daten und den daraus ermittelten magnetotellurischen Impedanztensoren nicht nur die Sondierungskurven, sondern weitere Parameter wie Phasentensoren und Rotationsinvarianten abgeleitet und diskutiert. Um einen Überblick über die räumliche Verteilung der Untergrundstrukturen zu erhalten, werden die einzelnen Messpunkte charakterisiert und Stationen mit ähnlichem Verhalten in Gruppen zusammengefasst. 1D- und 2D- Inversionsmodelle liefern einen direkten Hinweis auf die Leitfähigkeitsverteilung. Diese zeigt ausgeprägte laterale Änderungen. Aus den 2D-Modellen ergeben sich Hinweise, die darauf schließen lassen, dass diese Zone niedrigen Widerstands nicht durchgängig oder geschlossen sein muss, um die gemessenen Daten zu erklären. Der gute Leiter scheint weniger mit der Aufwölbung durch den vermuteten Mantelplume oder eine andere tiefer liegende Schmelzanomalie korreliert zu sein. Die lateralen und vertikalen Variationen lassen auf einen Zusammenhang mit den Vulkansystemen auf Island schließen. Darauf deuten auch die Induktionsvektoren hin, die lateral betrachtet stark variieren. Ein weiteres Ergebnis ist das Fehlen dieses Krustenleiters in einem mindestens 20km breiten Streifen entlang der Südküste.
Gridded maps of meteorological variables are needed for the evaluation of weather and climate models and for climate change monitoring. In order to produce them, values at locations where no observing stations are available need to be estimated from point-wise observations. For the interpolation of meteorological observations deterministic and stochastic methods are often combined. Deterministic methods can account for ancillary information such as elevation, continentality or satellite observations. Stochastic methods such as kriging reproduce observed values at the station locations and also account for spatial variability. In the first two studies of this thesis, a flexible interpolation method for the gridding of locally observed daily extreme temperatures is developed that also provides an optimal estimate of the interpolation ncertainty. In the third study, an observational dataset is created using this interpolation method and then applied to evaluate a climate simulation for Africa.
In the first study, the Regression-Kriging-Kriging (RKK) method is tested for the interpolation of daily minimum and maximum temperatures (Tmin and Tmax) in different regions in Europe. RKK accounts for elevation, continentality index and zonal mean temperature and is applicable in regions of differing station density and climate. The accuracy of RKK is compared to Inverse Distance Weighting, a common deterministic interpolation method, and to Ordinary Kriging, a common stochastic interpolation method. The first step in RKK is to use regression kriging, in which multiple linear regression accounts for topographical effects on the temperature field and kriging minimizes the regression error, to interpolate climatological means. In the second step daily deviations from the monthly climatology are interpolated using simple kriging. Owing to the large climatological differences across the investigation area the interpolation is performed in homogeneous subregions defined according to the Köppen-Geiger climate classification. Cross validation demonstrates the superiority of RKK over the simpler algorithms in terms of accuracy and preservation of spatial variability. The interpolation performance however strongly varies across Europe, being considerably higher over Central Europe (highest station density) than over Greenland (few stations along the coast line). This illustrates the strong impact of the station density on the accuracy of the interpolation result. Satellites provide comprehensive observations of climate variables such as land surface temperature (LST) and cloud cover (CC). However, LST is associated with high uncertainty (standard error ~ 1-2°C), preventing its direct application in meteorology and climatology. The second study investigates the usefulness of LST and CC as predictors for the gridding of daily Tmin and Tmax. The RKK algorithm is compared with similar interpolation methods that apply LST and CC in addition to the predictors used with the RKK algorithm. The investigation is conducted in two regions, Central Europe and the Iberian Peninsula, which differ strongly in average cloud cover (Central Europe is approximately 30% cloud free and the Iberian Peninsula approximately 60 % cloud free). RKKLST (in which monthly mean LST is used as an additional predictor) yields for Central Europe no clear improvement over RKK, yet it reduces the interpolation error over the Iberian Peninsula. This finding can be explained by the higher percentage of cloud free pixels over that region in summer which enables a more robust determination of monthly mean LST. Adding a regression step for daily anomalies (using the predictor CC) yields the RKRK method and improves the preservation of spatial variability over the Iberian Peninsula. Moreover, a successive reduction of the station number (from 140 to 10 stations) reveals an increasing superiority of RKKLST and RKRK over RKK in both regions.
The application of a gridded observational dataset for climate monitoring or climate model validation requires knowledge of the uncertainties associated with the dataset. The estimation of the interpolation uncertainty, here the inter quartile range is the used uncertainty measure, is therefore an important issue within the frame of this thesis. By means of cross validation it is shown that the largest uncertainties occur in regions of low station density (e.g. Greenland), in mountainous regions and along coastlines (in these regions model evaluation results should be interpreted carefully). The magnitude of the interpolation error mainly depends on the station density, while the complexity of terrain has substantially less influence. On average over all regions and investigation days the target precision of the uncertainty estimate is reached. However, on local scales and for single days it can be clearly over- or underestimated. The application of satellite-derived predictors (LST and CC) yields no noteworthy improvement of the uncertainty estimate.
In the last study two regional climate simulations for Africa using the ERA-Interim driven COSMO-CLM (CCLM) model at two different horizontal resolutions (0.22° and 0.44°) are validated. It is assessed whether observed patterns and statistical properties of daily Tmin and Tmax are correctly represented in the model. The ERA-Interim reanalysis and a specially created observational dataset are used as reference. The observational dataset is generated by applying the RKRK algorithm (developed within the second study). The investigations show an occasionally large bias in Tmin and Tmax. The hemispheric summers are generally too warm and the temporal variability in temperature is too high, particularly over extra tropical Africa. The diurnal temperature range is overestimated by about 2°C in the northern subtropics but underestimated by about 2°C over large parts of the African tropics. CCLM reproduces the observed frequency distribution of daily Tmin and Tmax in all African climate regions, and the extreme values in the lower percentiles (5, 10, 20%) for Tmin are well simulated. The higher percentiles (80, 90, 95%) for Tmax are however overestimated by 2-5°C. For both Tmin and Tmax the 0.22° simulation is on average 0.5°C warmer than the 0.44° simulation. Additionally, the higher percentiles are about 1°C warmer for both Tmin and Tmax in the higher resolution run, while the lower percentiles in both runs match very well. Although the temperature pattern is represented in more detail along the coastlines and in topographically complex regions, the higher resolution simulation yields no qualitative improvement.
To summarize, the choice of the appropriate algorithm mainly depends on the interpolation conditions. In cases where the station density is high across the target region and the predictor space is adequately covered by observing stations, the computationally less demanding RK algorithm should be preferred. In regions where the station density is low the more robust RKRK algorithm should be the first choice. Due to the strong physical relation of both CC and LST to Tmin and Tmax the missing information is at least partially compensated for. The estimation of the interpolation uncertainty could be improved by applying a normal score transformation to the data prior to a kriging step. This is because the kriging assumption that the increments of the variable of interest are second order stationary can be approximately met by a normal score transformation.
The objective of the present doctoral thesis was to investigate the occurrence, distribution, and behaviour of six hydrophilic ethers: ethyl tert-butyl ether (ETBE), 1,4-dioxane, ethylene glycol dimethyl ether (monoglyme), diethylene glycol dimethyl ether (diglyme), triethylene glycol dimethyl ether (triglyme), and tetraethylene glycol dimethyl ether (tetraglyme) in surface-, waste-, ground- and drinking water samples. Solid phase extraction and gas chromatography/mass spectrometry were used to analyze the six hydrophilic ethers. Altogether more than 150 surface water samples, almost 100 of each groundwater and wastewater samples, and 10 raw and drinking water samples were analyzed during the research project.
Initially, the method was validated in order to simultaneously determine the analytes of interest in various aquatic environments. A solid phase extraction method that uses coconut charcoal (Resprep® activated coconut charcoal, Restek) or carbon molecular sieve material (SupelcleanTM Envi-CarbTM Plus, Supelco) for analyte absorption were found suitable for determination of ETBE, 1,4-dioxane, and glymes in surface-, drinking-, ground- and wastewater samples. Precision and accuracy of both methods was demonstrated for all analytes of interest. The recovery of target compounds from the ultrapure water spiked at 1.0 µg L−1 was between 86.8 % and 98.2 %, with relative standard deviation below 6 %. The samples spiked at 10.0 µg L−1 gave slightly higher recovery of 90.6 % to 112.2 % with a relative standard deviation below 3.4 % for each analyte. Detection and quantification limits in ultrapure water and surface waters were furthermore established. The limit of quantitation (LOQ) in ultrapure water ranged between 0.024 µg L−1 to 0.057 µg L−1 using Restek cartridges, and 0.030 µg L−1 to 0.069 µg L−1 using Supelco cartridges. In the surface water samples the calculated LOQ was 0.032 µg L−1 to 0.067µg L−1 using coconut charcoal material and 0.032 µg L−1 to 0.052 µg L−1 using the carbon molecular sieve material. Moreover, stability of the unpreserved and preserved water samples as well as the extracts was determined. Preservation of samples with sodium bisulfate (at 1 gram per Liter) resulted in much better stability of the ethers in water samples. Subsequently, 27 samples obtained from seven surface water bodies in Germany (Rivers Rhine, Lippe, Main, Oder, Rur, Schwarzbach and Wesel-Datteln Canal) were analyzed for the six hydrophilic ethers. ETBE was present in only two surface waters (Rhine River and Wesel-Datteln Canal) with concentrations close to the LOQ (up to 0.065 µg L−1). 1,4-Dioxane was detected in all of the water samples at concentrations reaching 1.93 µg L–1. Monoglyme was identified only in the Main and Rhine Rivers at the maximum concentration of 0.114 µg L–1 and 0.427 µg L–1, respectively. Very high concentrations (up to 1.73 µg L−1) of diglyme, triglyme, and tetraglyme were detected in the samples from the Oder River. These glymes were also detected in the Rhine River; however the concentrations did not exceed 0.200 µg L–1. Furthermore, tetraglyme was detected in the Main River at an average concentration of 0.409 µg L–1 (n = 6) and in one sample from the Rur River at 0.192 µg L–1.
Four sampling campaigns were conducted at the Oderbruch polder between October 2009 and May 2012, in order to study the behavior of the hydrophilic ethers and organophosphates during riverbank filtration and in the anoxic aquifer. Moreover the suitability of these target compounds was assessed for their use as groundwater organic tracers. At the time of each sampling campaign, concentrations of triglyme and tetraglyme in the Oder River were between 20–185 ng L–1 (n = 4) and 273¬–1576 ng L–1 (n = 4). Monoglyme, diglyme, and 1,4-dioxane were analyzed only during the two last sampling campaigns. At that time, the concentration of diglyme in Oder River was 65¬–94 ng L-1 (n = 2) and 1,4-dioxane 1610¬–3290 ng L–1 (n = 2). In the drainage ditch, following bank filtration, concentrations of ethers ranged between 1090 ng L–1 and 1467 ng L–1 for 1,4-dioxane, 23¬ng L–1 and 41 ng L–1 for diglyme, 37 ng L–1 and 149 ng L–1 for triglyme, and 496 ng L–1 and 1403 ng L–1 for tetraglyme. In the anoxic aquifer, 1,4-dioxane showed the greatest persistence during the groundwater passage. At the distance of 1150 m from the river and an estimated groundwater age of 41.9 years, a concentration above 200 ng L−1 was detected. A positive correlation was found for the inorganic tracer chloride (Cl−) with 1,4-dioxane and tetraglyme. Similarities in the behavior of Cl− and the organic compound suggested that 1,4-dioxane and tetraglyme are controlled by the same hydraulic process and therefore can be used as additional tracers to study the dynamics of the groundwater system. These results show that high concentrations of ethers are present in the surface water and are not removed during bank filtration processes. Moreover, the hydrophilic ethers persist in the anoxic aquifer and little or no degradation is expected, supporting, their possible application as organic tracers.
A separate sampling project was conducted for 1,4-dioxane that focused primarily on its fate in the aquatic environment. This study provided missing information on the extent of water pollution with 1,4-dioxane is Germany. Numerous waste-, surface-, ground- and drinking water samples were collected in order to determine the persistence of 1,4-dioxane in the aquatic environment. The occurrence of 1,4-dioxane was determined in wastewater samples from four municipal sewage treatment plants (STP). The influent and effluent samples were collected during weekly campaigns. The average influent concentrations in all four plants ranged from 262 ± 32 ng L−1 to 834 ± 480 ng L−1, whereas the average effluents concentrations were between 267 ± 35 ng L−1 and 62,260 ± 36,000 ng L−1. The source of increased 1,4-dioxane concentrations in one of the effluents was identified to originate from impurities in the methanol used in the postanoxic denitrification process. Spatial and temporal distribution of 1,4-dioxane in the river Main, Rhine, and Oder was also examined. Concentrations reaching 2,200 ng L−1 in the Oder River, and 860 ng L−1 in both Main and Rhine River were detected. The average load during the sampling was estimated to be 6.5 kg d−1 in the Main, 34.1 kg d−1 in the Oder, and 134.5 kg d−1 in the Rhine River. In all of the sampled rivers, concentrations of 1,4-dioxane increased with distance from the mouth of the river and were found to negatively correlate with the discharge of the river. In order to determine if 1,4-dioxane can reach drinking water supplies, samples from a Rhine River bank filtration site and potable water from two drinking water production facilities were analyzed for the presence of 1,4-dioxane in the raw water and finished potable water. The raw water (following bank filtration) contained 650 ng L−1 to 670 ng L−1 of 1,4-dioxane, whereas the concentration in the finished drinking water fell only to 600 ng L−1 and 490 ng L−1, respectively.
During the final project, investigations of the source identification of high glyme concentrations in the Oder River were carried out. During four sampling campaigns between January, 2012 and April, 2013, 50 samples from the Oder River in the Oderbruch region and Poland were collected. During the first two samplings in the Oderbruch polder, glymes were detected at concentration reaching 0.07 µg L-1 (diglyme), 0.54 µg L−1 (triglyme) and 1.73 µg L−1 (tetraglyme) in the Oder River. The extensive sampling campaign of the Oder River (about 500 km) in Poland helped to identify the area of possible glyme entry into the river. During that sampling the maximum concentrations of triglyme and tetraglyme were 0.46 µg L−1 and 2.21 µg L−1, respectively. A closer investigation of the identified area of pollution, helped to determine the possible sources of glymes in the Oder River. Hence, the final sampling focused on the Kaczawa River, a left tributary of the Oder River and Czarna Woda, a left tributary of Kaczawa River. Moreover, samples from an industrial wastewater treatment plant were collected. Samples from Czarna Woda stream and Kaczawa River contained even higher concentrations of diglyme, triglyme, and tetraglyme, reaching 5.18 µg L−1, 12.87 µg L−1 and 80.81 µg L−1, respectively. Finally, three water samples from a wastewater treatment plant receiving influents from a copper smelter were analyzed. Diglyme, triglyme, and tetraglyme were present at an average concentration of 569 µg L−1, 4300 µg L−1, and 65900 µg L−1, respectively in the wastewater. Further research helped to identify the source of the glymes in the wastewater. The gas desulfurization process – Solinox implemented in the nearby copper smelter uses glymes as physical absorption medium for sulfur dioxide.
Results of this doctoral research provide important information about the occurrence, distribution, and behavior of hydrophilic ethers: 1,4-dioxane, monoglyme, diglyme, triglyme, and tetraglyme in the aquatic environment. A method capable of analyzing a wide range of ether compounds: from a volatile ETBE to a high molecular weight tetraglyme was validated. 1,4-Dioxane and tetraglyme were found to be applicable as organic tracers, since they are not easily attenuated during bank filtration and the anoxic groundwater passage. The extent of water pollution with 1,4-dioxane was shown in waste-, surface-, ground-, and drinking waters. One source of extremely high concentrations of 1,4-dioxane in a municipal sewage treatment plant applying postanoxic denitrification was identified, however more information is needed on the entry of 1,4-dioxane into surface waters. Moreover, 1,4-dioxane was present in drinking water samples from river bank filtration, which demonstrates its persistence in the aquatic environment and its low degradation potential during bank filtration and subsequent water treatment. Furthermore, this was the first study that focused primarily on identifying sources of glymes in surface waters. Glymes find a widespread use in industrial sectors, hence establishing their origin in the surface water is difficult (as with 1,4-dioxane). In this work, a gas desulphurization process was identified to be a dominating source of glyme pollution in the Oder River.
This thesis aims to analyse in a first step the physical and chemical properties of soil profiles along pedomorphological transects in different land used conditions (protected, partly protected as well as cultivated and pastured areas) in North West Benin and in South East Burkina Faso. The information about soils, which are carried out in consideration of the pedogenesis processes like weathering types, saprolitisation, formation of laterite crusts and denudation within the planation surfaces are therefore correlated in a second step with the structure and dynamic of woody plant around individual soil profiles. The relationship soil properties and woody plant is investigated in order to assess the reciprocal influence between the diversity of woody plants and soil characteristics within a small scale study and under different land use conditions.
A common vertical and lateral differentiation of physical and chemical properties regardless of the partly protected, protected and cultivated status of the sites can be noticed. Thus, in the cultivated site of Kikideni and in the partly protected zone of Natiabouani (South East Burkina Faso) sandy loam and sandy clay loam soil surfaces are widespread because of the occurrence of similar erosion processes like sheet wash, rill and gully erosion while in the central part of the Pendjari National Park loamy soil textures are prevailing. In fact, the steepness of the relief and the length of the slopes in the Pendjari Park seem to limit the development of some erosion forms as gully. Furthermore, the classification of soils reflects the variation of pedological processes along the transects and thus the occurrence of different soil types. The status of the sites may play an insignificant role in the differentiation of soil properties within the scale of small pedomorphological transects. A direct comparison of the vegetation type in the land use respectively partly protected and in the total protected sites (National Park of Pendjari) reveals a transition from the shrub savanna to the tree savanna. In conclusion it is important to insist on the fact that the variations of soil parameters within small slopes and the different sites are more conditioned by varying erosion processes and drainage conditions than the status protected or land use sites while the composition and diversity of plants is influenced by the status of the sites, the prevailing management tools, the pedogenetic conditions as well as the presence of wild animals like elephants. The ordination diagram shows that the organic matter is better correlated to the subgroup representing principally the sites of the hunting zone of the Pendjari Park and might be an explaining factor to the distribution of these sample sites groups. CEC ratios in the partly protected site of Natiabouani represent the highest measured in all sites. Nevertheless, statistical analysis of the CCA (canonical correspondence analysis) indicates generally a low correlation. This tendency is consolidated by the Monte Carlo test (p=0.14) which is a good indicator of species and environmental conditions. The detailed analysis of soil properties and the vegetation dynamic as well as their relationship within small pedomorphological transects represent an important pedological and botanical data collection involving different compartments. This thesis contributes to the better understanding of the savanna landscapes of West Africa and may provide essential scientific background for each development project directed towards interdisciplinary and integrative researches.
In dieser Arbeit wird die Richtungsabhängigkeit seismischer Geschwindigkeiten im Erdmantel unterhalb Deutschlands und angrenzender Gebiete durch die Analyse der teleseismischen Kernphase SKS auf Doppelbrechung untersucht (Scherwellen-Splitting). Die Anisotropie wird durch die Splittingparameter Φ und δt beschrieben und erlaubt Rückschlüsse auf geodynamische Prozesse.
Untersucht werden Aufzeichnungen des Deutschen Seismologischen Regionalnetzes (GRSN) und assoziierter Stationen aus dem Zeitraum von 1993 bis 2009. Für drei Stationen des Gräfenberg-Arrays (GRF-Array) sind Wellenformen ab 1976 verfügbar, welche damit einen weltweit einmaligen Datensatz liefern.
