Refine
Year of publication
Document Type
- Doctoral Thesis (593) (remove)
Has Fulltext
- yes (593)
Is part of the Bibliography
- no (593) (remove)
Keywords
- Quark-Gluon-Plasma (8)
- Schwerionenphysik (8)
- CERN (5)
- Heavy Ion Collisions (5)
- Ionenstrahl (5)
- LHC (5)
- Monte-Carlo-Simulation (5)
- Quantenchromodynamik (5)
- Schwerionenstoß (5)
- Teilchenbeschleuniger (5)
Institute
- Physik (593) (remove)
The PhD addresses the feasibility of reconstructing open charm mesons with the Compressed Baryonic Matter experiment, which will be installed at the FAIR accelerator complex at Darmstadt/Germany. The measurements will be carried out by means of a dedicated Micro Vertex Detector (MVD), which will be equipped with CMOS Monolithic Active Pixel Sensors (MAPS). The feasibility of reconstructing the particles with a proposed detector setup was studied.
To obtain conclusive results, the properties of a MAPS prototype were measured in a beam test at the CERN-SPS accelerator. Based on the results achieved, a dedicated simulation software for the sensors was developed and implemented into the software framework of CBM (CBMRoot). Simulations on the reconstruction of D0-mesons were carried out. It is concluded that the reconstruction of those particles is possible.
The PhD introduces the physics motivation of doing open charm measurements, represents the results of the measurements of MAPS and introduces the innovative simulation model for those sensors as much as the concept and results of simulations of the D0 reconstruction.
Der Radiofrequenzquadrupol (RFQ) wird typischerweise als erstes beschleunigendes Element in Beschleunigeranlagen eingesetzt. Das elektrische Quadrupolfeld ermöglicht die gleichzeitige Fokussierung und Beschleunigung des Ionenstrahls. Zudem ist der RFQ in der Lage den Gleichstromstrahl von der Ionenquelle zu Teilchenpaketen (Bunche) zu formen, die von den nachfolgenden Driftröhrenbeschleunigern benötigt werden. Ziel der vorliegenden Arbeit war die Untersuchung zur Realisierbarkeit eines 325 MHz 4-rod RFQ Beschleunigers. Die Frequenz von 325 MHz stellt eine ungewöhnlich hohe Betriebsfrequenz für die 4-rod Struktur dar und wird z.B. für den Protonenlinac des FAIR Projektes benötigt. Ein Problem hierbei war, dass durch die bauartbedingten unsymmetrischen Elektrodenaufhängung und der hohen Frequenz ein, das Quadrupolfeld überlagerndes, Dipolfeld erzeugt wird. Dieses störende Feld kann z.B. zu einem Versatz der Strahlachse führen. Hierzu wurde die 4-rod Struktur in Simulationen grundlegend auf Einflüsse von verschiedenen Parametern auf die Resonanzfrequenz und das Dipolfeld untersucht. Es wurden Lösungsstrategien erarbeitet das Diopolfeld zu kompensieren und auf einen Prototypen angewendet. Zudem wurde das Verhalten höherer Schwingungsmoden dieser Struktur simuliert. In diesem Rahmen wurden auch Simulationen zu Randfeldern zwischen den 4-rod Elektroden und der Tankwand untersucht, um nachteilige Effekte für die Strahlqualität auszuschließen. Basierend auf den Simulationsergebnissen wurde ein Prototyp angefertigt. Dieser Prototyp wurde zur Demonstration der Betriebseigenschaften mit Leistungen bis 40 kW getestet. Hierbei wurde die Elektrodenspannung mittels Gammaspektroskopie bestimmt und daraus die Shuntimpedanz berechnet. Diese Werte wurden mit anderen Methoden der Shuntimpedanzbes- timmung verglichen. Außerdem wurden alternative RFQ Resonatorkonzepte ebenfalls auf ihre Realisierbarkeit für den Protonenlinac untersucht. Die Einflüsse verschiedener Parameter auf die Betriebsfrequenz, die Möglichkeiten des Frequenztunings und der Einstellung der longitudinalen Spannungsverteilung gefertigter Modelle wurden in einer Diskussion gegenübergestellt.
