Refine
Document Type
- Conference Proceeding (2)
- Doctoral Thesis (1)
Has Fulltext
- yes (3)
Is part of the Bibliography
- no (3)
Keywords
- Abbremsen (1)
- Darmstadt / Gesellschaft für Schwerionenforschung (1)
- Detektorentwicklung (1)
- Diamantdetektor (1)
- Emittanz (1)
- Emittanzmessung (1)
- HITRAP (1)
- Ionenstrahl (1)
- Optische Messung (1)
- Pepperpot-Messung (1)
Institute
- Physik (3)
The HITRAP linear decelerator currently being set up at GSI will provide slow, few keV/u highly charged ions for atomic physics experiments. The expected beam intensity is up to 105 ions per shot. To optimize phase and amplitude of the RF systems intensity, bunch length and kinetic energy of the particles need to be monitored. The bunch length that we need to fit is about 2 ns, which is typically measured by capacitive pickups. However, they do not work for the low beam intensities that we face. We investigated the bunch length with a fast CVD diamond detector working in single particle counting mode. Averaging over 8 shots yields a clear, regular picture of the bunched beam. Energy measurements by capacitive pickups are limited by the presence of intense primary and partially decelerated beam and hence make tuning of the IH-structure impossible. The energy of the decelerated fraction of the beam behind the first deceleration cavity was determined to about 10 % accuracy with a permanent dipole magnet combined with a MCP. Better detector calibration should help reaching the required 1%. Design of the detectors as well as the results of the measurements will be presented.
Intense ion beams with small phase space occupation (high brilliance) are mandatory to keep beam losses low in high current injector accelerators like those planned for FAIR. The low energy beam transport from the ion source towards the linac has to keep the emittance growth low and has to support the optimization of the ion source tune. The Frankfurt Neutron Source Facility FRANZ is currently under construction. An intense beam of protons (2 MeV, 200 mA) will be used for neutron production using the Li7(p,n)Be7 reaction for studies of the astrophysical s-process. A collimation channel, which can be adjusted to allow the transport of beams with a certain beam emittance, is an ideal tool to optimize the ion source tune in terms of beam brightness. Therefore a collimation channel in the Low Energy Beam Transport section will be used. Through defined apertures and transversal phase space rotation using focusing solenoids the beam halo as well as unwanted H2+ and H3+ fractions will be cut. Theoretical studies which were carried out so far and a first design of the setup will be presented.
Bei der GSI – Helmholtzzentrum für Schwerionenforschung in Darmstadt wird im Rahmen des HITRAP-Projekts ein linearer Abbremser für schwere, hochgeladene Ionen für atomphysikalische Präzisionsexperimente in Betrieb genommen. Während der Inbetriebnahme wurden transversale Emittanzmessungen mit der Pepperpot- und der Multi-Gradienten-Methode durchgeführt, um die Emittanz des aus dem Experimentierspeicherring (ESR) extrahierten Strahls zu messen. Weiterhin wurde auch die Phasenraumverteilung des auf eine Zwischenenergie von 500keV/u abgebremsten Strahls hinter der IH-Struktur gemessen. Dazu wurden neue Auswertealgorithmen in die Analyse der digitalen Bilder integriert. Die longitudinalen Bunchstrukturmessungen des Strahls am Eintrittspunkt in den Abbremser und die Funktionsweise des Doppel-Drift Bunchers wird gezeigt. Die Konzeption und der Aufbau sowie die erste Inbetriebnahme einer neuartigen Einzelschuss-Pepperpot-Emittanzmessanlage für kleinste Strahlströme und -energien wird beschrieben, die es ermöglichen, den Strahl hinter den Abbremskavitäten zu vermessen. Zusätzlich wurden transversale Strahldynamikrechnungen durchgeführt, welche theoretische Grundlagen zur Inbetriebnahme von HITRAP lieferten. Es wird beschrieben, wie die gesamte Strahllinie vom ESR bis zum Radio-Frequenz Quadrupol nach der erfolgreichen Integration einer Abbremsroutine innerhalb des Softwarepakets COSY Infinity optimiert werden kann.