Auf Grund des stetigen Ausbaus der seismologischen Netze und des langen Beobachtungszeitraumes können über 3.000 Seismogramme ausgewertet werden. Der Hauptteil dieser Arbeit besteht daher in der Entwicklung einer automatischen Methodik zur Analyse von SKS-Splitting: ADORE ("Automatische Bestimmung von DOppelbrechnungsparametern in REgionalseismischen Netzwerken"). Für regionale Netze wie das GRSN gewährleistet ADORE eine objektive Bestimmung der Splittingparameter. Zunächst wird das seismologische Netzwerk als seismisches Array aufgefasst, um durch eine Frequenz-Wellenzahl-Analyse den Einsatz der SKS-Phase ohne manuellen Eingriff zu bestimmen. Die Berechnung der Splittingparameter erfolgt durch eine Inversion nach der Methode der Minimierung des transversalen Energieanteils. Automatisch wird das optimale Fenster um den SKS-Einsatz positioniert, für jede Beben-Stations-Kombination werden dazu 3.600 Einzelinversionen durchgeführt.
Um diese Vielzahl von Auswertungen in akzeptabler Zeit zu berechnen, nutzt ADORE moderne Rechnerarchitekturen aus, verteilt die Berechnungen auf mehrere Computer im lokalen Netzwerk und erzielt damit eine Beschleunigung um einen Faktor 60.
Die Analyse des gesamten Datensatzes ergibt folgende Ergebnisse: An allen analysierten Stationen wurde ein Scherwellen-Splitting festgestellt, der Stationsuntergrund weist somit überall Anisotropie auf. Für 240 Erdbeben können insgesamt 494 Wertepaare mit höchster Qualität bestimmt werden.
Unter der Annahme einer homogenen ungeneigten anisotropen Schicht unterhalb der jeweiligen Station können die Einzelmessungen pro Station gemittelt werden. Damit sind Regionen mit ähnlichen Merkmalen gut zu identifizieren: Im Norden Deutschlands herrschen NW-SO-, in der Mitte W-O-Richtungen und im Süden SW-NO-Richtungen vor.
Die Verzögerungszeiten liegen im Bereich zwischen 1.0 (Station Taunus) und 2.2 Sekunden (Tannenbergsthal, TANN). Auf Grund des hohen Wertes sind die Ursachen für die hier beobachteten Zeiten dem Erdmantel und nicht der Kruste zuzuordnen. Die bevorzugte Ausrichtung von anisotropen Kristallen auf Grund von Fließprozessen von Mantelmaterial ist Quelle der beobachteten Anisotropie. Rezente Fließprozesse von Mantelmaterial sind vor allem an der Unterkante der Lithosphäre wahrscheinlich. Durch Gebirgsbildungsprozesse, vorhandene Gebirgswurzeln oder regionale Veränderungen in der Mächtigkeit der Lithosphäre entstehen Barrieren für viskoses Mantelmaterial.
Als tektonische Ursachen für die hier gemessenen Orientierungen ist im Norden die Tornquist-Teisseyre-Linie (TTZ), in der Mitte die Variszische Gebirgsbildung und im Süden Einflüsse des Alpenbogens anzusehen. Ausnahmen bilden die Stationen Clausthal-Zellerfeld (CLZ), Rügen und Black-Forest-Observatory (BFO). Während bei letzterer ein Einfluss der Spreizungszone des Oberrheingrabens zu vermuten ist, scheint die Intrusion des Brockengranits die Beobachtungen an CLZ zu prägen. Rügen liegt in einer Übergangszone zwischen Sorgenfrei-Tornquist-Zone und TTZ.
Durch die Vielzahl von vorhandenen Einzelmessungen lassen sich an manchen Stationen komplexe Modelle untersuchen. Dazu zählen neben Gradientmodellen auch die geneigte Schicht und Zwei-Schicht-Modelle. Für sechs Stationen kann ein Zwei-Schicht-Modell erstellt werden: BFO, Gräfenberg A1, Fürstenfeldbruck (FUR), Rüdersdorf (RUE), TANN und Unterbreitzbach (UBBA). Die Interpretation der Richtungen von oberer und unterer Schicht gelingt für einen Teil der genannten Stationen: An BFO liegt die Orientierung der unteren Schicht parallel zur Vorzugsrichtung der variszischen Gebirgsbildung, jene der obere Schicht antiparallel zur Spreizungsrichtung des Rheingrabens. Für die Station FUR ist eine Überlagerung mit der Streichrichtung des Alpenmassivs zu beobachten. An GRA1 wird die untere Schicht offenbar durch rezente oder eingefrorene Anisotropie des Böhmischen Massivs bzw. des Eger-Riftsystems beeinflusst. Eine vergleichbare Wirkung ist durch die TTZ an der Station RUE zu erkennen.
ADORE wurde weiterhin auf einen Datensatz des temporären RIFTLINK-Projektes angewandt.
Forty two samples of the Late Eocene Kiliran oil shale, Central Sumatra Basin, Indonesia were collected from a 102 m long drill core. Palynofacies and geochemical analyses have been carried out to reconstruct the paleoenvironmental conditions and paleoecology during deposition of the oil shale. Amorphous organic matter (AOM) is very abundant (>76%). B. braunii palynomorph is present (3-16%) as the only autochtonous structured organic matter and generally more abundant in middle part of the profile. The stable carbon isotopic composition of organic matter (δ13C) varies from -27.0 to -30.5‰ and is generally more depleted in middle part of the profile. The ratio of total organic carbon to sulfur (TOC/S), used as salinity indicator, ranges from 2.5 to 15.8 and shows variations along the profile. Relatively less saline environments are observed in the middle part profile. Fungal remains are generally present only in middle part of the profile with distinct peak of abundances. The presence of fungal remains is regarded as an indication for a relatively warmer climate during deposition of middle part of the profile. The warmer climate is thought to influence the establishment of a thermocline, limiting the supply of recycled nutrients to the epilimnion. Consequently, the primary productivity in the Kiliran lake decreased during deposition of the middle part of the profile as indicated by the relatively depleted δ13C and the blooming of B. braunii. The chemocline was also shoaling during deposition of the middle part of the profile according to the higher abundance of isorenieratene derivatives of green sulfur bacteria origin. The warmer climate affected also to increase of water supply and thus less saline environments.
Tectonic subsidence is also thought to be a significant factor for the development of the Kiliran lake. The Zr/Rb ratio, an indicator for grain size, ranges from 0.4 to 1.3 and generally increases upwards along the profile. Three sudden decreases of the ratio are observed, indicating rapid change to finer grain size. These decreases are interpreted to indicate rapid deepening events of the lake due to mainly periodic subsidence. During deposition of lower part of the profile, the subsidence rates might have been relatively higher than sediment and water supply rates, resulting in a higher autochtonous fraction in the oil shale. During deposition of middle part of the profile, the sediment and water supply rates were relatively higher promoting distinct progradational sedimentation. Subsequently, the lake became more shallow and smaller during deposition of the upper part of the profile, leading to a relatively higher terrigenous input to the oil shale.
Norneohop-13(18)-ene and neohop-13(18)-ene derived from methanotrophic bacteria are the dominant hopanoid hydrocarbons. The sum of their concentrations varies from 40.6 to 360.0 μg/g TOC. The δ13C of these compounds are extremely depleted (-45.2 to -50.2‰). The occurrence of abundant bacteria including methanotrophic bacteria was responsible for the recycling of carbon below the chemocline of the lake. The effect of the recycling of carbon is observed by the presence of a concomitant depletion (about 7-9‰) in 13C of some specific biomarkers derived from organisms dwelling in the whole phototrophic zone.
4-Methylsterane and 4-methyldiasterene homologues occur in the oil shale as the predominant biomarkers. The sum of the concentrations of all homologues are about 40.3-1,009.2 μg/g TOC with generally higher values in uppermost and lower parts of the profile. Ca accounts as the predominant element in the oil shale, ranging from 5.0 to 16.7%. This element shows generally parallel variation with the 4-methylsterane homologues along the profile. This suggests that the 4-methylsteranes were derived from biological sources favoring more alkaline and more trophic environments. On the other hand, these compounds were less abundant in middle part of the profile which is consistent with less alkaline and less trophic environments promoting B. braunii to bloom.
The 4-methylsterane homologues are considered to originate from Dinoflagellates. Alternation between Dinoflagellates and B. braunii in Paleogene lake systems due to water chemistry changes are known from previous studies. Moreover, freshwater Dinoflagellates have been frequently reported to occur in the basin depocenters. In the present case, distinct alternation between B. braunii abundances and concentrations of 4-methylsterane homologues along the studied oil shale profile suggest that the 4-methylsterane homologues were derived from freshwater Dinoflagellates although dinosterane is not present in the sediment extracts. Water alkalinity and trophic level changes were most likely responsible for the alternation of Dinoflagellates and B. braunii blooming.
The mantle xenoliths collected by kimberlites indicate that the subcratonic mantle underneath the Archean crust is mostly a residue of high degrees of partial melting which was subsequently reenriched. The majority of the xenoliths show cryptic metasomatism and only few modal metasomatism.
Much effort has been put into deciphering different kinds of enrichment processes within the mantle. Here, we take the approach to look into the inventory of subcalcic garnets which stem from cpx-free harzburgites and dunites. These subcalcic garnets, commonly with sinusoidal REE patterns, carry the major budget of the trace elements of their host rock. Thus, they are promising objects to study both depletion and enrichment. Most importantly, the analysis of a single grain subcalcic garnetwill provide almost all important information of the bulk rock. Our aim is to gain detailed information mainly on metasomatism on a craton wide scale by combining major, trace elements and Lu-Hf and Sm-Nd isotopic signatures from subcalcic garnets. Eventually, we will summarize the metasomatic agent(s) and processes and possibly the timing of the enrichment within the lithospheric mantle underneath the Kaapvaal craton.
This research was conducted in the Rwenzori Region of the Western Branch, East African Rift System (EARS). The EARS is a tectonic structure extending over a length of more than 3000 km from the Afar Triple Junction, in Ethiopia, to Lake Malawi in the south. The Western Rift System is a roughly NE to ENE trending sector of the EARS, which runs along the western boundary of Uganda and the neighboring Democratic Republic of Congo (D.R.C). It stretches 2100 km from Nimule, NW on Uganda-Sudan border, extending to Lake Malawi in the SE of Africa. The unusual uplift of the Rwenzori Mountains within an extensional regime and the mechanisms associated with the high frequency of seismic activity in the region was hardly understood and therefore, had remained a subject of contention that needed to be critically addressed in detail. To my knowledge, this was probably the first study to be performed and documented in great depth within the domains of seismic noise variation, seismic anisotropy and b value analyses beneath the Rwenzori Region. After about six years of operation (2006-2012), the seismology group of the RIFTLINK Research Project (www.riftlink.org) acquired a vast amount of high-quality, digital data that were collected using a seismic network of well calibrated seismic equipment. The project was divided into two phases. Phase I, that operated between February 2006 - September 2007, consisted of thirty-two temporary seismic stations, which were selectively spread out in the Rwenzori Region on the Ugandan side, to detect and record extremely weak as well as strong naturally occurring earthquakes. The seismic equipment used included EDL and REFTEK digitizers, which were coupled with Güralp and MARK sensors respectively (REFTEKS: only short-period MARK sensors, EDLs: short-period MARK plus few broadband Güralp Sensors). Exactly 22375 earthquakes were recorded. The data were processed using the SEISAN software package. About 14413 earthquakes were carefully localized using the velocity model of Bram (1975) that implements a Vp=Vs ratio fixed at 1.74. Phase II, that extended between 2009-2012 consisted of thirty-two seismic stations, which were spread out around the Rwenzori Mountains, both on the Ugandan side and the neighboring D.R.C. Only Taurus digitizers that were coupled with Trillium sensors were used in the D.R.C. On the Ugandan side however, both EDL and Taurus digitizers, which were coupled with Trillium and Güralp sensors were used. ...
Die vorliegende Arbeit wurde im Rahmen des Forschungsprojekts „Integrierte Analyse von mobilen, organischen Fremdstoffen in Fließgewässern“ (INTAFERE) am Institut für Physische Geographie an der Goethe-Universität Frankfurt erstellt. In INTAFERE wurde das Gefährdungspotenzial von mobilen, organischen Fremdstoffen (MOF) für aquatische Ökosysteme und die natürlichen Wasserressourcen in integrierter und partizipativer Art und Weise untersucht. MOF sind chemische Substanzen, die in Alltagsprodukten enthalten sind und durch unterschiedliche Eintragsfade in unbekannten Mengen in Oberflächengewässer eingetragen werden. Problematisch sind aus Umweltgesichtspunkten ihre Eigenschaften: sie besitzen im Wasser eine hohe Mobilität und sind schwer abbaubar. Dies führt zu einer Persistenz über lange Zeiträume. Für einige dieser Substanzen wurde zudem gezeigt, dass sie in sehr geringen Konzentrationen biologisch aktiv sind und für aquatische Ökosysteme eine Gefahr darstellen. In INTAFERE wurden drei zentrale Ziele verfolgt: Charakterisierung des Problemfeldes MOF, Erzeugung von praxisrelevantem Wissen für das Management von MOF und Entwicklung einer Softwareanwendung, die gesellschaftliche Aushandlungsprozesse durch eine transparente Darstellung der Wirkungszusammenhänge im Problemfeld unterstützt. Um einen Beitrag für die Erfüllung der Ziele zu leisten, war es die Aufgabe der Verfasserin, eine Akteursanalyse und -modellierung durchzuführen sowie Zukunftsszenarien im Bereich der MOF zu entwickeln. Dafür existierte keine adäquate Methodik, daher verfolgt die Dissertation zum einen die Entwicklung einer Methodik und zum anderen deren Anwendung im Kontext des Projektes INTAFERE. Da im Forschungsprozess die Durchführung von Analysen, die wissenschaftliche und gesellschaftliche Sichtweise der Problematik sowie die Erarbeitung von praktischen Lösungen im Mittelpunkt standen, wurde eine transdisziplinäre Herangehensweise gewählt. Ziel war es, eine Methodik zu entwerfen, die sowohl eine Entwicklung von Szenarien als auch eine Modellierung von Handlungsentscheidungen umfasst. Eine Modellierung und Visualisierung von Handlungsentscheidungen ist notwendig, um Strategien für ein Umweltproblem für verschiedene Szenarien zu ermitteln, und damit einen Lernprozess der Stakeholder zu initiieren. Dies wurde mit der transdisziplinären Methode „Akteursbasierte Modellierung“ umgesetzt. Hierbei wurden insbesondere Aspekte der Problemwahrnehmung von Akteuren und deren Darstellung, der partizipativen Szenarienentwicklung sowie der semi-quantitativen Modellierung von Handlungsentscheidungen berücksichtigt. Die Verfasserin hat mit der semi-quantitativen akteursbasierten Modellierung eine Methode erarbeitet und getestet, die bisher unverbundene Komponenten (wie die Software Dynamic Actor Network Analysis (DANA) und die Szenarienentwicklung) zusammenführt. Um Handlungsentscheidungen unter verschiedenen Szenarien zu modellieren hat die Autorin eine sequentielle Modellierung entwickelt, die mit der Software DANA durchgeführt werden kann. Die dafür notwendige Weiterentwicklung von DANA wurde von Dr. Pieter Bots (TU Delft) umgesetzt. Die akteursbasierte Modellierung läuft in drei methodischen Schritten ab: 1. Modellierung von Akteurs-Sichtweisen in Form von Wahrnehmungsgraphen und deren Analyse, aufbauend auf Ergebnissen von qualitativen, leitfaden-gestützten Expertengesprächen (= Akteursmodellierung), 2. partizipative Szenarienentwicklung mit den Akteuren und 3. Zusammenführung der Ergebnisse der Akteursmodellierung und der Szenarienentwicklung und darauf aufbauend eine sequentielle Modellierung von Handlungsentscheidungen und deren Auswirkungen auf Schlüsselfaktoren. Im Zuge der Anwendung auf das Problemfeld der MOF wurde für folgende Akteure jeweils ein Wahrnehmungsgraph modelliert: Obere Wasserbehörde, Umweltbundesamt, Umwelt- und Verbraucherschutzorganisationen, Wasserversorger sowie für die Hersteller von verschiedenen MOF, weiterhin für die European Flame Retardants Association und die Weiterverarbeitende Industrie. Das Ergebnis der Szenarienentwicklung waren vier Szenarien: ein Gesundheitsszenario, unter der Annahme von hohen lokalen Umweltstandards durch nachhaltigkeitsorientierte KonsumentInnen, ein Umweltszenario, in dem eine starke Regulierung und nachhaltigkeitsorientierter Konsum Hand in Hand gehen, ein Globalisierungsszenario, in dem Wirtschaftsmacht und preisbewusste KonsumentInnen statt staatliche Regulierung vorherrschen und ein Technikszenario, unter der Annahme, dass Kläranlagen, bedingt durch eine starke Regulierung, aufgerüstet werden. Bei der Modellierung von Handlungsentscheidungen wurden die Wahrnehmungsgraphen und die vier Szenarien miteinander verknüpft. Pro Substanz wurde ein Modell entwickelt, welches die wichtigsten Systemkomponenten in einer angemessenen Komplexität umfasst und die von den Akteuren gemeinsam getragene Einschätzung der Wirkungsbeziehungen darstellt. Insgesamt wurden 16 Modelle entwickelt. Basierend auf den simulierten Akteurshandlungen wurden relativen Veränderungen der Schlüsselfaktoren Produktion, Import und Leistungsfähigkeit der Kläranlagen für die vier genannten Szenarien berechnet. In Zusammenarbeit mit Pieter Bots konnten algorithmische Beiträge zur Analyse- und Modellierungssoftware DANA getestet und verbessert werden. Da keine vollständige und zugleich leicht verständliche Einführung zu DANA vorlag, wurde für Nutzer im Rahmen dieser Dissertation eine Anleitung verfasst, die die Modellierung von Wahrnehmungsgraphen und deren Analyse sowie alle Schritte der akteursbasierten Modellierung mit DANA erläutert.
In dieser Arbeit werden Schmelz- und Anreicherungsprozesse des Erdmantels, sowie Kristallisationsereignisse der Erdkruste zweier ausgewählter Gebiete in Namibia und Spanien mithilfe geochemischer Methoden rekonstruiert und in einen zeitlichen Zusammenhang gebracht. Ein Vergleich der gewonnenen Ergebnisse beider Kompartimente soll dabei weitere Informationen liefern inwieweit Prozesse des Erdmantels und der Erdkruste miteinander verknüpft waren. Insbesondere soll ein weitere Beitrag zur aktuellen Diskussion geliefert werden, bei der sich das sogenannte „pulsed growth“ und „steady accumulation“ Modell gegenüberstehen (siehe Zusammenstellung Pearson et al., 2007). Zudem tragen die neu gewonnenen Daten dazu bei, die regionalen geologischen Gegebenheiten im besonderen Hinblick auf die geotektonische Geschichte besser zu verstehen.
Das Gibeon Kimberlit Feld befindet sich in der tektonischen Einheit des Rehoboth Terranes in Namibia und ist gekennzeichnet von Vulkanismus vor etwa 72.5 Ma (Davies et al., 2001), der Granat Peridotite und krustale Xenolithe mit an die Oberfläche beförderte. Eine klare Einordnung des Rehoboth Terranes in die Gesamtheit des Süd Afrikanischen Plattenverbunds ist noch nicht vollständig geklärt.
Die Südöstliche vulkanische Provinz in Spanien (SEVP) mit besonderem Hinblick auf die Region um Casas de Tallante stellt das zweite Probengebiet für diese Arbeit dar. Vor etwa 2.6 Ma (Bellon et al., 1983) kam es zur Extrusion von alkali-basaltischen Schmelzen, die zahlreiche Spinell / Plagioklas Peridotite mit sich brachten. Tufflagen, sowie die Matrix der Basalte ermöglichen einen Einblick in die untere Kruste der Region.