Die vorliegende Arbeit befasste sich mit der Entwicklung und der Aufbau einer neuartigen Fingerdriftröhren-Struktur als Teil des neuen Vorbeschleunigers COSY-SCL am Kernforschungszentrum in Jülich. In dieser Arbeit wird die Entwicklung der Spiralresonatoren beschrieben, die als Nachbeschleuniger direkt hinter den RFQs zum Einsatz kommen sollen. Als mögliche Option zur Verbesserung der Strahlqualität wurden Fingerdriftröhren vorgeschlagen. Mit Hilfe dieser Struktur ist es möglich, mit geringer zusätzlicher Leistung eine Fokussierung des Ionenstrahls in der beschleunigenden Struktur zu erreichen. Dies war bisher nur bei niedrigen Energien mit der RFQ-Struktur möglich. Bei höheren Energien ist man stets auf magnetische Quadrupollinsen angewiesen. Dies führt jedoch gerade in einem Geschwindigkeitsbereich bis ca. 10 % der Lichtgeschwindigkeit zu Problemen, da die zur Verfügung stehenden Abmessungen zu gering sind. Nachdem zunächst das COSY-SCL Projekt vorgestellt wurde und die grundlegende Theorie für RFQ und Driftröhrenbeschleuniger behandelt wurde, wurden in Kapitel 5 Rechnungen zur Strahldynamik mit dem Programm RFQSIM vorgestellt. Aufgrund der hohen benötigten Gesamtspannung fiel die Entscheidung, einen Vierspaltresonator mit einer geerdeten Mitteldriftröhre aufzubauen. Durch diese Veränderung wurde es möglich, die Feldstärken in den einzelnen Spalten gleichmäßiger zu verteilen und niedriger zu halten, und die benötigte Verlustleistung zu minimieren. Die Teilchendynamik in einem Beschleunigungsspalt mit Fingerelektroden wurde mit einem neuen Transportmodul in RFQSIM untersucht, das den Transport geladener Teilchen durch beliebige dreidimensionale Elektrodenkonfiguration ermöglicht. Mit Hilfe der Fingerdriftröhren ist es möglich, die transversale Ausdehnung des Strahls am Ausgang des Nachbeschleunigers zu verringern und die Anpassung an einen folgenden Beschleuniger zu vereinfachen, ohne das große Einbußen bezüglich der Effektivität der Beschleunigung in Kauf genommen werden müssen. Um die HF Eigenschaften der beiden Beschleunigerstrukturen zu vergleichen, wurden sie mit dem MWS Programm numerisch berechnet. Um genauere Aussagen über die Eigenschaften des elektrischen Feldes zu machen, wurde eine Multipolanalyse der Felder durchgeführt. Damit lässt sich eine Aussage über die Stärke der Fokussierung und mögliche Feldfehler machen. Dabei zeigte sich, dass die auftretenden Feldfehler vernachlässigbar klein sind und sogar störende Effekte unterdrückt werden. Abschließend wurde der Aufbau des Resonators und den daran durchgeführten Messungen auf Meßsenderniveau behandelt. Resultat dieser Untersuchungen ist eine Struktur, die sehr gut und effektiv als Nachbeschleuniger hinter dem RFQ für COSY-SCL eingesetzt werden kann. Durch den Einsatz der Fingerdriftröhren kann mit einer einzelnen Struktur sowohl die Aufgabe der Beschleunigung als auch der Fokussierung bei mittleren Teilchenenergien bewältigt werden. Der neue fokussierende Spiralresonator entspricht in seinen Eigenschaften einer RFQ-Struktur für höhere Teilchengeschwindigkeiten. Die Ergebnisse dieser Arbeit zeigen, wie attraktiv eine solche Lösung mit Fingerdriftröhren ist. Deshalb ist geplant, in einem nächsten Schritt Strahltests durchzuführen, da die beschriebene Driftröhrenstruktur mit ihren Eigenschaften sehr gut für die Beschleunigung von Ionen in dem Geschwindigkeitsbereich zwischen RFQ- und IH Struktur geeignet ist und ein Einsatz z.B. in dem FLAIR Projekt möglich wäre.