Untersuchungen der Erdmantelproben aus Namibia auf ihre Haupt- und Spurenelementchemie, sowie Lu-Hf und Sm-Nd Isotopie zeigten, dass zwei verschiedene Manteltypen vorliegen („N“ und „σ“ Typ), die zu einem Zeitpunkt um etwa 850 Ma („N“) und 1.9 Ga („σ“) angereichert wurden. Eine letzte Anreicherung beider Typen fand vermutlich während der Pan–Afrikanischen Orogenese um etwa 450 Ma statt. Die Reinterpretation eines zuvor publizierten Datensatzes (Pearson et al., 2004), suggeriert, dass es zu einer ersten Verarmung der σ Peridotite um etwa 2.9 Ga kam.
Untersuchungen der U-Pb und Hf Isotopie an Zirkonen aus der unteren Kruste des Probengebiets in Namibia ergaben, dass es zur Bildung von juvenilem Krustenmaterial vermutlich bereits im Archaikum kam (wie bereits vorgeschlagen durch z.B. Hoal et al., 1995; Franz et al., 1996), sowie in den Zeiträumen von 2.3 bis 2.7 und 1.5 bis 1.6 Ga, mit jeweils anschließendem krustalem Recycling und Krustenmischung. Eine Übereinstimmung von Mantel- und Krustenevents konnte für die Zeiträume von etwa 1.8, 0.8 - 0.9 Ga und 0.4 – 0.5 Ga gefunden werden. Eine mögliche erste Verarmung des σ Mantels wird bestätigt durch Zirkonalter im Bereich von 2.7 bis 2.9 Ga.
Die Analyse ausgewählter Spinell / Plagioklas Peridotite aus der SEVP, ergaben, dass ein heterogener Mantel mit mindestens 3 verschiedenen Typen vorliegt. Eine Korrelation der Lu-Hf Isotopie von 3 Proben dieses Probensatzes, sowie den Hf Isotopien einer weiteren Probe von Bianchini et al. (2011) suggerieren, dass es eventuell zu einem Verarmungsereignis zu einem Zeitpunkt von etwa 550 Ma kam. Sr Isotopien von Klinopyroxenen und Plagioklasen im Vergleich ergaben, dass die Sr Isotopie der Plagioklase, im Gegensatz zu den Klinopyroxenen, von denen der Alkali Basalte überprägt wurden.
Zirkonanalysen aus Lokalitäten innerhalb der SEVP (U-Pb, Hf) ergaben ein weitreichendes Altersspektrum, beginnend bei etwa 2-3 Ma bis hin ins Archaikum (2.7 bis 2.9 Ga) mit Provenance Ursprung aus Gondwana und dem Arabisch-Nubischen Schild. Die Kombination der U-Pb Altersinformationen mit den entsprechenden Hf Isotopien, zeigten, dass es vermutlich bereits im Archaikum zu juveniler Krustenbildung kam. Zirkone > 100 µm datieren den Zeitpunkt der Eruption der Alkali Basalte mit Altern um etwa 2.6 Ma und Hf Isotopien, die einem leicht verarmten Mantel entsprechen. Ein mögliches Verarmungsereignis im Erdmantel zu einem Zeitpunkt von etwa 550 Ma, ist im Einklang mit Krustenrecycling zu selbigem Zeitpunkt.
Die neugewonnenen Daten dieser Arbeit unterstützten das „pulsed growth“ Modell.
Literatur
Bellon, H., Bordet, P. and Montenat, C., 1983. Chronology of the Neogene Magmatism from Betic Ranges (Southern Spain). Bulletin De La Societe Geologique De France, 25(2): 205-217.
Bianchini, G., Beccaluva, L., Nowell, G.M., Pearson, D.G. and Siena, F., 2011. Mantle xenoliths from Tallante (Betic Cordillera): Insights into the multi-stage evolution of the south Iberian lithosphere. Lithos, 124(3-4): 308-318.
Davies, G.R., Spriggs, A.J. and Nixon, P.H., 2001. A non-cognate origin for the Gibeon kimberlite megacryst suite, Namibia: Implications for the origin of Namibian kimberlites. Journal of Petrology, 42(1): 159-172.
Franz, L., Brey, G.P. and Okrusch, M., 1996b. Steady state geotherm, thermal disturbances, and tectonic development of the lower lithosphere underneath the Gibeon Kimberlite Province, Namibia. Contributions to Mineralogy and Petrology, 126(1-2): 181-198.
Hoal, B.G., Hoal, K.E.O., Boyd, F.R. and Pearson, D.G., 1995. Age constraints on crustal and mantle lithosphere beneath the Gibeon kimberlite field, Namibia. South African Journal of Geology, 98(2): 112-118.
Pearson, D.G., Irvine, G.J., Ionov, D.A., Boyd, F.R. and Dreibus, G.E., 2004. Re-Os isotope systematics and platinum group element fractionation during mantle melt extraction: a study of massif and xenolith peridotite suites. Chemical Geology, 208(1-4): 29-59.
Pearson, D.G., Parman, S.W. and Nowell, G.M., 2007. A link between large mantle melting events and continent growth seen in osmium isotopes. Nature, 449(7159): 202-205.
Die Wechselwirkung zwischen zwei verschiedenartigen Wellenphänomenen in einer Höhe von ca. 10 bis 100 km, der mittleren Atmosphäre, ist das zentrale Thema der vorliegenden Arbeit. Schwerewellen entstehen durch Oszillationen der Luft in einer stabil geschichteten Atmosphäre. Durch die Vielzahl von Schwerewellen-Paketen, die in der Troposphäre durch Gebirge, Gewitter, Fronten und andere dynamische Prozesse angeregt werden, wird Energie und Impuls in die mittleren Atmosphäre transportiert. Durch den turbulenten Zerfall von brechenden Schwerewellen wird auf die mittlere Strömung eine Kraft ausgeübt, welche im Bereich der Mesopause bei ca. 90 km maximal wird. Daraus resultiert die sogenannte interhemispherische residuelle Zirkulation, die in der Mesosphäre den Sommer- mit dem Winterpol verbindet und die beeindruckend kalte Sommer-Mesopause mit Temperaturen von unter −140°C verursacht. Thermische Gezeiten sind ein weiterer wichtiger Teil in der Dynamik der mittleren Atmosphäre. Sie werden durch die Erwärmung der Tagseite der Erde angeregt und sind globale Schwingungen mit Perioden von 24 Stunden und harmonischen Vielfachen. Mit Wind- und Temperatur-Amplituden von bis zu 50 m/s und 30 K dominieren sie die Tagesvariabilität im Mesopausen-Bereich.
In der Mesosphäre wird die Wechselwirkung zwischen Schwerewellen und thermischen Gezeiten wichtig. Dort wird durch die Gezeitenwinde das Brechen von Schwerewellen zeitlich moduliert und eine periodische Kraft erzeugt, welche auf die Gezeiten rückwirkt. Doch selbst unter Zuhilfenahme modernster Hochleistungsrechner kann in komplexen Zirkulationsmodellen nur ein Bruchteil des turbulenten sowie des Wellen-Spektrums aufgelöst werden. Der Effekt der nichtaufgelösten Skalen, wie Turbulenz und Schwerewellen, muss somit in effizienter Weise parametrisiert werden. Üblicherweise wird in Schwerewellen-Parametrisierungen die horizontale und zeitliche Variation des Hintergrundmediums vernachlässigt. Es entsteht eine vertikale Säule, in der sich stationäre Schwerewellen-Züge instantan nach oben ausbreiten. Es ist jedoch äußerst fraglich, inwieweit eine solche Beschreibung, auf der ein Großteil früherer Untersuchungen basiert, für das Ergründen der Schwerewellen-Gezeiten-Wechselwirkung hinreicht. Für diese Arbeit wurde deswegen das Ziel gesetzt, die Defizite der konventionellen Beschreibung der Schwerewellen-Ausbreitung in realistischen Gezeiten zu quantifizieren.
Die "Ray Tracing"-Methode wird auf die Problemstellung der Schwerewellen-Gezeiten-Wechselwirkung angewendet. In der "Ray Tracing"-Methode werden Schwerewellen-Pakete entlang ihrer Ausbreitungspfade explizit verfolgt und Veränderungen der Schwerewellen-Eigenschaften durch den Einfluss der Hintergrundströmung berücksichtigt. Vom Autor wurde das globale "Ray Tracing"-Modell RAPAGI (RAy PArameterization of Gravity-wave Impacts) entwickelt und mit realistischen Gezeitenfeldern aus dem Zirkulationsmodell HAMMONIA (HAmburg MOdel of the Neutral and Ionized Atmosphere) betrieben. In verschiedenen "Ray Tracing"-Experimenten wird für ein einfaches Schwerewellen-Ensemble gezeigt, wie horizontale Gradienten des Hintergrundmediums sowie dessen Zeitabhängigkeit wesentlichen Einfluss auf die Ausbreitung und Dissipation von Schwerewellen nehmen. Zum einen führt die durch Gezeitenwellen hervorgerufene Transienz zu einer tageszeitlichen Modulation der absoluten Schwerewellen-Frequenz.
Die dadurch induzierten Variationen der horizontalen Phasengeschwindigkeit der Schwerewellen können die anfängliche Phasengeschwindigkeit um bis zu eine Größenordnung übertreffen und folgen dem Verlauf des Hintergrundwindes. Die kritische Filterung von Schwerewellen wird durch diese Modulation abgeschwächt, was im Vergleich zu konventionellen Schwerewellen-Parametrisierungen zu einer im Mittel um 30 % geringeren Kraftwirkung auf die Gezeiten führt. Zum anderen werden durch horizontale Gradienten in der gesamten Hintergrundströmung Schwerewellen-Pakete horizontal abgelenkt. Wellen, die gegen die Hintergrundströmung laufen, werden in der Stratosphäre in die Maxima der Wind-Jets hineingeführt. Durch dieses Verhalten wird analog zum Fermatschen Prinzip der geometrischen Optik die Laufzeit der Schwerewellen in der mittleren Atmosphäre minimiert. Es entsteht eine Fokussierung von Schwerewellen-Feldern, bei gleichzeitiger Zunahme der horizontalen Wellenzahl in den Experimenten im Mittel um ca. 10 %. Dadurch reduziert sich der Schwerewellen-Impulsfluss und die mittlere und ebenfalls die periodische Kraft auf die Hintergrundströmung im Mittel um weitere 20 % bis 30 %. Konventionelle Schwerewellen-Parametrisierungen scheinen somit die Kraftwirkung von brechenden Schwerewellen zu uberschätzen. Aus den Ergebnissen der Arbeit wird klar, dass Schwerewellen-Parametrisierungen nicht "blind" für jede Untersuchung genutzt werden können. Alle Annahmen und Näherungen in Parametrisierungen müssen je nach Zielstellung neu getestet werden.
Occurrence and sources of 2,4,7,9-tetramethyl-5-decyne-4,7-diol (TMDD) in the aquatic environment
(2011)
The aim of the present study was to identify the sources of 2,4,7,9-tetramethyl-5-decyne-4,7-diol (TMDD) into the aquatic environment and to investigate its occurrence in rivers and wastewater treatment plants (WWTPs). Therefore, TMDD was analyzed in 441 wastewater samples from influents and effluents of 27 municipal WWTPs, in 6 sludge samples, in 52 wastewater samples from 3 sewage systems of municipal WWTPs, in 489 surface samples from 24 rivers, in 9 wastewater samples of 3 paper-recycling industries and in 65 groundwater samples. TMDD was also analyzed in household paper products, in 23 samples of toilet
papers, in 5 types of paper towels and in 12 types of paper tissues. The samples were collected between 2007 and 2011. The water samples were extracted with solid phase extraction (SPE) and the household paper samples with Soxhlet extraction. Gas chromatography-mass spectrometry (GC-MS) was used for quantification purposes. Between November 2007 and January 2008, TMDD was detected in the river Rhine at Worms with permanent high concentrations (up to 1330 ng/L). The results showed that TMDD is uniformly distributed across the river at Worms. An increase of the mean TMDD concentration from approximately 500 ng/L to 1000 ng/L was registered in January 2008. Due to the minor fluctuations of the TMDD concentration during the sampling period it is expected that the input of TMDD into the river is continuous. Therefore, TMDD might rather originate from effluents of municipal WWTPs than from temporal sources. The mean TMDD load based on the analysis of 147 water samples collected in the River Rhine was 62.8 kg/d which is equivalent to 23 t/a suggesting that TMDD must be used and/or produced in high quantities in order to be found in those high concentrations. To determine if TMDD is discharged by effluents of municipal WWTPs into the rivers, 24 hours influent and effluent samples of four municipal WWTPs in the Frankfurt/Rhine-Main metropolitan region were collected during November 2008 and February 2010 and analyzed for TMDD. The TMDD influent concentrations varied between 134 ng/L and 5846 ng/L and the effluent concentrations between <LOQ (limit of quantitation) and 3539 ng/L. The TMDD elimination rates in the four WWTPs varied between 33% and 68%. The results showed that effluents of municipal WWTPs are an important source of TMDD in the aquatic environment because TMDD is not completely removed from the sewage during the wastewater treatment. Weekly and daily variations of the TMDD concentration in the influents of two municipal WWTPs indicated that both private households and indirect industrial dischargers contribute to the introduction of TMDD into the municipal sewage systems. A more detailed study of the TMDD elimination rate in the different wastewater treatment stages was carried out in the WWTP Niederrad/Griesheim in Frankfurt am Main. The results showed that the removal of TMDD is mainly carried out during the aerobic biological treatments, where the elimination rate was 46%. In contrast, during the anoxic treatment the removal efficiency was only 1.4% and during the mechanical treatment the elimination rate was 19%. To determine the sources of TMDD in the sewage, household paper products (paper tissues, toilet papers and paper towels) were analyzed for TMDD using Soxhlet extraction. TMDD was detected in 83% of the samples (n=40). The highest mean TMDD concentrations were found in recycled toilet paper (0.20 μg/g) and in paper towels (0.11 μg/g). In paper tissues and non-recycled toilet paper the mean TMDD concentrations were lower 0.080 μg/g and 0.025 μg/g respectively. According to these results the high TMDD influent concentrations found previously in municipal WWTPs (mean 1.20 μg/L) cannot be explained due to migration of TMDD from the household paper products into the sewage. Thus indirect industrial dischargers are the cause of the high influent TMDD concentrations. Effluents of municipal WWTPs with different indirect industrial dischargers (textile-, metal processing-, food processing-, electroplating-, paper-recycling- and printing ink factories) were analyzed. The highest mean TMDD concentrations were found in the effluents of municipal WWTPs that have paper-recycling (71.3 μg/L) and printing ink factories (138 μg/L) as indirect industrial dischargers. These results were confirmed by analyzing process wastewater of three paper-recycling factories located in Germany. High TMDD concentrations were detected and fluctuated between 1.83 μg/L and 113 μg/L. TMDD was also analyzed in the wastewater of a non-recycling-paper factory but its concentration was much lower (0.066 μg/L) indicating that TMDD is introduced into the processing water during the papermaking process due to the use of waste paper. Analyses of wastewater samples from different parts of the sewage pipes of a municipal WWTP in Hesse, which receives the wastewater from a printing ink factory, were carried out. The TMDD concentration in the wastewater sample from the sewage pipe of the printing ink factory was much higher (3,300 μg/L) than the TMDD concentration detected in the other wastewater samples from the sewage system (0.030 μg/L – 0.89 g/L). These results confirm the printing ink production as one of the principal sources of TMDD in the sewage. Analysis of surface water samples of the River Modau downstream from the effluent of the WWTP Nieder-Ramstadt showed TMDD concentrations of up to 28.0 μg/L. These high TMDD concentrations might be caused by the indirect wastewater discharges of a paint factory connected to the municipal sewage system. These results indicate that TMDD is introduced into the municipal WWTPs principally by indirect industrial dischargers and they are mainly paint and printing ink factories. The paper-recycling factories also represent an important source of TMDD in municipal WWTPs but indirectly. According to statements given by the representatives of two paper recycling factories neither TMDD or any other TMDD containing product is used or added during the papermaking process. Therefore, TMDD is washed out from the printing inks of the coloured waste paper and concentrated in the process wastewater in the closed water circuits of paper-recycling factories reaching rivers and municipal WWTPs. The occurrence and distribution of TMDD in surface waters in Germany was also studied. The results showed that TMDD is widely distributed across different rivers systems in the federal states of Hesse, North-Rhine-Westphalia, Bavaria, Baden-Wuerttemberg and Rhineland-Palatinate. In Hesse, TMDD was detected in the some of main rivers with mean concentrations of 812 ng/L (Schwarzbach, Hessian Ried), 374 ng/L (Kinzig), 393 ng/L (Main, at Frankfurt), 539 ng/L (Werra), 326 ng/L (Fulda), 151 ng/L (Emsbach) and 161 ng/L (Nidda). In small rivers (creeks) the mean TMDD concentrations varied between <LOQ (Diemel, Urselbach) and 1890 ng/L (Darmbach). The results showed that the TMDD concentrations in creeks are highly influenced by both effluents of WWTPs and by the distance between the sampling point and the nearest WWTP. Surface samples from sampling locations downstream from WWTPs dischargers showed higher TMDD concentrations (mean 518 ng/L) than sampling locations upstream from WWTPs dischargers (mean 35.1 ng/L). The behavior of TMDD during bank filtration was investigated at two locations, at a water utility company at the Lower River Rhine (urban area) and at the Oderbruch polder (rural area). The results indicated that TMDD is removed from the surface water by bank filtration at both sampling locations. The removal process is probably carried out in the first meters of the aquifer (hyporheic zone) by biodegradation processes, since TMDD does not tend to be absorbed by sediments and it was not found in the groundwater of monitoring wells. In groundwater samples from the Hessian Ried (n=23) TMDD was found only in five samples and the highest TMDD concentration was 135 ng/L. According to these results, TMDD does not represent a concern for drinking water in Germany, since it does not reach the groundwater with high concentrations and it has a low toxicity potential. The input of TMDD into the North Sea was estimated to be 60.7 t/a by considering the mean transported loads of TMDD by the River Rhine at Wesel (58.3 t/a) and Meuse in the Netherlands (2.40 t/a). The estimated discharge of TMDD by German municipal WWTPs (8.19 t/a) and paper-recycling factories (9.24 t/a) into rivers seems to be too low considering that the mean TMDD load in the River Rhine downstream from Wesel is 58.3 t/a. However, due to the high density of population and industries at the Lower Rhine it is expected that more relevant sources of TMDD are located along the Rhine River increasing the transported load. According to the results of this PhD project TMDD is a non-ionic surfactant contained in products, which are applied on surfaces (printing inks and paints) and has the potential to reach the aquatic environment. Therefore, TMDD should fulfill the requirement of a biodegradability of 80% established by the “Law on the Environmental Impact of Detergents and Cleaning Products” in Germany. However, due to the partial elimination rates of TMDD obtained in municipal WWTPs (between 33% and 68%) and to the absence of information about the execution of the biodegradation test on TMDD, it is unknown if TMDD is in accordance with this law. Otherwise, its use as surfactant in such products is questionable.
The aim of this study is a better understanding of radiation processes in regional climate models (RCMs) in order to quantify their impact and to reduce possible errors. A first important task in finding an answer to this question was to examine the accuracy of the components of the radiation budget in regional climate simulations. To this end, the simulated radiation budgets of two regional climate simulations for Europe were compared with a satellite-based reference. In the simulations with the RCM COSMO-CLM there were some serious under- and overestimations of short- and long-wave net radiation in Europe. However, taking into account the differences in the reference datasets, the results of the COSMO-CLM were quite satisfactory.
Using statistical methods, the influence of potential sources of uncertainties was estimated. Uncertainties in the cloud cover and surface albedo had a significant impact on uncertainties in short-wave net radiation, the explained variance of uncertainties in cloud cover was two to three times higher than that of uncertainties in surface albedo. Uncertainties in the cloud cover resulted in significant errors in the net long-wave radiation. However, the influence of uncertainties in soil temperature on errors in the long-wave radiation budget was low or even negligible. These results were confirmed in a comparison with simulations of the REMO and ALADIN regional climate models. It is reasonable to expect that a better parameterization of relatively simple parameters such as cloud cover and surface albedo is a means of significantly improving the simulation of radiation budget components in the COSMO-CLM.
An important question for the application of RCMs is to examine whether the results of radiation uncertainties and their impact factors are comparable if the model is applied in a region that is not the one for which it was originally created. Comparisons of the simulated radiation budgets of different RCMs for West Africa showed that problems in the simulation of short- and long-wave radiation fluxes were a widespread problem. Most of the tested models showed some considerable under- or overestimation of the short- and long-wave radiation fluxes.
Similar to Europe uncertainties in cloud cover were also in the simulations for Africa a significant factor affecting uncertainties in the simulated radiation fluxes. However, for the African simulations uncertainties in the parameterization of surface albedo were much more important than in Europe. On average, overland uncertainties in the cloud cover and surface albedo were of similar importance. Uncertainties in soil temperature simulations were of higher importance in Africa, and reached overland similar values of the mean explained variance (R2 ≈ 0.2) such as uncertainties in the cloud cover. This indicates a geographical dependence of the model error. This study confirmed the assumption that an improved parameterization of relatively simple parameters such as the surface albedo in RCMs leads to a significant improvement in the modeled radiation budget, particularly in Africa.
The influence of errors in the simulated radiation budget components on the simulation of climate processes, such as the West-African monsoon (WAM), was investigated in a next step. The evaluation of ERA-Interim and ECHAM5 driven COSMO-CLM simulations for Africa showed that the main features of the WAM were well reproduced by the model, but there were only slight improvements compared to the driving data. The index of convective activity in the model simulations was much too high and precipitation was underestimated in large parts of tropical Africa. The partly considerable differences between the ERA-Interim and ECHAM5 driven simulations demonstrated the sensitivity of the RCM to the boundary conditions and in particular to the sea surface temperature. An excessive northwards shift of the monsoon in the model was influenced by the land-sea temperature gradient and the strength of the Saharan heat low. Consequently, a part of the error was due to the driving data and the model itself produced another part.
By modifying the parameterization of the bare soil albedo the errors in the radiation budget and 2 m temperature in the Sahara region were significantly reduced. Similarly, the overesti-mation of precipitation and convection has been reduced in the Sahel. The effect of this modifi-cation on the examined WAM area was low. This confirmed that especially in desert regions, errors in the surface albedo were a driving factor for errors in the radiation budget. However, there are other important factors not yet sufficiently understood that have a strong influence on the quality of the simulation of the WAM.
The analysis of the actual state, the quantification of error sources and the highlighting of connections made it possible to find means to reduce uncertainties in the simulated radiation in RCMs and to have a better understanding of radiation processes. However, the magnitude of the errors found, the number of possible influencing factors, and the complexity of interactions, indicate that there is still a need for further research in this area.
Owing to long-term similarities with regard to orbital climate forcing (i.e., low eccentricity and a dampened influence of precession), Marine Isotope Stage (MIS) 11 represents one of the closest astronomical analogues for present and future climate. Hence, insights into the climate variability of MIS 11 can contribute to a better understanding of the climatic evolution of the present (Holocene) interglacial as it would occur without human interference. In order to elucidate the natural climate variability during MIS 11, this study examines predominantly annually laminated lake sediments of Holsteinian age from Dethlingen, northern Germany. The Holsteinian interglacial is widely accepted to be the terrestrial equivalent of MIS 11c in central Europe and can be biostratigraphically correlated with the Hoxnian, Mazovian and Praclaux interglacials on the British Isles, in Poland and in France, respectively. These correlations yield the potential to cross-check the results from individual sites on a regional scale. This study is based on a multi-proxy approach including palynological, micropaleontological, sedimentological, geochemical and time series analyses within a wellconstrained chronological framework that has been established through varve counting and regional bio-stratigraphic correlations with other annually laminated archives of Holsteinian age. In particular, the here-presented study aims at (i) fingerprinting the long-term (centennial- to millennial-scale) and short-term (sub-decadal- to decadal-scale) climate variability during the Holsteinian interglacial, (ii) deciphering the nature, tempo and trigger mechanisms of abrupt climate change under interglacial boundary conditions, and (iii) assessing its impact on terrestrial ecosystems. With regard to long-term climate variability, the vegetation succession at Dethlingen as inferred from pollen data provides insights into the mesocratic to telocratic forest phases of a glacial-interglacial cycle spanning ~11500 (± 1000) years of the 15-16-ka-long Holsteinian interglacial. The development of temperate mixed forests suggests a general prevalence of mild climatic conditions during the Holsteinian. The older parts of the interglacial are characterised by the strong presence of boreal tree taxa (e.g., Picea), whereas the younger parts of the interglacial are marked by the expansion of sub-Atlantic to Atlantic forest elements (e.g., Abies, Buxus, Ilex, Quercus) and the decline of boreal tree taxa. This vegetation succession suggests a general warming trend and decreasing seasonality over the course of the Holsteinian interglacial. Based on the maximum pollen abundances of indicator tree taxa (e.g., Buxus and Quercus), peak warmth was reached during the later stages of the interglacial; it was accompanied by high humidity. The forest succession of the Holsteinian interglacial was punctuated by abrupt and gradual changes in the abundances of temperate plant taxa. These vegetation changes indicate considerable intra-interglacial climate variability. In particular, two marked declines of temperate taxa leading to the transient development of boreal and sub-boreal forests were triggered by centennial-scale climate oscillations, here termed Older and Younger Holsteinian Oscillations (OHO and YHO). These oscillations occurred ~6000 and ~9000 years after the onset of the interglacial pioneer forestation in central Europe, respectively. To assess the impact of abrupt climate change on terrestrial ecosystems during the Holsteinian and to investigate the underlying driving mechanisms, the intervals spanning the OHO and the YHO at Dethlingen were subjected to decadal-scale palynological and sedimentological analyses. Based on these data, the OHO comprises a 90-year-long decline of temperate taxa associated with expansion of Pinus and non-arboreal pollen, and a subsequent 130-year-long recovery of temperate taxa marked by the pioneer expansion of Betula and Alnus. Owing to its highly characteristic imprint on vegetation dynamics, the OHO can be identified in pollen records from the central European lowlands north of 50º latitude, from the British Isles to Poland. A close inspection of individual pollen records from that region reveals the prevalence of colder winters during the OHO, with a gradient of decreasing temperature and moisture availability, and increased continentality towards eastern Europe. This climate pattern points to a weakened influence of the westerlies and/or stronger influence of the Siberian High connected to the OHO. The vegetation dynamics during the YHO are characterised by a decline of temperate taxa (particularly of Carpinus) and the expansion of pioneer trees (mainly Betula). In contrast to the OHO, frost-sensitive taxa (e.g., Ilex, Buxus and Hedera) continued to thrive. This suggests that mean winter temperatures remained relatively high (>0 ºC) during the YHO pointing to a decrease of summer warmth related to the climatic deterioration. The YHO, which has a duration on the order of 300 years, is centered within a long-term (~1500-year) decline and subsequent, millennial-scale recovery of temperate taxa. Because the impact of the OHO and the YHO on the vegetation at Dethlingen was markedly different, both short-term climate oscillations may have been caused by different trigger mechanisms. For the OHO, the inferred regional-scale winter cooling over central Europe lasting for several decades points to a decrease in ocean heat transport, most likely related to a transient slowdown in North Atlantic Deep Water formation. This view is supported by the strong resemblance of the OHO to the 8.2 ka event of the Holocene with regard to the duration, imprint on terrestrial ecosystems, spatial pattern of the climatic impact, timing within the respective interglacial, and prevailing interglacial boundary conditions. In contrast, the presence of frost-sensitive taxa during the YHO appears to exclude a reduction in oceanic heat transport as postulated for the OHO. Instead, the long-lasting, gradual changes in the abundances of temperate taxa suggest a connection to orbital forcing, with the triggering mechanism causing the centennial-scale vegetation setback itself remaining unclear. The characteristics of short-term climate variability were investigated based on microfacies and time series analyses of a ~3200-year-long, annually laminated window of the Dethlingen record. The annual laminations at Dethlingen comprise biogenic varves consisting of two discrete sub-layers. The light layers, which are controlled by the intensity of diatoms blooms during spring/summer, reflect changes in the productivity of the Dethlingen palaeolake. In contrast, the dark layers, which consist predominantly of amorphous organic matter and fragmented diatom frustules, represent sediment deposition during autumn/winter. Spectral analyses of the thicknesses of the light and dark layers have revealed several peaks exceeding the 95% and 99% confidence levels that are near-identical to those known from modern instrumental data and Holocene records. Decadal-scale signals at periods of 90, 25, and 10.5 years are likely associated with the 88-, 22- and 11-year solar cycles; hence, solar activity appears to have been a forcing agent in productivity changes of the Dethlingen palaeolake. Sub-decadal-scale signals at periods between 3 and 5 years and ~6 years may reflect an influence of the El Niño-Southern Oscillation (ENSO) and the North Atlantic Oscillation (NAO) on varve formation during winter.
The Alborz Mountains are forming a ~100 km wide, E-W trending mountain chain where individual summits are up to 5000 m in elevation. The Alborz Mountains range are part of the Alpine orogen and are straddling a 2000 km wide area S of the Caspian Sea. The rocks of the Alborz Mountains consist of Neogen sediments, which are affected by folding and faulting. In the western part of the Alborz Mountains the folds and faults are trending NW-SE, whereas in the eastern part they are trending NE-SW. GPS data confirm N-S shortening including dextral strike-slip along ESE-WNW trending faults, and sinistral strike-slip along ENE-WSW trending faults. The present thesis is focusing on the active Garmsar salt nappe, the fragmented roof of which is pierced by rock salt which extruded near the front of the Alborz Mountains Range. During the past 5 m.y. the front of the Alborz chain migrated towards SSW on top of the salt of the Garmsar basin. The salt was squeezed towards SSW and took place at the Great Kavir. The extruded salt is forming the Eyvanekey plateau between the cities of Eyvanekey and Garmsar. Both the Garmsar salt nappe and the Eyvanekey plateau are dextrally displaced for ca. 9 km along the Zirab-Garmsar fault. Structural analyses of the Garmsar salt nappe indicate three different groups of joints which are trending perpendicular and parallel to the local mechanical anisotropy. The folds of the study area are congruent (type 2 and 3 after Ramsay) resulting from viscose inhomogeneous flow. InSAR-Investigations suggest the Alborz Mountains to be lifted up by ca. 1 cm/a, while horizontal shortening is active at a rate of 8 ±2 mm/a. These values are consistent with GPS data. Based on nine „Advanced Synthetic Aperture Radar“ (ASAR) scenarios, produced by the ENVISAT satellite of the European space agency between 2003 and 2006, we used interferograms to map the displacement via 22 increments during 2 – 18 months. The results suggest that the topographic height of the surface of the salt is changing at a rate which is controlled by the season. The displacement ranges from subsidence at -40 to -50 mm/a to uplift of 20 mm/a. In order to investigate the time-dependent deformation with high spatial resolution, we used algorithms which are based on data of small base lines (SBAS). The resulting interferometric SAR time series analyses also suggest that the study area is largely subsiding at a rate that is controlled by the seasons. The map with the averaged LOS deformation velocities, on the other hand, suggests the subsidence to increase from the upper part of the salt nappe towards deeper topographic 5 levels of the agricultural lowlands. The major part of subsidence is probably caused by the annual rainfall which results in subrosion of salt. The spatial changes in the subsidence rate are probably controlled by the distribution of fountains, mining activity at the margin of the salt glacier, and faults and fractures inside the salt. Striking seasonal imprints are obvious along the agricultural areas which are surrounding the Garmsar salt nappe. These areas are rapidly subsiding in summer and spring when groundwater is used for irrigations. The maximum rate of subsidence (40-50 mm/a) is located E and W of the Eyvanekey plateau, where large areas are irrigated. The maximum displacement is 20 mm/a in the farmland and 5 mm/a in the center of the salt nappe. Depth estimates using Euler deconvolution method for gravimetric and magnetic data suggest the salt to extrude from a depth less than ca. 2000 m. The gravity field of the study area is characterized by strong anomalies in the SW and weak anomalies in the NE. A considerable negative anomaly in the N indicates that the northern part subsided, whereas the southern part was lifted up. The seismic data show three major horizons inside the Miocene sediments: the Lower Red Formation, the Qom Formation, and the Upper Red Formation. The western part of the study area seems to be free from salt domes. The layers of the upper part of the Qom Formation show thinning along the NE and NW trending faults. In some areas the seismic reflectors indicate steep faults close the saddle of the folds. NE-SW-, NW-SE and E-Wtrending faults prevail. Analogue experiments have been carried out to extend our knowledge about the evolution of the Garmsar salt dome. We used a scaled model (34 cm * 25 cm * 2.5 cm) that was shortened perpendicular to its long side. The wedge shape of the Alborz Mountains was simulated by a wedge consisting of Styrofoam. Rock salt was simulated using Polydimethylsiloxan (PDMS), a linear viscous material with a viscosity of 2.3*104 Pa s and a density of 0.96 g/cm3 at room temperature. Other sediments were modeled using dry quartz sand. The experimental results can be used to simulate the structural evolution of the study area: The Alborz deformation front was emplaced on top of the salt rocks in the Garmsar area while migrating towards SSW. A salt basin and a salt extrusion have also been produced in the model. Cross sections through the wedge shaped analogue model indicate N- and S-dipping reverse faults, which are in line with the wedge shape of the Alborz chain. Moreover, ENE-WSW trending sinistral and ESE-WNW trending dextral strike-slip faults led to N-S shortening during the Miocene. Structural marker horizons, 6 which have been turned into Z-folds on the western fold limbs and to S-folds on the eastern fold limbs, are comparable with the folds of the study area. Solving the problem of waste is one of the central tasks of environmental protection. It is becoming increasingly difficult to find suitable sites that are acceptable to the public. Salt and salt formations have relevant properties to be utilizing as a repository for each kind of waste. The favorable properties make rock salt highly suitable as a host rock, in particular for nonradioactive and radioactive wastes. The Qom and Garmsar basins are the nearest salt diapirs to the Tehran province, and there are suitable repositories for waste disposal. Based on surface and subsurface data, the Garmsar salt diapir has been investigated as a case example for its suitability as a host and repository for various types of waste. The data used are based on field studies, interferometry, and geophysical investigations. The results of this study suggest the deep bedded salt of the Garmsar Salt Basin to be an appropriate host for the deposition of industrial waste. Rock salt of surficial layers or domes, on the other hand, is not regarded as an appropriate candidate for waste disposal.
Die kumulative Dissertation beschäftigt sich mit der atmosphärischen Konzentration von Eiskeimen, einer Unterklasse des atmosphärischen Aerosols, die bei der Eisbildung in Wolken eine zentrale Bedeutung besitzt. Messungen der Eiskeimkonzentration am Taunusobservatorium (Kleiner Feldberg) (nahe Frankfurt am Main) wurden mit dem Verfahren einer Vakuum-Diffusionskammer durchgeführt. Die Arbeit umfasst die Darstellung des angewandten Messverfahrens und die Analyse und Bewertung der Messergebnisse für den Raum Zentraleuropa, anhand von u.a. Rückwärtstrajektorien und Korrelationen zu aerosolphysikalischen Parametern. Ein signifikanter Einfluss von Mineralstaub-Ferntransport aus Wüstengebieten auf die Eiskeimkonzentration in Zentral-Europa wurde ermittelt.
Forty two samples of the Late Eocene Kiliran oil shale, Central Sumatra Basin, Indonesia were collected from a 102 m long drill core. The oil shale core represents the deposition time of about 240.000 years. Palynofacies and geochemical analyses have been carried out to reconstruct the paleoenvironmental conditions and paleoecology during deposition of the oil shale. Amorphous organic matter (AOM) is very abundant (>76%). B. braunii palynomorphs are present (3-16%) as the only autochtonous structured organic matter and generally more abundant in the middle part of the profile. The stable carbon isotopic composition of bulk organic matter (13C) varies from -27.0 to -30.5‰ and is generally more depleted in the middle part of the profile. The ratio of total organic carbon to sulfur (TOC/S), used as salinity indicator, ranges from 2.5 to 15.8 and shows variations along the profile. Slightly less saline environments are observed in the middle part of the profile. Fungal remains are generally present only in this part with a distinct peak of abundance. The presence of fungal remains is regarded as an indication for a relatively warmer climate during deposition of the middle part of the profile. The warmer climate is thought to influence the establishment of a thermocline, limiting the supply of recycled nutrients to epilimnion. Consequently, the primary productivity in the Kiliran lake decreased during deposition of the middle part of the profile as indicated by the relatively depleted 13C values and the blooming of B. braunii. The chemocline was also shoaling during the deposition according to the higher abundance of total isorenieratane and its derivatives originated from green sulfur bacteria dwelling in the photic zone euxinia. The warmer climate is also thought to influence the slightly decrease of water salinity during deposition of the middle part of the profile. The occurrence of B. braunii in Kiliran lake is also recognized from organic geochemical data. The distribution of n-alkanes is characterized by the unusual high amount of C27 n-alkane relative to the other long-chain n-alkanes. The concentrations of C27 n-alkane vary from 30.1 to 393.7 μg/g TOC and are generally in parallel with the abundances of B. braunii palynomorphs along the profile. The 13C values of this compound are about -31‰ and up to 2‰ enriched relative to those of the adjacent long-chain n-alkanes. B. braunii race A can thus be regarded as the significant biological source of the C27 n-alkane. Lower amounts of lycopane are observed in many oil shale samples (0 to 54.7 μg/g TOC). The 13C value of this compound is 17.2‰. This strong enrichment of 13C suggests that the lycopane was derived from B. braunii race L. The concentrations of lycopane develop generally in opposite with those of C27 μalkane. It is likely that both B. braunii races bloomed in alternation in the lake, probably due to changes on specific water chemistry. Norneohop-13(18)-ene and neohop-13(18)-ene derived from methanotrophic bacteria are the dominant hopanoid hydrocarbons. The sum of their concentrations varies from 40.6 to 360.0 μg/g TOC. The 13C of these compounds are extremely depleted (-45.2 to -50.2‰). The occurrence of abundant bacteria including methanotrophic bacteria was responsible for the recycling of carbon below the chemocline of the lake. The effect of the recycling of carbon is observed by the presence of a concomitant depletion (about 7-9‰) in 13C of some specific biomarkers derived from organisms dwelling in the whole phototrophic zone. 4-Methylsterane and 4-methyldiasterene homologues occur in the oil shale as the predominant biomarkers. The sum of the concentrations of all homologues are about 40.3-1,009.2 μg/g TOC with generally higher values in the uppermost and lower parts of the profile. Calcium (Ca) accounts as the predominant element in the oil shale, ranging from 5.0 to 16.7%. This element shows generally parallel variation with the 4-methylsterane and 4-methyldiasterene homologues along the profile. This suggests that these compounds were derived from biological sources favoring more alkaline and more trophic environments. On the other hand, these compounds were less abundant in the middle part of the profile which is consistent with less alkaline and less trophic environments promoting B. braunii to bloom. Alternation between Dinoflagellates and B. braunii in ancient lacustrine environments due to water chemistry changes have been known from previous studies. In the present case, distinct alternation between B. braunii abundances and concentrations of 4-methylsterane and 4-methyldiasterene homologues along the studied oil shale profile suggest a hypothesis that these compounds were derived from freshwater Dinoflagellates although dinosterane is not present in the sediment extracts. Water alkalinity and trophic level changes were most likely responsible for the alternation of Dinoflagellates and B. braunii blooming.