Resistive Plate Chambers (RPCs) are gaseous parallel plate avalanche detectors that implement electrodes made from a material with a high volume resistivity between 10 high 7 and 10 high 12 omega cm. Large area RPCs with 2mm single gaps operated in avalanche mode provide above 98% efficiency and a time resolution of around 1 ns up to a flux of several kHz/cm high 2. These Trigger RPCs will, as an example, equip the muon detector system of the ATLAS experiment at CERN on an area of 3650 m high 2 and with 355.000 independent read out channels. Timing RPCs with a gas gap of 0.2 to 0.3mm are widely used in multi gap configurations and provide 99% efficiency and time resolution down to 50 ps. While their performance is comparable to existing scintillator-based Time-Of-Flight (TOF) technology, Timing RPCs feature a significantly, up to an order of magnitude, lower price per channel. They will for example equip the 176 m high 2 TOF barrel of the ALICE experiment at CERN with 160.000 independent read out cells. RPCs were originally operated in streamer mode providing large signals which simplifies readout electronics and gap uniformity requirements. However, high rate applications and detector aging issues made the operation in avalanche mode popular. This was also facilitated by the development of new highly quenching C2F4H2-based gas mixtures with small contents of SF6. While the physics of streamers is difficult to study, the avalanche mode opened the possibility for a detailed simulation of the detector physics processes in RPCs. Even though RPCs were introduced in the early eighties and have been (will be) used in experiments, there are still disagreements about the explanation of several aspects of the RPC performance. The high efficiency of single gap RPCs would require a large ionization density of the used gases, which according to some authors contradicts measurements. Even in the case of a large ionization density the gas gain has to be extremely large, in order to arrive at the observed RPC efficiency. This raises other questions: A very strong space charge effect is required to explain the observed small avalanche charges around 1 pC. Doubts have been raised whether an avalanche can progress under such extreme conditions without developing into a streamer. To overcome these difficulties, other processes, like the emission of an electron from the cathode, were suggested. Moreover, the shape of measured charge spectra of single gap RPCs differs largely from what is expected from the statistics of the primary ionization and the avalanche multiplication. In this thesis we discuss the detector physics processes of RPCs, from the primary ionization and the avalanche statistics to the signal induction and the read out electronics. We present Monte-Carlo simulation procedures that implement the described processes. While the fundament of the described model and some results were already published elsewhere [1], the subject of this thesis is the implementation of the space charge effect. We present analytic formulas for the electrostatic potential of a point charge in the gas gap of an RPC. These formulas were developed in collaboration with the University of Graz [2] and were published in [3, 4]. The simulation model presented in [1] is completed by the dynamic calculation of the space charge field using these formulas. Since the gas parameters like drift velocity and the Townsend and attachment coefficients depend on the electric field, they are calculated dynamically as well. The functional dependence of these parameters on the field is obtained with the simulation programs MAGBOLTZ and IMONTE. For the primary ionization parameters, we use the values that are predicted by the program HEED. While the described procedure only simulates the longitudinal avalanche development towards the anode of the RPC, we also present more dimensional models that allow a careful study of the transverse repulsive and attractive forces of the space charge fields, and of the consequences for the avalanche propagation. We shall show that the efficiencies of single gap Timing RPCs is indeed explained by the high primary ionization density (about 9.5 /cm as predicted by HEED) and a large effective Townsend coefficient (around 113 /mm as predicted by IMONTE). We show that the space charge field reaches the same magnitude as the applied electric field in avalanches at large gas gain. This strong space charge effect effectively suppresses large values for the avalanche charges. The shape of the simulated charge spectra is very similar to the measurements. Also the simulated average charges are close to the experimental results. RPCs are operated in a strong space charge regime over a large range of applied voltage, contrary to wire chambers. We apply only standard detector physics simulations to RPCs. The performance of Timing and Trigger RPCs is well reproduced by our simulations. The results concerning the space charge effect were presented and discussed at the 'RPC 2001' workshop [5] and on the '2002 NSS/MIC' conference [6].