Das Ziel dieser Studie ist es, die Möglichkeiten und Grenzen von hochauflösenden Klimaprojektionen in orographisch beeinflussten Gebieten an den Beispielen der europäischen Alpen und des Himalajas zu prüfen. Insbesondere wird die Fragestellung untersucht, ob beobachtete regionale Muster in den höher aufgelösten Daten besser wiedergegeben werden als in den antreibenden großskaligen Daten. Dazu werden regionale Klimasimulationen des COSMO-CLM Modells und Daten von zwei statistischen Regionalisierungsmethoden mit ERA40 Reanalysen sowie Daten des globalen Atmosphäre-Ozean Modells ECHAM5/MPIOM für verschiedene Parameter des Klimasystems verglichen. Ein Vergleich mit den Reanalysen anhand täglicher Niederschlagsstatistiken ergibt, dass die COSMO-CLM Niederschlagsdaten auf der 0.5° Skala vergleichbar sind mit ERA40 Niederschlägen und mit statistisch regionalisierten ERA40 Niederschlägen. Eine zusätzliche Fehlerkorrektur der COSMO-CLM Niederschläge liefert gute Ergebnisse. Dabei sind jedoch etwa 500 Regentage notwendig, um eine robuste Fehlerabschätzung zu gewährleisten. Für das südasiatische Gebiet ist eine realistische Wiedergabe des indischen Sommermonsuns (ISM) in den Modellen von hoher Relevanz. Betrachtet man nur die Mittelwerte und zeitlichen Variabilitäten von verschiedenen Indizes des ISM, so liefert das COSMO-CLM keinen Mehrwert im Vergleich zu den antreibenden Daten. Allerdings werden die räumlichen Strukturen von Niederschlag und vertikaler Windscherung, sowie die zeitliche Korrelation der modellierten Indizes gegenüber dem ECHAM5/MPIOM Modell verbessert. Die durchgeführten COSMO-CLM Projektionen für die Jahre 1960 bis 2100 zeigen negative Trends des ISM für die SRES Szenarien A2, A1B und B1. Die negativsten Trends sind dabei im Szenario A2 zu finden, gefolgt von A1B und B1. Fast keine Trends zeigen sich im commitment Szenario. Trotz großen zeitlichen Variabilitäten sind die Abnahmen in Niederschlagsmengen, ausgehender langwelliger Strahlung und Windscherung statistisch signifikant in großen Regionen des Simulationsgebietes. Für Nordwest-Indien weisen die Projektionen teilweise einen Rückgang der Monsunniederschläge von über 70% in 100 Jahren auf. Der Rückgang der Windscherung ist hauptsächlich auf Veränderungen in der oberen Troposphäre bei 200 hPa zurück zu führen. Während in den COSMO-CLM Projektionen alle Indizes des ISM synchrone Negativtrends aufweisen, sind die Trends für den Monsunregen über Indien im globalen ECHAM5/MPIOM Model positiv. Gemäß den Definitionen der verschiedenen Indizes, sind jedoch synchrone Trends wahrscheinlicher und das COSMO-CLM liefert zu den globalen ISM Projektionen ebenfalls einen Mehrwert. Insgesamt zeigen die Ergebnisse dieser Studie, dass das COSMO-CLM wertvolle regionale Zusatzinformationen zu den globalen Modellen in den beiden untersuchten Regionen liefert. Für die Einzugsgebiete der oberen Donau und des oberen Brahmaputra liefern die COSMO-CLM Projektionen einen signifikanten Anstieg der Temperatur für alle Jahreszeiten der Jahre 1960 bis 2100. Die Werte sind generell höher im Brahmaputragebiet, mit den größten Trends in der Region des tibetanischen Plateaus. Im Niederschlag zeigen die saisonalen Anteile ebenfalls klare Trends, beispielsweise eine Zunahme des Frühjahrsniederschlags im Einzugsgebiet der oberen Donau. Die größten Trends werden wiederum in der Region des tibetanischen Plateaus projiziert mit einem Anstieg von bis zu 50% in der Länge der Trockenperioden zwischen Juni und September und einem gleichzeitigen Anstieg von etwa 10% für die maximale Niederschlagsmenge an fünf aufeinander folgenden Tagen. Für die Region Assam in Indien, zeigen die Projektionen zudem eine Zunahme von 25% in der Anzahl der aufeinander folgenden trockenen Tage während der Monsunzeit
In this thesis, laboratory investigations have been conducted to investigate several processes occurring during the melt segregation (crystal settling and compaction processes), as well as during emplacement of plutons. With the help of three different sets of centrifuge experiments rates of these three magmatic processes have been evaluated. In the first series of the centrifuge experiments, the diapiric ascent of buoyant material from two source layers at different depths was studied. Through five models, the hypothesis of ascending diapirs was tested and it was demonstrated whether a rising diapir ascends straight upward or if its ascent might be deviated by another buoyant, softer – and consequently easier to travel through – layer which is located within the overburden strata. We were interested under which conditions they can be formed. For this purpose we placed perturbations on top of both the buoyant layers; either with a set-off of both the protrusions (for three of these experiments), or with both protrusion sitting directly on top of each other (for one of the experiments). In the first experiment, we omitted the perturbations, to test which pathways diapirs take which grow from natural Rayleigh-Taylor instabilities. Three others experiments differed in the viscosity contrast between the overburden and the buoyant material. Through the experimental runs, the effects of different overburden viscosities and perturbation positions on the number of the diapirs were observed. The modeling results show that two diapirs rising from the offset perturbations do not take the same pathway through the overburden layer. Rather, each diapir takes a different pathway, with the deeper diapir piercing through its overburden while rising, regardless if it was a buoyant layer or denser overburden layers. However, when the two perturbations were situated directly above each other in the different PDMS layers, this resulted in the formation of one big diapir rather than several smaller ones, and the overburden layer was less deformed than with offset perturbations. Diapiric structures as those derived from the models without perturbation and where the perturbation are offset occur within Great Kavir Basin (Iran), where numerous salt diapirs grew from several salt horizons, which show a similar spatial distribution. The resulting structure observed in the model where the two perturbations situated directly above each other, is close to what is observed in composite batholiths such as the Flasergranitoid Zone within the Bergsträßer Odenwald Crystalline Complex (Germany). The second series of models were aimed to study crystal settling within a magma. For this purpose experiments with an artificial magma of 30 vol% olivine in 70 vol% basaltic melt were conducted to elucidate the formation mechanisms and time scales of gravitational cumulates. Through the experiments, two physical processes have been observed: (i) purely mechanical compaction, and (ii) chemical compaction induced by dissolution and re-precipitation of settled crystals. The results reveals that the mechanical settling of the dense olivine suspension occurs at about 1/6 the speed of simple Stokes settling, and a sedimentation exponent n of 4.1 is found. Evidences of chemical compaction induced by dissolution and re-precipitation of settled crystals have been highlighted by a detailed analysis of the fine structure of olivine grain boundaries. This last has revealed (1) the presence of Ca, which is characteristic only for MORB-melt, at the interface of two adjacent Ol-grains even when no melt is present; (2) a not fully crystallized boundary layer between two adjacent olivine grains. The crystal size distribution curves and the grain size growth exponent n ~3.6 indicate that diffusion controlled Ostwald ripening is the dominant crystal growth mechanism in concentrated magmatic suspensions. Finally, the formation times in natural olivine adcumulates have been calculated. The last series of centrifuge experiments deals with the crystal-melt settling-floating mechanism in a system composed of natural two pyroxene gabbro. The results have revealed a vertical evolution of the major and trace elements in the melt phase. Then, a numerical modelling of the sedimentation process of the crystals has been made in order to describe the compaction evolution with time. In comparing the numerical simulation with the centrifuge modelling, the stratification of the compacted layer in the runs is reproduced in numerical models. Moreover, on the base of the numerical and centrifuge modelling, a sedimentation exponent describing a deviation of settling in concentrated suspensions from Stokes sedimentation has been evaluated. Finally, the numerical simulation is applied to the Muskox intrusion to estimate the formation time and the melt fraction evolution in using the hindered sedimentation model calculations.
In this study, I investigate the crustal and upper mantle velocity structure beneath the Rwenzori Mountains in western Uganda. This mountain range is situated within the western branch of the East African Rift and reaches altitudes of more than 5000 m. I use four different approaches that belong to the travel-time tomography method. The first approach is based on the isotropic tomographic inversion of local data, which contain information about 2053 earthquakes recorded by a network of up to 35 stations covering an area of 140×90 km2. The LOTOS-09 algorithm described here is used to realize this approach. The second approach is based on the anisotropic tomographic inversion of the same local dataset. This method employs the tomographic code ANITA, developed with my participation, which provides 3D anisotropic P and isotropic S velocity distributions based on P and S travel-times from local seismicity. For the P anisotropic model, four parameters for each parameterization cell are determined. This represents an orthorhombic anisotropy with one vertically-oriented predefined direction. Three of the parameters describe slowness variations along three horizontal orientations with azimuths of 0°, 60° and 120°, and one is a perturbation along the vertical axis. The third approach is based on tomographic inversion of the teleseismic data, which contain information about the traveltimes of P-waves coming from 284 teleseismic events recorded by the seismic network stations. The TELELOTOS code, which is my own modification of the LOTOS-09 algorithm, is used in this approach. The TELELOTOS code is designed to iteratively invert the local and/or teleseismic datasets. Finally, I present the results of the new tomographic approach, which is based on the simultaneous inversion of the joint local and teleseismic data. The simultaneous use of these datasets for the tomographic inversion has several advantages. In this case, the velocity structure in the study area can be resolved as deep as in the teleseismic approach. At the same time, in the upper part of the study volume, the resolution of the obtained models is as good as in the local tomography. The TELELOTOS algorithm is used to perform the joint tomographic inversion. Special attention is paid in this work to synthetic testing. A number of different synthetic and real data tests are performed to estimate the resolution ability and robustness of the obtained models. In particular, synthetic tests have shown that the results of the anisotropic tomographic inversion of the local data have to be considered as unsatisfactory. For all approaches used in this study, I present synthetic models that reproduce the same pattern of anomalies as that obtained by inverting the real data. These models are used to interpret the results and estimate the real amplitudes of the obtained anomalies. The obtained models exhibit a relatively strong negative P anomaly (up to -10%) beneath the Rwenzori Mountains. Low velocities are found in the northeastern part of the array at shallower depths and are most likely related to sedimentary deposits, while higher velocities are found beneath the eastern rift shoulder and are thought to be related to old cratonic crust. The presence of low velocities in the northwestern part of the array may be caused by a magmatic intrusion beneath the Buranga hot springs. Relatively low velocities were observed within the lower crust and upper mantle in the western and southern parts of the study area (beneath the rift valley and the entire length of the Rwenzori range). The higher amplitude of the low-velocity anomaly in the south can be related to the thinner lithosphere in the southern part of the Albertine rift. In the center of the study area, a small negative anomaly is observed, with the intensity increasing with depth. This anomaly is presumably related to a fluids rising up from a plume branch in the deeper part of the mantle. According to the interpretation of the local earthquake distribution, the Rwenzori Mountains are located between two rift valleys with flanks marked by normal faults. The Rwenzori block is bounded by thrust faults that are probably due to compression.
Flusssysteme im mediterranen Raum reagieren besonders sensitiv auf Veränderungen von Umweltbedingungen, z.B. durch Neotektonik, Klimaänderungen und Landnutzung. Geowissenschaftler der Goethe-Universität Frankfurt untersuchen in diesem Zusammenhang das Einzugsgebiet des Rio Palancia (Spanien), um über die Erstellung einer Sediment-Massenbilanzierung die Entwicklungsgeschichte des Systems zu erforschen. Zur Identifizierung und Quantifizierung verschiedener Sediment-Ablagerungstypen wurde das Georadarverfahren (GPR) eingesetzt. Ziel dieser Arbeit ist es, am Beispiel fluvialer Lockersedimente das Zustandekommen von Radargrammen noch besser zu verstehen und möglichst viel Information über den Untergrund aus einem Radargramm zu extrahieren. An 30 Standorten wurden GPR-Messungen durchgeführt und mit Geoelektrik und Rammkernsondierungen kombiniert. Die Einführung einer Bearbeitungs- und Auswertesystematik gewährleistet die Vergleichbarkeit von Radardaten unterschiedlicher Standorte. Als Besonderheit werden die Radargramme jeweils auf zwei verschiedene Arten bearbeitet und dargestellt, um sowohl Strukturen herauszuarbeiten als auch die – zumindest relative – Amplitudencharakteristik zu erhalten. Erst dadurch wird eine Auswertung mithilfe der erweiterten Radarstratigraphie-Methode möglich. Diese setzt sich aus der klassischen Radarstratigraphie und der neu entwickelten Reflexionsanalyse zusammen. Dabei werden systematisch Radar-Schichtflächen, Radareinheiten und Radarfazies ermittelt und anschließend die Amplitudengröße, die Polarität und die Breite der Reflexionen betrachtet. Die Radarstratigraphie liefert objektive Erkenntnisse über Form und Verlauf von Untergrundstrukturen, während mithilfe der Reflexionsanalyse Aussagen zu relativen Änderungen von Wassergehalt, Korngrößenverteilung und elektrischer Leitfähigkeit möglich sind. Mithilfe der Radarstratigraphie wurde die Radarantwort verschiedener Sediment-Ablagerungstypen im Untersuchungsgebiet verglichen. Die Radargramme zeigen unterschiedliche Zusammensetzungen von Radarfazies. Eine Unterscheidung und räumliche Abgrenzung verschiedener Ablagerungstypen mit GPR ist somit durchführbar. Die Dielektrizität des Mediums bestimmt, zusammen mit der elektrischen Leitfähigkeit, die Geschwindigkeit und Dämpfung der elektromagnetischen Welle sowie die Reflexionskoeffizienten. Um das Zustandekommen von Radargrammen im Detail nachvollziehen zu können, ist es notwendig, die Dielektrizitätskoeffizienten (DK) der untersuchten Sedimente zum Zeitpunkt der Messung zu kennen und die Abhängigkeit des DK von petrophysikalischen Parametern zu verstehen. Deshalb wurden Proben aus den Rammkernsondierungen entnommen. Im Labor wurden der Real- und Imaginärteil des DK im Radarfrequenzbereich (mit Schwerpunkt auf 200 MHz) in Abhängigkeit von Wassergehalt, Trockendichte, Korngrößenverteilung und Kalkgehalt mithilfe der Plattenkondensatormethode bestimmt. Der DK ist in erster Linie vom Wassergehalt abhängig. Es konnte eine für die Sedimente im Untersuchungsgebiet charakteristische Wassergehalts-DK-Beziehung ermittelt werden. Die resultierende Kurve ist gegenüber entsprechenden in der Fachliteratur zu findenden Beziehungen verschoben, was vermutlich auf die hohen Kalkgehalte der Proben zurückzuführen ist. Für trockene Sedimente wurde eine Korrelation des DK mit der Trockendichte festgestellt. Bei der Bestimmung der Absorptionskoeffizienten fiel auf, dass Proben mit hohem Tonanteil selbst bei geringen Wassergehalten außerordentlich hohe Dämpfungskoeffizienten aufweisen können. Die charakteristische Wassergehalts-DK-Beziehung wurde für Modellierungen von Radardaten genutzt, die dann mit Messdaten verglichen wurden. Über die Modellierung einer einzelnen Radarspur konnte die spezielle Charakteristik der entsprechenden gemessenen Spur erklärt werden, die durch den Einfluss einer dünnen Schicht zustande kommt, deren Mächtigkeit an der Grenze der theoretischen Auflösung für die verwendete Radarfrequenz liegt. Auf Basis der Erkenntnisse aus der erweiterten Radarstratigraphie an einem Radargramm auf fluvialen Lockersedimenten war es zudem möglich, ein komplettes Radargramm zu simulieren. Es gibt das gemessene Radargramm vereinfacht, aber in guter Übereinstimmung wieder. Die Georadarmethode erwies sich als sehr gut geeignet für die Untersuchung, Identifizierung und Quantifizierung fluvialer Sedimente im Palancia-Einzugsgebiet. Die im Rahmen dieser Doktorarbeit entwickelte erweiterte Radarstratigraphie-Methode stellt ein systematisches und weitgehend objektives Verfahren zur Auswertung von Radargrammen dar, das sich auch auf andere Untersuchungsgebiete übertragen lassen sollte. Durch Laboruntersuchungen wurde der Einfluss petrophysikalischer Parameter auf den DK bestimmt. Über die Modellierungen konnten die Ergebnisse großskaliger Geländemessungen mit denen kleinskaliger Labormessungen verknüpft werden. Die insgesamt gewonnenen Erkenntnisse tragen zu einem besseren Verständnis von Radargrammen bei.
The TTL is the transition layer between the tropical troposphere and stratosphere, and is the main region where tropospheric air enters the stratosphere. In this thesis different transport processes are studied by using in situ measurements of tracers. Long-lived tracers were measured with the High Altitude Gas Analyzer (HAGAR) on board the M55 Geophysica aircraft. The instrument was developed by the University of Frankfurt and measures the long-lived tracers CO2, N2O, CFC-12, CFC-11, H-1211, SF6, CH4 and H2 with two gas chromatographic channels and a CO2 sensor (LICOR). The measurements are supported by CO and O3 measurements of other instruments. Two campaigns were conducted to obtain measurements in the TTL: SCOUT-O3 (November/December 2005 in Darwin, Australia) and AMMA-SCOUT-O3 (August 2006 in Ouagadougou, Burkina Faso). After a general introduction of the thesis in chapters one and two, the third chapter describes the findings during this last campaign. Five local flights are analyzed to study the different transport processes that occur in the tropical tropopause layer above West-Africa: deep convection up to the level of main convective outflow, vertical mixing after overshooting of air in deep convection, horizontal inmixing from the extratropical lower stratosphere, and horizontal transport across the subtropical barrier. Main findings are that the TTL over West-Africa is mostly influenced by remote convection. The subtropical barrier is not a strong barrier but more a region of transition between the extratropical and the tropical stratosphere. Chapter 4 presents the results obtained during the SCOUT-O3 campaign. From the eight local flights the last four flights (051129, 051130a, 051130b, 051205) show enhanced values of ozone, CO and CO2 between 355 and 380 K potential temperature in comparison with the first four flights (051116, 051119, 051123, 051125). Horizontal inmixing from the extra-tropical stratosphere and influence of the local convective system Hector cannot explain the enhanced values of the two flights on 30 November Therefore, other possible explanations for these enhanced CO, CO2 and ozone levels are proposed. The first explanation is vertical mixing in the vicinity of the jet stream. However, the jet cannot explain the differences between the flights on 30 November and the flights on 29 November and 5 December. Another possible explanation is influence of polluted boundary layer air masses from the Indonesian region. Especially air sampled during the flights on November 30 crossed large parts of northern Indonesia between 8 and 10 days before the measurements. Convective uplift of biomass burning and other pollution plumes can transport CO and ozone precursors into the upper troposphere, where they can significantly enhance the ozone production. The last chapter deals with the vertical ascent rate in the TTL and uses measurements of both the SCOUT-O3 and AMMA-SCOUT-O3 campaign as well as data from previous aircraft campaigns (TROCCINOX and APE-THESEO). Time scales and residence times for mean vertical transport in the background TTL are estimated for different seasons and over different geographic regions using in situ observations of CO2 and long-lived tracers. The vertical transport time scales are constrained using the seasonal variation of CO2 in the tropical troposphere as a “tracer clock” for vertical ascent. Two methods are applied to calculate the residence time in the layer between 360 and 390 K potential temperature. The first method uses the slope of the CO2 index, the second method fits the CO2 index directly to the measurements assuming a constant ascent rate. The first method yields residence times for Australia,West Africa, and Brazil of the same order, 35-45 days to 380 K and 50 days to 390 K (where no value can be derived for Australia as the slope is changing approximately one month before the campaign). For APE-THESEO, the method does not yield reasonable results. The best estimates using the second method show moderate residence times between 360 and 390 K of 60±25 days SCOUT-O3 (NH autumn) and 43±8 days for AMMA/SCOUT-O3 (NH summer). These results agree well with the results calculated using the first method. For APE-THESEO and TROCCINOX the best fits yield shorter residence times of 23±7 and 40±10 days, respectively, both during winter. These results correspond well to the expectations based on the seasonal variation of the Brewer-Dobson circulation.
An eclogite barometer has profound importance in the study of upper mantle processes and potential application to diamond prospecting. Studies on the partitioning of Li between clinopyroxene (cpx) and garnet (grt) in natural samples have shown that this particular element is very sensitive to changes in pressure and could be calibrated as the barometer demanded for bimineralic eclogites. Experiments were performed from 4 to 13 GPa and 1100 to 1400°C in the CMAS (CaO, MgO, Al2O3, SiO2) system with Li added as Li3PO4 to quantify this pressure dependence into a barometer expressed in the following equation: P= (0.00255*T-lnKd)/0.2351 where P is in GPa, T is in °C and Kd is defined as the partition coefficient of Li (in ppm) between clinopyroxene and garnet. The experimental pressures are reproduced to ± 0.38 GPa (1σ) by this equation. This barometer is strictly applicable only to CMAS. Experiments at 1300°C, 8-12 GPa showed that Henry’s Law is fulfilled for Li partitioning between cpx and grt in the concentration range of approximately 0.01 – 1 wt% Li. Direct application of the equation to experiments in natural systems performed at 1300°C from 4 GPa to 13 GPa consistently overestimates pressures by approximately 2 GPa. Our previous experiments in the system CaO-MgO-Al2O3-SiO2 + Li3PO4 showed that the partitioning of Li between garnet and clinopyroxene is pressure dependent in eclogitic bulk compositions. This supports experimentally the hypothesis of Seitz et al. (2003), based on the analysis of Li in eclogitic xenoliths and inclusions in diamond, that the partitioning of this particular element between clinopyroxene and garnet is very sensitive to changes in pressure and could be calibrated as a barometer for bimineralic eclogites. In order to calibrate this pressure dependence into a barometer, experiments were performed in natural systems using starting materials sourced from a well preserved eclogitic xenolith from the Roberts Victor kimberlite pipe (South Africa) to extrapolate our findings in CMAS to natural systems. Sixteen multianvil experiments were performed from 4-13 GPa and 1100-1500°C. Our findings reinforced the general trend we observed in the CMAS system, that KdLi cpx-grt for Li decreases with increasing P, and that at P ≥ 12 GPa, garnet is able to incorporate more Li than clinopyroxene. Multiple linear regression was applied to our experimental results to create the barometer: P = (0.000963*T – ln KdLi cpx-grt + 1.581) / 0.252 Where P is pressure in GPa, T is temperature in °C and KdLi cpx-grt is defined as the partitioning coefficient of Li obtained by dividing the concentration of Li in cpx by the concentration of Li in garnet. This barometer reproduces the experimental conditions to ± 0.2 GPa. It is applicable to eclogitic xenoliths, to garnet pyroxenites and to peridotitic and eclogitic inclusions in diamond. Application of the barometer to diamond bearing xenoliths results in pressures in the diamond stability field. Clinopyroxene is easily corrupted in xenoliths and also preferentially takes in Li during short lived metasomatic processes. Care must be taken therefore to analyse primary, unaltered clinopyroxene. Our preliminary application to natural samples shows that the barometer can be applied beyond the experimental range to pressures down to 3 GPa. Seventeen eclogitic xenoliths were chosen from a sample set of greater than 200 for their fresh microscopic and macroscopic appearance and were analyzed for Li content in coexisting garnet (grt) and clinopyroxene (cpx). These samples can be subdivided into two groups on the basis of Mg in cpx (cpfu: cations per formula unit, based on 6 oxygens): Group 1 with Mg > 0.75, and Group 2 with Mg < 0.75. Group 1 xenoliths show lower Li contents in both grt and cpx compared to Group 2. The Li barom ter calibrated in Hanrahan et al. (2009b)/Chapter 3 was applied to these samples as well as available literature data to obtain pressures of provenance - Group 2 xenoliths often provide pressures that appear unrealistic for eclogitic xenoliths. In light of observed crystal chemical relations in the natural samples, a new fitting procedure was applied to the experimental data presented in Chapter 3. This new fit appears to be more realistic than the previous fit, although a strong relationship with Mg# remains present, suggesting that Li-barometry is, at present, only applicable to Mg-rich eclogites. Inclusions in diamond, with the exception of eclogitic inclusions of coexisting majorite and cpx, often yield pressures that are inconsistent with the pressures required for diamond formation. Although an interesting observation when comparing all of the data is that inclusions in diamond have significantly higher average Li concentrations compared to xenoliths, which suggests that Li is highly present in the fluids from which diamonds form in the mantle, an observation which was previously made for the deep mantle as a result of high Li in ferropericlase inclusions in diamond (Seitz et al. 2003).
Östlich des Rwenzori Gebirges im Westen Ugandas wurden magnetotellurische Messungen durchgeführt. An 23 Stationen wurden Übertragungsfunktionen und Phasen Tensor Elemente zwischen den gemessenen magnetischen- und tellurischen Feldern im Periodenbereich von 10s bis 10000s geschätzt. Die Übertragungsfunktionen deuten eine komplexe drei dimensionale Leitfähigkeitsstruktur innerhalb der Kruste an, insbesondere in der Verbindungszone zwischen dem Rwenzori Gebirge und der östlichen Riftschulter. In dieser Arbeit wird eine alternative Darstellung der Phasen Tensor Ellipsen als Balken eingeführt. Für Perioden größer 100s zeigen die maximalen Phasen der Phasen Tensor Balken aller Stationen einheitlich in SSW-NNE und die Phasen Tensor Invarianten f min und f max weisen eine Differenz von mindestens 20° auf. Dieses auffällige Verhalten und die kleinen vertikalen magnetischen Feldr im gleich Periodenbereich kann mit einer anisotropen Leitfähigkeit in einer Tiefenbereich zwischen 30-50km mit der gut leitenden Richtung senkrecht zur Riftachse erklärt werden. Die Anisotropie könnte ihren Ursprung in orientierten Olivien Kristallen im oberen Mantel haben, wobei die Orientierungsrichtung mit der Delamination der Unterkruste unter den Rwenzoris zusammen hängen kann. Eine gut leitende Zone süd-östlich der Rwenzoris wurde in 15km Tiefe gefunden, die mit einer seismischen low velocity zone übereinstimmt und partielle Schmelzen innerhalb der Kruste andeutet. An allen Stationen steigt die minimale Phase bei der Periode 200s über 45° und zeigt einen Anstieg der elektrischen Leitfähigkeit unterhalb der Lithosphäre an.
Within the present study the occurrence and fate of the organophosphorus flame retardants and plasticizers tris(2-chloroethyl) phosphate (TCEP), tris(2-chloro-1-methylethyl) phosphate (TCPP), tris(1,3-dichloro-2-propyl) phosphate (TDCP), tris(2-butoxyethyl) phosphate (TBEP), tri-iso-butyl phosphate (TiBP), and tri-n-butyl phosphate (TnBP) in precipitation, lake water, surface runoff and groundwater from urban and remote areas in Germany was investigated between June 2007 and October 2009. 255 samples of precipitation, 210 samples of lentic surface water and 72 samples of groundwater were analyzed for the six organophosphates (OPs) by solid phase extraction followed by gas chromatography-mass spectrometry. The research focused on aspects concerning (1) the atmospheric washout of OPs by precipitation, (2) the temporal variation of OP concentrations in precipitation and in lentic surface waters as well as (3) the pollution of groundwater by OPs. The results of the study emphasize the importance of precipitation as an all-season entry-pathway for OPs in the aquatic environment, particularly in densely populated urban environments with high traffic volume and abundant usage of flame-protected products. No seasonal trends were observed for all analytes in precipitation at the urban sampling site. TCPP dominated in all precipitation and storm water holding tank (SWHT) water samples with maximum levels exceeding 1 µg/L. An accumulation of OPs deposited in SWHTs was observed with concentrations often exceeding those observed in wet precipitation. Median concentrations of TCPP (880 ng/L), TDCP (13 ng/L), and TBEP (77 ng/L) at the urban SWHT were more than twice as high as those measured at the urban precipitation sampling site (403 ng/L, 5 ng/L, 21 ng/L) located close to the SWHT. OP levels in more remote lakes were often below or close to the limits of quantitation (LOQ). Nevertheless, TCPP was the substance with the highest median concentration in rural volcanic lakes (7–18 ng/L) indicating an atmospheric transport of the compound. At urban lakes the median OP concentrations were in the range of 23–61 ng/L (TCEP), 85–126 ng/L (TCPP), <LOQ–53 ng/L (TBEP), 8–10 ng/L (TiBP), and 17–32 ng/L (TnBP). In laboratory experiments, TBEP, TiBP, and TnBP were photochemically degraded in spiked lake water samples upon exposure to sunlight. In the SWHT a seasonal trend with decreasing concentrations in summer/autumn was evident for TiBP and TnBP but not for the chlorinated OPs. The decreasing concentrations can be explained by in-lake photodegradation. Results have also shown that the occurrence of OPs in groundwater is depending on the anthropogenic impact during groundwater recharge/natural replenishment. Infiltration of precipitation was found to be no important entry-pathway for OPs into aquifers at rural sites. Highest OP concentrations (>0.1 µg/L) were determined in groundwater polluted by percolating leachate from contaminated sites or groundwater recharged via bank filtration of OP-loaded recipients. Concentrations of TCEP, TCPP, TiBP and TnBP in groundwater decreased rapidly (89–97%) during bank filtration with increasing distance from the recipient due to adsorption processes and/or biotransformation. Although TCEP and TCPP are stable within the aquifer, they are not suitable as conservative organic tracers in groundwater.
Until now, the NW Indian Ocean was sparsely covered with coral proxy records, and records from the Maldives Archipelago do not exist. The first such coral proxy record from the central Maldives is presented in this study. It originates from a massive Porites lutea (Quoy and Gaimard, 1833) colony that was sampled March 2007 in the lagoon of Rasdhoo Atoll (4°N/ 73°W), which is located in the central Maldives. The record spans a period of 90 yrs and reaches back to 1917 AD with monthly to bimonthly resolution. This study investigates temporal variations of the skeletal stable oxygen (delta18O) and carbon (delta13C) isotopes, the strontium-to-calcium (Sr/Ca), and the annual extension-rates, and their relationship to historical climate variations 1917-2007. Annual extension-rates show an increase over the 20th century, and are correlated with instrumental sea surface temperatures (SST). The interannual variation of the extension-rates within 2.5-4 years is driven by the El Niño-Southern Oscillation (ENSO). The amount of skeletal extension during the summer months is triggered by variations in the strength of the SW monsoon. Interannual and decadal variability in monsoon current activity (18-19 yrs) and rainfall over India are an expression of the summer monsoon strength. This is the reason why a statistical link between coral extension-rates and precipitation over India can be established. This implies that annual extension-rates in corals can be used as a new proxy for Indian monsoon variability on decadal resolution. The delta18O record exhibits the 20th century warming trend that is influenced by the effect of monsoon-induced cooling. delta18O also reveals interannual ENSO triggered variability, which is due to ENSO-forced variations in SST and sea surface salinity (SSS). A decadal variation at 12-14 yrs cannot be linked to SST variations in the NW Indian Ocean, but with decadal variations of SSS. They could be caused by ENSO- forced variations of the monsoon currents during the mature phase of ENSO teleconnections in the Indian Ocean in boreal winter. The Sr/Ca record does not indicate a significant warming, in spite of the observed SST rise at the sampling site. Changes in seawater Sr/Ca cannot be excluded. Nevertheless, interannual ENSO forcing is still evident. Evidence for the Pacific Decadal Oscillation (PDO) is found during 1917-1955. Afterwards, the Sr/Ca data indicate the disappearance of PDO forcing. By the combination of Sr/Ca and delta18O it is possible to detect ~80% of historical El Niño and La Niña events at the sample site. This study confirms the notion that interannual to multi-decadal climate fluctuations in the Pacific play a crucial role for climate variability in the Indian Ocean.
The present PhD-thesis was prepared within subproject B8 of the DFG-Sonderforschungsbereich (SFB) 641 “The Tropospheric Ice Phase”. The subproject B8 was entitled “Interactions of volatile organic compounds with airborne ice crystals”. Results of previous studies have shown that various volatile organic compounds (VOC) and semivolatile organic compounds (SVOC) are incorporated into the atmospheric ice phase and several uptake mechanisms are discussed in the literature. The aim of this study was to identify the dominating VOC and SVOC in airborne snow collected at Jungfraujoch in the Swiss Alps (3580 m asl) and to study in laboratory experiments the uptake mechanism of organic compounds into snow and ice. For this purpose an analytical method to analyse freshly fallen snow samples was developed and evaluated in a first step. The method consists of headspace (HS) solid phase dynamic extraction (SPDE) followed by gas chromatography combined with mass spectrometry (GC/MS). During the extraction process a new cooling device was successfully integrated into the HS-SPDE-GC/MS method to enhance the extraction yield. Extraction and desorption parameters such as the number of extraction cycles, extraction temperature, desorption volume and desorption flow rate have been optimized. Detection limits for benzene, toluene, ethylbenzene, m-, p-, o- xylene (BTEX) ranged from 19 ng L-1 (benzene) to 30 ng L-1 (m/p-xylene), while those for C6-C10 n-aldehydes ranged from 21 ng L-1 (n-heptanal) to 63 ng L-1 (n-hexanal). Furthermore, freshly fallen snow samples were collected at the High Altitude Research Station Jungfraujoch (3580 m asl, Switzerland) during the field campaigns “Cloud and aerosol characterization experiment” (CLACE) 4 and 5 in February and March 2005 and 2006, respectively. Freshly fallen snow samples collected directly in-cloud on a high altitude remote location were used as approximation of airborne ice crystals since sampling of airborne ice crystals in quantities sufficient for analysis of individual organic compounds is not yet possible. In the collected snow samples a wide range of organic compounds were identified, namely BTEX, n-aldehydes (C6-C10), terpenes, chlorinated hydrocarbons and alkylated monoaromatics. The most abundant organic compounds in snow samples from Jungfaujoch during CLACE 4 and 5 were n-hexanal with a median concentration of 1.324 μg L-1 (CLACE 5) followed by n-nonanal (CLACE 5) with a median concentration of 1.239 μg L-1. High concentration variations of the analytes in snow samples collected at the same time at the same place argue for a heterogeneous composition of snow and ice. Several indicators were found that the origin of the n-aldehydes in the snow can be attributed to direct biogenic emissions from vegetation and indirect biogenic emissions through photochemical oxidation of fatty acids and alkenes. In a second step laboratory experiments were carried out to clarify the uptake mechanism of volatile and semivolatile organic compounds into snow/ice. Organic compounds can be incorporated into the atmospheric ice phase either by the process of gas scavenging, liquid scavenging (riming) or particle scavenging. Gas scavenging (incorporation of the organic compounds from the gas phase during growing of ice crystals) revealed to be ineffective based on previous laboratory experiments in which ice crystals were growing in the presence of aromatic hydrocarbons (BTEX) in the gas phase. In the present study the process of liquid scavenging (riming) was investigated in the laboratory using aqueous standard solutions containing BTEX, naldehydes (C6-C10), methyl tert-butyl ether (MTBE) and ethyl tert-butyl ether (ETBE). The headspace above the standard solution was sampled after adjusting the aqueous solutions to definite temperatures by use of a thermostat. Measurement were carried out at 25°C, 15°C and 5°C (water), -5°C and -15°C (supercooled water) and -25°C (ice). Results have shown that the known trend of lower gas phase concentrations over water concomitant with lower temperatures (Henry’s Law) is only valid for temperatures above 0°C. At temperature below 0°C, increasing concentrations of the analytes (BTEX, MTBE, ETBE and n-aldehydes) were determined in the gas phase together with decreasing temperatures. Dimensionless Henry’s law coefficients (KAW) were calculated from the concentrations of the organic compounds in the headspace above the standard solutions at temperatures between 25°C and -25°C. The observed inversion of Henry’s law coefficients of volatile and semivolatile organic compounds at a water temperature of approximately 0°C is explained by the formation of ordered zones of H2O molecules in supercooled water called “ice-like-clusters”. Together with decreasing temperatures the degree of formation of ordered zones increases which results in the removal of the organic molecules from the liquid phase and transfer into the gas phase. At a temperature of -25°C the supercooled water is converted into ice and a further significant increase of the gas phase concentrations of hydrophobic compounds such as BTEX is observed. In comparison, less hydrophobic compounds such as MTBE, ETBE and n-aldehydes are detected in lower amounts in the gas phase above the water/ice phase due to the higher water solubility and lower Henry coefficients compared to BTEX. The results show that in the absence of particles the uptake of BTEX MTBE, ETBE and C6-C10-naldehydes into ice not enhanced during freezing of a supercooled liquid, since at -25°C for these analytes the concentrations in the gas phase are higher at -25°C (ice) compared with -15°C (supercooled liquid). The heterogeneous distribution of BTEX and n-aldehydes concentrations in snow samples collected during the CLACE field campaigns suggests that adsorption of the organic compounds to particles followed by incorporation of the particles into the snow and ice might play a major role in the uptake process of organic compounds into snow and ice. To increase the knowledge about uptake processes of organic compounds into snow and ice further experiments are required with should include aerosol particles in the experimental setup to evaluate the influence of particle scavenging in the uptake processes.
Delthyridoid spiriferids are characterized by a global abundance and fast evolution during Silurian and Devonian, and, therefore, are used as important biostratigraphical and palaeobiogeographical tools. In this work, delthyridoid brachiopod faunas from different regions of today’s world, resp., of different palaeobiogeographical units, are compared side-by-side to investigate their phylogenetic relationships and to improve, in a second step, the palaeobiogeography from Late Silurian to Early Eifelian time. A new systematics of Delthyridoidae is established which is more complicated than hitherto assumed. The results of this study are mainly based on direct comparison of articulated and isolated brachiopod shells, external and internal moulds, as well as latex casts and serial sections. The computer supported cladistic analyses have turned out not to be useful due to different kinds of preservation resulting in an incomplete matrix which is insufficient for reliable cladograms. A further problem in terms of cladistical analyses are various convergences during the evolution of spiriferids. Many characters evolved independently from each other at different times in each lineage so that autapomorphies are hardly or not at all recognizable. As a result, families and genera are only definable by a combination of characters rather than by a single or a few autapomorphies. As a new method, 3D reconstruction from serial sections is introduced which made it possible for the first time to compare directly mouldic and shelly material. Preliminary results are presented herein. Statistical analyses of measurements taken from new taxa are made but regarded as a descriptive argument rather than a deciding factor for taxonmy due to incomplete preservation and/or tectonic deformation. Brachiopods, especially type material, from collections of different institutions and museums are studied as well as personal material, whenever possible collected from topotype outcrops. Emended diagnoses, if necessary, from family to species level are given. During this work several new taxa have been erected: 7 new families: Australospiriferidae, Murchisonispiriferidae, Orientospiriferidae, Otospiriferidae, Patriaspiriferidae, Rostrospiriferidae, and Trigonospiriferidae; 6 new genera, 1 of these in open nomenclature: Cyclopterospirifer, Hallispirifer, Parlinispirifer, Murchisonispirifer, Shujiapingensispirifer, and gen. nov. B; and 3 new species: Patriaspirifer merriami, Patriaspirifer johnsoni, and Murchisonispirifer feldmani; 1 taxon is defined as nomen novum: Orientospirifer nakaolingensis wani. In the framework of this project, 2 families: Filispiriferidae and Multispiriferidae; 1 subfamily: Multiplicatispiriferinae, 6 genera, 1 of them in open nomenclature: Frequentispirifer, Leonispirifer, Multiplicatispirifer, Ovetensispirifer, Turcispirifer, and Gen. A; and 9 new species, 3 of them in open nomenclature: Filispirifer hamadae, Leonispirifer leonensis, Multiplicatispirifer foumzguidensis, Oventensispirifer novascotianus, Quiringites arensentiae, Turcispirifer turciae, Multiplicatispirifer cf. foumzguidensis, Quiringites cf. arensentiae, and ?Turcispirifer sp. A which have already been established are also described in this work. The brachiopod faunas studied consist of externally very similar spiriferids which have been identified as same genera, species, or even subspecies in earlier times. These forms are considered as 6 distinct morphotypes Howellella-, Arduspirifer-, Acrospirifer-, Euryspirifer-, Paraspirifer-, and Multiplicatispirifer-like morphotypes, which are briefly introduced. The new systematics is characterized by different clades, the European/North African delthyridoid spiriferid clade, the North American delthyridoid spiriferid clade, the Asian delthyridoid spiriferid clade, the Malvinokaffric delthyridoid spiriferid clade, and the delthyridoid multiplicated spiriferid clade. Each of them is described in a cladistic and in a phylogenetic way. Their phylogenetic relationship sheds new light on palaeobiogeographical interpretations for the different stages from Late Silurian to early Middle Devonian time. A tendency for increasing endemicity is seen until the end of the Early Emsian, which is interrupted by short term regional faunal exchange within a province or within a realm, followed by a loss of endemicity resulting in global distribution of brachiopod genera until the end of Givetian time. The Old World Realm is re-defined due to the lack of phylogenetic relationship between its faunas and subdivided into the European Realm, consisting of the Gondwanan and Avalonian provinces, and the Asian Realm, consisting of the Siberian, Sino, and Mongolian provinces. A reconstruction of Lower Devonian palaeobiographical map is introduced.