Determination of the structure of complex I of Yarrowia lipolytica by single particle analysis
(2004)
Komplex I enthält ein Flavinmononukleotid sowie mindestens acht Eisen- Schwefel Zentren als redoxaktive Cofaktoren. Da ein wesentlicher Teil des mitochondrialen Genoms für Untereinheiten von Komplex I codiert, betrifft eine Vielzahl von mitochondrialen Erkrankungen diesen Enzymkomplex.
Komplex I wurde bisher aus Mitochondrien, Chloroplasten und Bakterien isoliert. Die Minimalform von Komplex I wird in Bakterien gefunden, wo er aus 14 (bzw 13 im Falle einer Genfusion) Untereinheiten besteht und eine Masse von etwa 550 kDa aufweist. Generell werden sieben hydrophile und sieben hydrophobe Untereinheiten mit über 50 vorhergesagten Transmembranhelices gefunden. Im Komplex I aus Eukaryoten wurde eine grössere Anzahl zusätzlicher, akzessorischer Untereinheiten nachgewiesen. Hier werden die sieben hydrophoben Untereinheiten vom mitochondrialen Genom codiert, während alle anderen Untereinheiten kerncodiert sind und in das Mitochondrium importiert werden müssen.
Die obligat aerobe Hefe Yarrowia lipolytica wurde als Modellsystem zur Untersuchung von eukaryotischem Komplex I etabliert. Die bisher am besten untersuchte Hefe Saccharomyces cerevisiae enthält keinen Komplex I. Hier wird die Oxidation von NADH durch eine andere Klasse von sogenannten alternativen NADH Dehydrogenasen durchgeführt. Auch Y. lipolytica enthält ein solches alternatives Enzym, das allerdings mit seiner Substratbindungsstelle zur Aussenseite der inneren Mitochondrienmembran orientiert ist. Durch molekularbiologische Manipulation konnte eine interne Version dieses Enzymes exprimiert werden, wodurch es möglich ist, letale Defekte in Komplex I Deletionsmutanten zu kompensieren. Mittlerweile wurden alle Voraussetzungen geschaffen, um kerncodierte Untereinheiten von Komplex I aus Y. lipolytica gezielt genetisch zu verändern. Die Proteinreinigung wird durch die Verwendung einer auf einem His-tag basierenden Affinitätsreinigung erheblich erleichtert...
The PANDA experiment at FAIR will perform world class physics studies using high-intensity cooled antiproton beams with momenta between 1.5 and 15 GeV/c. A rich physics program requires very good particle identification (PID). Charged hadron PID for the barrel section of the target spectrometer has to cover the angular range of 22-140° and separate pions from kaons for momenta up to 3.5 GeV/c with a separation power of at least 3 standard deviations. The system that will provide it has to be thin and operate in a strong magnetic field. A ring imaging Cherenkov detector using the DIRC principle meets those requirements. The design of the PANDA Barrel DIRC is based on the successful BABAR DIRC counter with several important changes to improve the performance and optimize the costs. The design options are being studied in detailed Monte Carlo simulation, and implemented in increasingly complex system prototypes and tested in particle beams. Before building the full system prototypes the radiator bars and lenses are measured on the test benches. The performance of the DIRC prototype was quantified in terms of the single photon Cherenkov angle resolution and the photon yield. Results for two full system prototypes will be presented. The prototype in 2011 aimed at investigating the full size expansion volume. It was found that the resolution for this configuration is at the level of in good agreement with ray tracing simulation results. A more complex prototype, tested in 2012, provided the first experience with a compact fused silica prism expansion volume, a wide radiator plate, and several advanced lens options for the focusing system. The performance of the baseline configuration of the prototype with a standard lens and an air gap met the requirements for the PANDA PID for most of the polar angle range but failed at polar angles around 90° due to photon loss at the air gap. Measurements with a prototype high-refractive index compound lens without an air gap at a polar angle of 128° beam angle showed a good resolution of σΘC = 11.8 ± 0.7 mrad and a high photon yield of Nph = 26.1 ± 0.4. Even at polar angles close to 90° the photon yield with this lens exceeded 15 detected photons per particle, meeting the PANDA Barrel DIRC PID requirements for the entire phase space and demonstrating that the compact focusing DIRC is a very promising option for PANDA.