NASAs Stardust Mission ist die erste Mission, die - nach den Apollo Missionen zum Mond - Material von einem extraterrestrischen Körper erfolgreich für die Untersuchung auf der Erde, zurückgebracht hat. Desweiteren konnten erfolgreich Proben von einem Interstellaren Partikelstrom aufgesammelt werden, der das Sonnensystem derzeit passiert. Die Mission erlaubt einen Einblick in die Beschaffenheit der Kometenpartikel, die Rolle von Kometen im Sonnensystem sowie den Eintrag von Staub in die Zodiakalwolke. Desweiteren erlaubt die Analyse der Kometenpartikel den direkten Vergleich zu bereits untersuchten Meteoriten und Interplanetaren Staub Partikeln (IDPs) die auf der Erde bzw. deren Stratosphäre gesammelt wurden. Stardust ist die vierte ”Discovery” Mission und wurde am 7. Februar 1999 gestartet. Während des Fluges zum Kometen 81P/Wild 2 wurde ein interstellarer Partikelstrom beprobt und der Asteroid Annefrank passiert. Nach fünf Jahren kam es zum Zusammentreffen mit dem Kometen 81P/Wild 2 und über fünf Minuten, wurden Proben mit einer Auffangvorrichtung eingesammelt. Es dauerte weitere zwei Jahre bis die Stardust Sonde die Proben erfolgreich zur Erde zurückgebracht hat und zur Untersuchung freigegeben wurden. Interstellare und kometare Partikel wurden mit einer tennisschlägerartigen Auffangvorrichtung eingefangen, die aus einer Vielzahl von Aerogel Zellen aufgebaut ist. Das für die Stardust Mission verwendete Aerogel besteht aus SiO2 dessen dendritische Struktur zu 99,8 % aus Luft (Poren) besteht. Dadurch erscheint es nahezu transparent, was die optische Suche mit Mikroskopen nach den Einschlagsspuren der Körner vereinfacht. Die jeweiligen Partikel wurden auf unterschiedlichen Seiten der Vorrichtung eingefangen, da unterschiedliche Eigenschaften des Aerogels notwendig waren und um sie später voneinander unterscheiden zu können. Die Seite, in der die Kometenpartikel eingefangen wurde, musste Körner mit unterschiedlichen Grössen, Morphologien und niedrigeren Geschwindigkeiten abbremsen, während auf der interstellaren Seite die Körner von wesentlich höheren Geschwindigkeiten abgebremst werden mussten. Die Aerogelzellen haben ein variierendes Dichteprofil: an der Oberfläche ist die Dichte geringer (5 mg/ml) und erhöht sich mit der Tiefe auf 30-50 mg/ml. Dieses Dichteprofil ist notwendig, da beim Einschlag der Körner auf das Auffangmedium ein hoher Druck entsteht, der umso geringer ist, je niedriger die Dichte im Moment des Auftreffens ist. Die Aerogelzellen für die Kometenpartikel haben drei Lagen mit unterschiedlichen Dichten, die Zellen für die interstellaren Körner haben zwei unterschiedliche Dichten (Tsou et al., 2003)....
New industries are recognized as new impetus to national wealth. At the same time, they are increasingly becoming geographically concentrated in some well defined areas. But current studies on the emergence of industrial clusters tend to analyze favorable driving factors. This dissertation takes the example of a Chinese endogenous industrial cluster, the traditional Chinese medicine (TCM) cluster at Tonghua, a small peripheral city in Northeastern China, to contribute to the theoretical understanding of the emergence of industrial cluster as a co-evolutionary process of organizations, institutions and firms, or, to put it more broadly, as economic evolution embedded in complex socio-economic contexts. The recent advance in evolutionary and co-evolutionary economics which considers the economy and economic landscape as dynamic process instead of equilibrium can be regarded as a part of broader and more intellectual turn of quest for history in social sciences. Although the principle of "history matters" is widely acknowledged, it tends to be reduced to a quite simple concept of "path dependence". However, path dependence cannot offer space for new path creation, except from an external shock. Accordingly, the role of human conscious action or Schumpeterian innovation should be added to path analysis through the concept of path creation. Furthermore, and more importantly, history should be understood as context, and historical context can be explored through the understanding of multi-paths and interaction among them over time. So path inter-dependence (co-evolution between paths) would be useful to better understand the complexity of real history. Since the industrial cluster is composed of interconnected firms and is also subject to changes in institution and technology, I will focus on the multi-way causal relationship between firm, institution and technology. The theorizing is not entirely new, but most of the theoretical and empirical discussions are at the national or industrial level, not regional or local one. A competitive cluster can be regarded as a co-evolutionary hotspot in which multiple populations actively interact and are interconnected. Co-evolution itself is a dynamic and evolutionary process. So I will adopt a dynamic and evolutionary view to examine co-evolutionary degree or co-evolutionary effects in the Tonghua pharmaceutical cluster through time. After a brief introduction which deals with the national institutional changes that are highly associated with new venture creation, entrepreneurship, and innovation, with registrations on drug and healthcare system, and with changes in market demand of China’s pharmaceutical industry and geographical distribution, I will collect evidences from three aspects based upon field survey and second hand data, i.e., the history of the enterprises, the origin of entrepreneurship, and the knowledge of evolution, linking their respective generative relationships through the genealogical method. In this volume, the evolution of the Tonghua pharmaceutical firm organization, the formation of local entrepreneurship, historical accumulation of knowledge, and particular knowledge of transfer among generations of firms will be discussed, then I will probe into co-adaption and co-evolution between local formal and informal institutions and organizations in Tonghua’s TCM industry. In addition, I will try to understand the co-evolutionary process at different geographical levels (namely, national and local). In summary, my main findings include the following several points. Firstly, in the course of the emergence of Tonghua’s pharmaceutical industry, local social networks and the traditional alliance between enterprises and government have played important roles. Secondly, the most important factor that influences the evolution of endogenous industrial clusters such as the Tonghua pharmaceutical industry in transitional countries is not the change in technology, but the change in fundamental national institutions. Thirdly, the success of the Tonghua pharmaceutical industry can be ascribed to the creation of multiple paths largely based on initial conditions, which implies that economic policy should have historical consciousness, namely, new economic innovation should make full use of both historical legacies and existing assets. Finally, it is co-adaption and co-selection of firm organization, institution, and technology that have jointly made Tonghua’s pharmaceutical industry become highly competitive, which means that whether one region can grasp new opportunities partially depends on its capabilities to coordinate a varity of development agents.
Trace elemental concentrations of bivalve shells content a wealthy of environmental and climatic information of the past, and therefore the studies of trace elemental distributions in bivalve shells gained increasing interest lately. However, after more than half century of research, most of the trace elemental variations are still not well understood and trace elemental proxies are far from being routinely applicable. This dissertation focuses on a better understanding of the trace elemental chemistry of Arctica islandica shells from Iceland, and paving the way for the application of the trace elemental proxies to reconstruct the environmental and climatic changes. Traits of trace elemental concentrations on A. islandica shells were explored and evaluated. Then based the geochemical traits of the shells, four non-environmental/climatic controlling is indentified. (1) Trace elemental concentrations of bivalve shells are effected by early diagenesis by the leach or exchange of elemental ions, especially in shell tip part, even with the protection of periostrucum; (2) The analytical methods also affect the results of trace elemental concentrations, especially for the element, such as Mg, which is highly enriched in organic matrices; (3) Shell organic matrices are found play a dominating role on the concentration of trace elements on A. islandica shells. Most trace elements only occurred in insoluble organic matrices (IOM), although others are only found in the carbonate fraction. IOM of A. islandica shells is significantly enriched in Mg, while Li and Na are more deplete in IOM, but enriched in shell carbonate. Ba is more or less even contented in IOM and shell carbonate. The concentrations of certain elements vary between primary layer and secondary layer; (4) The vital /physiological controlling on trace elemental distributions of bivalve shells is also confirmed. Six elemental (B, Na, Mg, Mn, Sr, and Ba) concentrations show significant correlation (exponential functions) with ontogenetic age and shell grow rates (logarithmic equations). It is worthy to remark that B, Mg, Sr and Ba concentrations are negatively correlated with shell growth rate, positive with ontogenetic age, while the concentrations of Na and Mn show the opposite trends. At last, all the controlling described above can be taken into account and corrected to extract the environmental and climatic signal by a kind of standardization. The derived six exponential functions of the high correlations between six trace elemental concentrations and ontogenetic year are applied to make the standardization of these element-Ca ratios. The gotten standardized indices are compared with the variations of environmental and climatic parameters in this region, and many correlations are found. Standardized indices of Sr/Ca ratios are strongly related to the sun spot number, autumn NAO, autumn Europe surface air temperature (SAT) and Arctic sea surface temperature anomaly (TA), and those of Mg/Ca ratios are strongly associated with Arctic TA, Europe SAT and Solar variation (irradiance). The variations of autumn Europe SAT demonstrated more similarity with standardized indices of B/Ca than other parameters. Except for the SAT index of Arctic, the standardized indices of Na/Ca showed no distinct relation to temperature. European precipitation and the Arctic sea level pressure index compared well the Na/Ca ratios of the shells, and so did the autumn NAO. Standardized indices of Mn/Ca were correlated with the number of hurricanes in the North Atlantic, Northern Europe SAT and sun spot number.
The crude oil constituents benzene, toluene, ethylbenzene, and the three xylene isomers (BTEX) are the dominating groundwater contaminants originating from surface spill accidents by oil production facilities and with gasoline and jet fuel. Thereby BTEX posing a threat to the world´s scarce drinking water resources due to their water solubility and toxicity. An active remediation cleanup involving a BTEX event proves not only to be very expensive but almost impossible when it comes to the complete removal of contaminants from the subsurface. A favoured and common practice is combining an active remediation process focussing on the source of contamination coupled together with the monitoring of the residual contamination in the subsurface (monitored natural attenuation; MNA). MNA include all naturally occuring biological, chemical and physical processes in the subsurface. The general goal of this work was to improve the knowledge of biodegradation of aromatic hydrocarbons under anaerobic conditions in groundwater. For this groundwater and soil at the former military underground storage tank (UST) site Schäferhof – Süd near Nienburg/Weser (Niedersachsen, Germany) were sampled and analysed. The investigations were done in collaboration of the Umweltbundesamt, the universitys of Frankfurt and Bremen and the alphacon GmbH Ganderkesee. To investigate the extent of groundwater contamination, the terminal electron acceptor processes (TEAPs) and the metabolites of BTEX degradation in groundwater, six observation wells were sampled at regular intervals between January 2002 and September 2004. The wells were positioned in order to cover the upstream, the source area and the downstream of the presumed contamination source. Additionally, vertical sediment profiles were sampled and investigated with respect to spreading and concentration of BTEX in the subsurface. A large residual contamination involving BTEX is present in soil and groundwater at the studied locality. Maximum BTEX concentration values of 17 mg/kg were recorded in analysing sediment in the unsaturated zone. In the capillary fringe, values of 450 mg/kg were recorded (October 2004) and in the saturated zone maximum values of 6.7 mg/kg BTEX were detected. The groundwater samples indicate increasing BTEX concentrations in the groundwater flow direction (from 532 µg/l up to 3300 µg/l (mean values)). Biodegradation of aromatic hydrocarbons under anaerobic conditions in the sub surface at contaminated sites is characterised by generation of metabolites. From the monoaromatic hydrocarbons BTEX metabolites such as benzoic acid (BA) and the methylated homologs and C1-and C2-benzyl-succinic acids (BSA) are generated as intermediates. A solid-phase extraction method based on octadecyl-bonded silica sorbent has been developed to concentrate such metabolite compounds from water samples followed by derivatization and gas chromatography/mass spectrometry (GC/MS) of the extracts. The recovery rate range between 75 and 97%. The method detection limit was 0.8 µg/l. Organic acids were identified as metabolic by-products of biodegradation. Benzoic acid, C1-, C2- and C3-benzoic acid were determined in all contaminated wells with considerable concentrations. Furthermore, the depletion of the dominant terminal electron acceptors (TEAs) oxygen, nitrate, and sulphate and the production of dissolved ferrous iron and methane in groundwater indicate biological mediated processes in the plume evidently proving the occurrence of NA. A large overlap of different redox zones at the studied part of the plume has been observed. A important finding in this study is the strong influence of groundwater level fluctuations on the BTEX concentration in groundwater. A very dry summer in 2003 was recorded during the monitoring period, resulting on site in a drop of the groundwater level to 1.7 m and a concomitant increase of BTEX concentrations from 240 µg/l to 1300 µg/l. The groundwater level fluctuations, natural degradation and retention processes essentially influence BTEX concentrations in the groundwater. Groundwater level fluctuations have by far a stronger influence than the influence of biological degradation. Increasing BTEX concentrations are hence not a consequence of limited biological degradation. Another part of the study was to observe the isotopic fractionation of the electron acceptor Fe(III), due to biologically mediated reduction of Fe(III) to the watersoluble Fe(II) at the site and first field data are presented. Both groundwater and sediment samples were analysed with respect to their Fe isotopic compositions using high mass resolution Multi Collector-Inductively Coupled Plasma-Mass Spectrometry (MC-ICP-MS). The delta56Fe -values of groundwater samples taken from observation wells located downstream of the source area were isotopically lighter than delta56Fe -values obtained from groundwater in the uncontaminated well. The Fe isotopic composition of most parts of the sediment profile was similar to the Fe isotopic composition of uncontaminated groundwater. Thus, a significant iron isotope fractionation can be observed between sediment and groundwater downstream of the BTEX contamination.
Die vorliegende Arbeit beschäftigt sich mit der geochemischen und isotopischen Analyse detritischer Zirkonminerale aus rezenten Sedimenten des weit verzweigten Orange- und Vaal River Flusssystems in Südafrika. Zirkone kristallisieren überwiegend aus krustalen Schmelzen und sind äußerst resistent gegenüber jeglicher Zerstörung und damit ein idealer Kandidat zur Rekonstruktion früherer Krustenbildungsprozesse der geologischen Erdgeschichte. Der kombinierte Ansatz der U-Pb Altersdatierung, der Hf Isotopie und der Spurenelementgeochemie mittels Laserablation und des Einsatzes induktiv-gekoppelter Sektorfeld- und Multikollektormassenspektrometer ermöglicht es die krustale Wachstums- und Entwicklungsgeschichte des südafrikanischen Kratons zu erfassen. Die mehr als 1200 U-Pb Analysen der Zirkone weisen 4 tektonische Hauptphasen des südafrikanischen Kontinents nach: 1. die Panafrikanische Orogenese (0.5-0.7 Ga), 2. das Namaqua-Natal Faltengürtelorogen (1.0-1.3 Ga), 3. die Kheis Orogenese (1.8-2.0 Ga) und 4. die westliche Kaapvaal-Kratonisierung (2.9-3.2 Ga). Allerdings zeigt sich, dass die 13 Probenlokationen überwiegend lokale bzw. regionale U-Pb Altersdaten ihrer umgebenden Herkunftsgebiete liefern. Die Hf Isotopie der Zirkone der verschiedenen tektonischen Hauptphasen Südafrikas stellen ihre differenzierte Akkretions- und Aufschmelzungsgeschichte dar. Die panafrikanischen Zirkone zeigen eine ausgeprägte Durchmischung von juvenilem und recyceltem Material. Die mesoproterozoischen (Namaquan) Zirkone entstanden aus juvenilem Magma während eines Inselbogen-Kontinent-Kollisionsereignisses. Die paläoproterozoischen und archaischen Zirkone sind Produkte von aufgeschmolzener prä-existierender kontinentaler Kruste oder vom Mantel abstammende Schmelzen, die durch kontinentale Kruste kontaminiert wurden. Die berechneten Hf Modellalter, so genannte „Mantelextraktionsalter" ergeben zwei Maxima, die zwei Stadien juvenilem Krustenwachstums einschließen, einmal vor 1.4 und 3.2 Ga. Dieses krustale Wachstum zeigt eine Übereinstimmung mit den progressiv episodischen Modellen von Nagler & Kramers (1998) sowie Condie (2000) mit Höhepunkten zwischen 3.0 und 2.0 Ga sowie den Studien von Wang et al. (2008) mit krustalen Wachstumsperioden von 1.6 bis 2.2 und 2.9 bis 3.4 Ga auf dem Nordamerikanischen Kontinent und auf dem Gondwana-Kontinent (Australien) von Hawkesworth & Kemp 2006) und implizieren wohl ein globales kontinentales Krustenwachstum. Die Abgrenzung und Wiedererkennung der Zirkone anhand der chemischen Zusammensetzung zu möglichen Muttergesteinen zeigen noch keine viel versprechenden Ergebnisse. Generell weisen die Zirkone eine magmatische granitoide Zusammensetzung kontinentalen Ursprungs auf. Eine Auffälligkeit stellen die erhöhten Spuren- und leichten Seltenenerdelemente in Zirkonen jeglicher Altersklassen dar. Nachfolgende Arbeiten müssen zeigen, wie und ob diese Anreicherungen Einfluss auf die chemische Zusammensetzung, die U-Pb Datierung und vor allem die Hf-Isotopie der Zirkone haben.
Der neoproterozoische Faltengürtel Kameruns (NFBC) ist durch Zahlreiche Pan- Afrikanische Plutone charakterisiert, die von krustalen Scherzonen durchsetzt werden. Der NFBC resultiert aus der Konvergenz des Westafrikanischen und des Kongo/Saõ-Francisco Kratons. Die Borborema Provinz (BOP) in NE-Brasilien wird als Äquivalent des NFBC angesehen. Bisher vorliegende Daten legen nahe dass die Borborema Scherzonen in kontinentaler Kruste durch dextrale Extrusion der BOP enstanden sind. Letztere wurde durch differentielle Bewegungen (Rotation induziert durch Subduktion und Kollision) des Kongo/Saõ- Francisco und des Westafrika-Kratons ausgelöst. Die Aktivität der Scherzonen fällt mit einer Hochtemperatur-Mittel- bis Niederdruckmetamorphose zusammen, welche mit partieller Aufschmelzung und Intrusion krustaler sowie Mantelschmelzen einhergeht. Die Bewegungen entlang dieser Scherzonen begannen zwischen 590 und 570 Ma und hielten bei abnehmender Temperatur bis etwa 500 Ma an. Ob die Scherzonen der BOP tatsächlich in den NFBC hineinreichen, war bisher nicht eindeutig geklärt. Die tektonometamorphe und magmatische Entwicklung des NFBC ist aufgrund fehlender struktureller, petrologischer und geochronologischer Daten kaum verstanden. Die vorliegende Arbeit befasst sich mit der Platznahme und Deformation der Plutone im Bereich des westlichen NFBC in der Region von Bafoussam-Batcha. Es wurden strukturelle Untersuchungen sowie U-(Th)-Pb Datierungen von Zirkon und Monazit durchgeführt. Die gewonnenen Daten werden mit bisher vorliegenden Daten aus den benachbarten Arealen des NFBC und aus äquivalenten Arealen Brasiliens verglichen. Innerhalb des NFBC lassen sich drei wesentliche proterozoische Gesteinseinheiten unterscheiden: (1) hoch-gradige metamorphe Komplexe mit palaeoproterozoischem Alter (Eburnium), bestehend aus Metasedimenten und Metaplutoniten, welche im Pan-Afrikanischen Granit-Batholith von Zentral-Kamerun vorkommen (in der Region von Bafia und Adamaoua); (2) einen Schiefer-Gürtel neoproterozoischen Alters, der die Becken von Poli, Lom und Yaoundé beinhaltet, und (3) Pan-Afrikanische (Meta-)Granitoide. Untersuchungen im nördlichen (Region von Poli), südlichen (Region von Yaoundé) und östlichen (Region von Lom-Ngaoundere) zeigen, dass die geodynamische Entwicklung durch Überschiebungs und Blatterverschiebungstektonik charakterisiert ist. Im nördlichen NFBC existieren E-W streichende, flach einfallende Foliationen, welche während der Überschiebung des NFBC auf den Kongo-Kraton entstanden. Im westlichen NFBC existieren vor allem geochemische und petrologische Daten. Die regionale Geologie wird hier durch Pan-Afrikanisches grundgebirge bestimmt, welches aus Graniten und Metamorphiten besteht, die wiederum von känozoischen Magmatiten (Granite, Vulkanite) durchsetzt bzw. überlagert werden. Vorhandene Daten zu Pan-Afrikanischen Plutonen des Untersuchungsgebiets und angrenzenden Regionen zeigen, dass in vielen Regionen ein große Variabilität hinsichtlich des Gesteinschemismus vorliegt, welche von basischen bis hin zu granitischen Gesteinen reicht, wobei der geochemische Charakter i.d.R. kalkalkalin bis alkalin ist. Das initiale Strontium-Verhältnis und Sm-Nd Daten einiger Granite indizieren eine Aufschmelzung im Mantel bei anschließender Kontamination durch kontinentale Kruste. Aufgrund der Anfälligkeit der Rb-Sr Methode existieren kaum verlässliche Alter von Granitoiden des NFBC. Durch die großen Fehler der Rb-Sr Alter sind neben den Platznahmealtern auch die Zeitpunkte der vorhandenen Wiederaufschmelzung weit gehend unbekannt. Durch detaillierte Geländearbeit gelang eine Gliederung des Areals in verschiedene Teilkomplexe. Diese sind der Migmatit-Komplex von Foumbot (MCF), der Bangwa-Komplex (BC), der Komplex von Chepang (CC) und der jüngeren Batié-Pluton (BP), welcher die übrigen Komplexe diskordant durchschlägt. Der BP selbst wird vom känozoischen Batcha Pluton durchsetzt. Innerhalb des MCF existiert eine bedeutende ENE-WSW streichende Scherzone. Im zentralen und südlichen Arbeitsgebiet reichen NE-SW streichende Scherzonen in den BP sowie in den CC und den BC hinein. Der MCF besteht aus Diatexit, Metatexit und Amphibolit. Merkmale wie Scherfaltung älterer Gefüge entlang ENE-WSW streichender Scherflächen und progressive Leukosombildung im Bereich der Faltenscharniere machen deutlich, dass partielle Aufschmelzung mit zunehmender Deformation einhergeht. Bereiche mit hoher Strain-magnitude zeigen koaxiale Plättung an. Die ENE-WSW verlaufende Scherzone weist dextrale Kinematik auf, wobei ältere sinistrale Bewegungen nicht ausgeschlossen werden können. Einzelzirkone von Diatexiten der MCF wurden mittels LA-ICPMS datiert. Mindestens drei Altersdomänen wurden dabei identifiziert: (a) elongierte bis gerundete Zirkon-Kerne mit Altern um 671 ±6 Ma; (b) oszillierend zonierte Zirkon-Mäntel, wahrscheinlich magmatischen Ursprungs, mit einem Alter von 639 ±5 Ma, interpretiert als das Intrusionsalter des Diatexits; (c) rekristallisierte Zirkon-Ränder mit einem Alter von 597 ±6 Ma, welches vermutlich die Metamorphose und Anatexis datiert. Der BC setzt sich aus unterschiedlich stark deformiertem Quarz-Diorit, Granodiorit, Syenogranit, Leucogranit und Monzonit zusammen. Quarz-Diorit und Granodiorit erscheinen in Form von cm- bis m-mächtigen foliierten Körpern. Die Foliation ist im Osten subhorizontal, gen Westen aber fällt sie zunehmend steil nach NE ein. Syenogranit und Leukogranit bilden größere Körper und weisen eine steile, nach NE einfallende, submagmatische Foliation auf. Innerhalb der (Syeno)granite weisen kristallplastische Verformung und Rekristallisation von Feldspat sowie vorhandene S-C Gefüge auf eine Deformation im Subsolidusbereich, d.h. während der Abkühlung, hin. Die aus den Mikrogefügen abgeleiteten Deformationsmechanismen charakteristischer Minerale der Quarz-Diorite und Granodiorite deuten hingegen auf Verformung unter Bedingungen einer hoch- und niedriggradigen Metamorphose hin. Innerhalb NE-SW verlaufender Mylonite am Kontakt BC/BP wird ein dextraler Schersinn durch S-C Gefüge angezeigt. In den zentralen Bereichen des BC sind Überprägungen sinistraler durch dextrale Scherzonen hingegen nur lokal sichtbar. Die Phengit-Zusammensetzung deformierter Gesteine deutet auf Scherung bei einem Maximaldruck von ca. 4.5 kbar bei T = ca. 500 °C hin. Die östlichen Nebengesteine des BC in der Region von Maham sind Migmatite, deren subhorizontale Foliation in zunehmendem Maße in wenige cm bis einige m mächtige ENE-WSW streichende Scherzonen übergeht. Die Gefüge der Migmatite der Region von Maham und (grano)dioritischer Gesteine des BC deuten auf eine regionale Überschiebungstektonik mit SSE gerichtetem Deckentransport hin. Die Zirkon- und Monazitalter deuten auf zwei Altersgruppen innerhalb des BC hin mit jeweils unterschiedlichen Platznahmealtern. Die ältere Gruppe besteht aus Quarzdiorit (643 ±5 Ma und 641 ±4 Ma, LA-ICPMS Daten, U-Pb Zirkonalter) und Granodiorit (638 ±2 Ma, IDTIMS Daten; 641 ±8 Ma und 641 ±2 Ma, LA-ICPMS Daten; U-Pb Zirkonalter), die jüngere Gruppe umfasst Syenogranit (598 ±21 Ma, 605 ±11 Ma, EMP Daten, U-Th-Pb Monazitalter) und Leukogranit (607 ±3 Ma und 603 ±4 Ma, LA-ICPMS Daten; U-Pb Zirkonalter). 206Pb/238U Alter zwischen 656 ±9 Ma und 718 ±13 Ma wurden an Zirkonkernen des Granodiorits bestimmt. Eine Regressionsgerade durch alle analysierten Kerne ergibt ein oberes Schnittpunktalter von 672 ±8 Ma. Der CC wird von im m-Maßstab wechselnden Lagen dioritischer und granitischer Zusammensetzung aufgebaut. Eine mylonitische Foliation streicht NE-SW. S-L-gefüge und Quarz-[c]-Achsen Verteilungen weisen auf Plättung unter hochgradigen Bedingungen (T = 650 °C) hin. Phengit-Barometrie mylonitisierter Granite ergibt einen Maximaldruck von 6 kbar bei T = ca. 500°C. Radiometrische Untersuchungen des mylonitischen Granits des CC wurden mittels LAICPMS an Zirkon und Monazit sowie mit Elektronenstrahlmikrosonde (EMP) an Monazit durchgeführt. Das EMP Monazit Alter (621 ±33 Ma) und LA-ICPMS Alter (622 ±13, oberes Schnittpunktalter; 611 ±4 und 608 ±6 Ma, gewichtete Mittelwerte der 208Pb/232Th und 207Pb/238U Alter) stehen im Einklang mit dem konkordanten LA-ICPMS Zirkonalter (611 ±5 Ma). Letzteres wird als Intrusionsalter des Granits interpretiert. Der BP wird im Wesentlichen von mittel- bis grobkörnigem Syenogranit aufgebaut. Speziell im Randbereich werden magmatische Gefüge (Fließgefüge, Aggregate von xenomorphem Quarz) durch submagmatische Gefüge überprägt und schließlich ersetzt (kristallplastische Deformation und Rekristallisation von Quarz und Feldspat, Bildung von Myrmekiten und S-C Gefügen). Sowohl die vom magmatischen bis in das Subsolidus-Stadium anhaltende Deformation, als auch die Parallelität der steil einfallenden postmagmatischen Foliation im Randbereich des BP und den angrenzenden BC, CC und MCF weisen auf eine synkinematische Platznahme des BP entlang krustaler Blattverschiebungen hin. Ein Konkordiaalter von 602 ±1.4 Ma wurde mit der ID-TIMS Methode erhalten. Mittels LAICPMS wurde ein Alter von 599 ±13 Ma (oberes Schnittpunktalter) bestimmt, welches im Fehler dem ID-TIMS Konkordia-Alter gleicht. Letzteres wird als Platznahmealter interpretiert. Die Kombination geochronologischer und struktureller Daten erlaubt die Unterscheidung von insgesamt drei tektono-magmatischen Abschnitten: Phase I ist durch die Platznahme dioritischer und granodioritischer Gesteine des BC sowie der Protolithe der Migmatite des MCF bei etwa 640 Ma charakterisiert. Während Phase II bei ca. 607 Ma intrudierten Syenogranit und Leukogranite in den BC und der Granits des CC. Gleichzeitig unterlagen die 640 Ma alten Granite einer hochgradigen Metamorphose. Die Intrusion der 607 Ma alten Plutonite geht einher mit einem Wechsel von Überschiebungstektonik hin zu sinistraler Blatterverschiebungstektonik. Die Platznahme des porphyritischen Syenogranits von Batié vor ca. 600 Ma, welche dextrale Bewegungen im Randbereich des BP und unmittelbar angrenzender Nebengesteine auslöste, stellt die dritte tektono-magmatische Phase dar. Alter von 700 bis 660 Ma, bestimmt an Zirkonkernen der Migmatite des MCF und der Granodiorite des BC, indizieren eine Platznahme der ältesten Granite in Pan-Afrikanischem Basement. Einige ererbte Zirkonkerne paläoproterozoischen Alters innerhalb des Leukogranits des BC deuten auf die Beteiligung Eburnischer Kruste in der Entwicklung der Pan-Afrikanischen Granite hin. Die neuen Daten bestätigen bisherige Vermutungen, dass der westliche NFBC ein afrikanisches Äquivalent zur Borborema Provinz Brasiliens darstellt. Auffällig sind geochronologische Übereinstimmungen bei den (Meta)granitoiden und den prä- bis synkinematischen Brasiliano Granitoiden der Borborema Provinz. Auf der anderen Seite ist speziell in der späten Entwicklung ab ca. 600 Ma die Kinematik blattverschiebender Bewegungen teilweise unterschiedlich. Eine mögliche Ursache sind lokale Variationen im Stressfeld, bedingt durch die Platznahme der syn- bis spät-tektonischen Magmatite.
This thesis deals with the analysis of “presolar” silicates and oxides by high resolution mass spectrometry and electron microscopy techniques. This “stardust” was identified by its extreme oxygen isotopic anomalies, which point to nucleosynthetic reactions in stellar interiors, in the carbonaceous chondrite Acfer 094. Isotopic, chemical and mineralogical studies on these stardust grains therefore allow the testing of astrophysical questions on Earth, which are otherwise only accessible by spectroscopy and theoretical models. The class of presolar silicates has been identified only six years ago in 2002, although it was known already from spectroscopic observations that silicates represent the most abundant type of dust in the galaxy. The development of the “NanoSIMS” was a crucial step in this respect, because this ion probe with its superior spatial resolution of only 50 nm allowed the detection of the typically 300 nm sized presolar silicates. A total of 142 presolar silicates and 20 presolar oxides were identified within Acfer 094, whose matrix therefore contains 163 ± 14 ppm presolar silicates and 26 ± 6 ppm presolar oxides. This is among the highest amounts reported so far for any primitive solar system material. The majority of detected stardust grains derive from asymptotic giant branch stars of 1 – 2.5 Msun and close-to-solar or slightly lower-than-solar metallicity. However, by measuring the Si isotopic compositions of some enigmatic grains, it could be shown that there is a sub-class of presolar silicates characterized by an extreme enrichment of 17O and a moderate enhancement of 30Si relative to solar, whose origins might be explained by formation in binary stellar systems. About 10% of all grains exhibit an enrichment in 18O and some of them also of 28Si relative to solar, which most likely point to an origin in type II supernova explosions. The Si isotopic measurements also allowed to quantify the effect of the s-process on the Si isotopes in low-mass asymptotic giant branch stars. The results agree well with theoretical predictions. The grains were furthermore characterized by SEM and the chemistries of about half of the grains were determined by Auger electron spectroscopy. The majority of grain morphologies are consistent with what is expected from condensation experiments. However, a lot of grains are altered by Fe-rich minerals, which are either of primary condensation or of secondary ISM or solar nebula origin. Furthermore, complex presolar grains consisting of refractory Al-rich grains attached to silicate material could be identified, which have been predicted by condensation theory and observational evidence. Nine presolar silicates were analyzed by combined NanoSIMS/TEM studies. The majority of grains are Mg-rich and amorphous, which is in contrast to astrophysical evidence, which mainly postulate crystalline Mg-rich and amorphous Fe-rich circumstellar condensates. However, the grains might have been rendered amorphous by secondary processes in the ISM or could have condensed under non-equilibrium, low-temperature conditions in the circumstellar outflow. The grains are more likely characterized by a variable, pyroxene-like chemistry, which could be a result of sputtering in the ISM, which preferentially removes Mg. The detected crystalline presolar silicates in this study and in other work are all olivines, whereas grains with a pyroxene stoichiometry are all amorphous except one. This supports astrophysical models which point to different formation pathways for these two types of grains and therefore different crystallinity. However, the relatively high Fe content of three detected presolar olivines in this study and in other work is in contrast to astrophysical evidence and theoretical considerations, which predict essentially Fe-free crystalline grains. It is therefore possible that the infrared spectra might also be compatible with less Mg-rich olivines. The only crystalline presolar silicate with a pyroxene-like stoichiometry is the unusual grain 1_07: although it is chemically enstatite, the electron diffraction pattern could only be indexed to silicate perovskite, which is stable above ~23 GPa. The discovery of a high-pressure phase of presolar origin shows that dust grains encountering interstellar shocks might not necessarily be completely destroyed. In astrophysical models it is in principle also possible that a fraction of larger grains might survive such a shock wave encounter as a high-pressure modification, which is supported by this discovery.
The present study was elaborated within the scope of the INTAFERE (Integrated Analysis of Mobile Organic Foreign Substances in Rivers) project which investigates the occurrence of xenobiotics in small freshwater streams with particular consideration of social impact factors. The aim of this study is to investigate the seasonal and spatial variance of organic micropollutants in small fresh water streams and to identify possible sources and sinks. Therefore four small freshwater river systems in Hesse, Germany, have been investigated with respect to common organic pollutants such as: the organophosphates tri-n-butyl phosphate (TBP), tris(2-butoxyethyl)phosphate (TBEP), tris(2-chloroethyl)phosphate (TCEP), tris(1-chloro-2-propyl)phosphate (TCPP), and tris(1,3-dichloro-2-propyl)phosphate (TDCPP), the synthetic musk fragrances 1,3,4,6,7,8-hexahydro-4,6,6,7,8,8-hexa-methylcyclopenta-[g]-2-benzopyran (HHCB) and 7-acetyl-1,1,3,4,4,6-hexamethyl-1,2,3,4-tetrahydronaphthalene (AHTN), the endocrine disruptors bisphenol A (BPA), 4-tert-octylphenol (OP) and the technical isomer mixture of 4-nonylphenol (NP), the herbicide terbutryn [2-(t-butylamino)-4-(ethylamino)-6-(methylthio)-s-triazine] as well as the insect repellent N,N-diethyl-m-toluamide (DEET). Water samples were collected in the time span from September 2003 to September 2006 at 26 sampling locations. The samples were extracted with solid phase extraction (SPE) and analyzed by coupled gas chromatography-mass spectrometry (GC-MS). For quantification the internal standard method was used. The results of the study showed an ubiquitous occurrence of organic pollutants in the fresh water streams of the study area. The organophosphates have been detected in 90 % of the water samples with mean concentrations of 502 ng/l (TCPP), 276 ng/l (TBP), 183 ng/l (TBEP), 118 ng/l (TCEP) and 117 ng/l (TDCPP). Sewage treatment plant (STP) effluents were identified as the dominating source for the chlorinated organophosphates as well as for the synthetic musk fragrances and the insect repellent DEET in the river systems. Consequently the highest concentrations were observed in the Schwarzbach system characterized by the highest proportion of waste water compared to the other river systems. Mean concentration levels of the synthetic musk fragrances HHCB and ATHN were 141 ng/l and 46 ng/l, respectively and 124 ng/l in case of DEET. The synthetic musk fragrances showed a clear seasonal trend with significantly lower concentrations in summer times compared to winter times, which is ascribed to stronger photodegradation and volatization during summer times. In contrast, mean DEET concentrations and loads were significantly higher in summer than in autumn, winter and spring, in parallel with the main insect season. The concentrations of the endocrine disruptors BPA, NP and OP in the river water samples ranged from <20 ng/l to 1927 ng/l, <10 ng/l to 770 ng/l, and <10 ng/l to 420 ng/l, respectively. Whereas OP was present in about 2/3 of the samples, NP and BPA could only be detected in 56% and 13% of the water samples, respectively. BPA levels exceeded in two samples the predicted no-effect concentration (PNEC) for water organisms. In case of NP, highest concentrations and loads were found in September 2003 and decreased significantly since then. In contrast, concentrations and loads of OP which serves in a similar application field remained nearly constant during the sampling period. The decrease of NP can be attributed to the implementation of the European Directive 2003/53/EG, which restricts the use of nonylphenols and nonylphenol ethoxylates since January 2005. However, at the end of the sampling period in September 2006, NP could still be detected at mean concentrations of 18 ng/l in the river waters of the sampling area. Furthermore, absence of NP in several samples from associated STP effluents indicate that the STPs cannot be the only sources for NP found in the river water. The herbicide terbutryn was present in the rivers during the whole sampling period from September 2003 to September 2006 despite a ban on its use as a herbicide from January 2004 on. Terbutryn levels ranged from < 4 ng/l to 5600 ng/l, showing a clear spatial pattern with high terbutryn concentrations in the Weschnitz and Modau river systems and significantly lower terbutryn levels in Schwarzbach and Winkelbach. Results from the analysis of two STP effluents discharging into the Weschnitz and the Modau, respectively, indicate that terbutryn enters the rivers from this source. Furthermore, terbutryn concentrations and loads showed a clear seasonal trend with significantly higher levels in summer and autumn. Obviously, the ban on agricultural use of terbutryn at the end of 2003 had no discernable influence on terbutryn concentration in the rivers because there was no trend of decreasing.