This dissertation presents the development of a new radio frequency quadrupole (RFQ) structure of the 4-rod type with an operating frequency of 108 MHz for the acceleration of heavy ions with mass-to-charge ratios of up to 8.5 at high duty cycles up to CW operation ("continuous wave") at the High Charge Injector (HLI) of the GSI Helmholtz Centre for Heavy Ion Research in Darmstadt.
The need to develop a completely new RFQ for the HLI arises from the fact that with the previously designed and built 4-rod RFQ structure, which was commissioned at the HLI in 2010 as part of the planned HLI upgrade program, the desired operating modes in both pulsed and CW operation could not be achieved even after several years of operating experience and considerable efforts to eliminate or at least mitigate the severe operational instabilities. Mechanical vibrations of the electrodes, which result in strong modulated power reflection, as well as the high thermal sensitivity proved to be particularly problematic.
In addition to the RF design of the new RFQ by simulations performed with the CST Microwave Studio software, the focus of the investigations fell on the mechanical analysis of vibrations on the electrode rods caused by RF operation, for which the ANSYS Workbench software was used. Due to the high thermal load of the RFQ structure of more than 30 kW/m in CW operation, an accurate analysis of the thermal effects on electrode deformation as well as resulting frequency detuning of the resonator is also required, which was investigated by simulations within the capabilities of CST Mphysics Studio.
Based on the results of the design studies carried out by simulations and the thereby achieved design optimizations, a 4-rod RFQ prototype with 6 stems was finally manufactured, on which most of the properties expected from the simulations could be validated by measurements of the RF characteristics as well as of the vibration behavior.
Finally, based on the results of the pre-tests and considering a newly developed beam dynamics concept, a completely revised RF design for a new full-length HLI-RFQ was derived from the prototype design.
Die extrem hohen Interaktionsraten, die mit dem CBM Experiment verfügbar sein werden, erlauben die Messung von einigen der herausfordensten Observablen im Feld der Schwerionenphysik. Im besonderen die Messung von Dileptonen im mittleren Massenbereich ist nahezu unmöglich für eine Vielzahl anderer Experimente, da die extrem kleinen Wirkungsquerschnitte der Produktionskanäle das Auftreten eines messbaren Ereignisses so selten machen, so dass es nicht möglich ist eine ausreichende Anzahl dieser Ereignisse zu messen. Hinzu kommt, dass speziell im Energiebereich des CBM Experiments bisher absolut keine Messdaten verfügbar sind, obwohl es zahlreiche Hinweise von theoretischer Seite und von Messungen bei größeren Kollisionsenergien darauf gibt, dass wir im Energiebereich des CBM Experiments bedeutende Entdeckungen machen k¨onnten. Eine solche Messung dieser Observable könnte einen direkten Zugang zu Informationen bezüglich eines potentiellen Phasenubergangs von hadronischer Materie (bzw. im Hadronengas) in den Zustand eines Quark-Gluonen Plasmas liefern. Zusätzlich bieten Dileptonen noch die Möglichkeit Indikatoren für eine Wiederherstellung der chiralen Symmetrie zu messen...
The development of the designs of the superconducting CH cavities of the HELIAC project from CH0 [27] to CH1 and CH2 [1] has undergone permanent improvements and adaptations based on the learned experiences of each previous cavity. For example, the design of CH1 and CH2 focused on mechanical stabilization and optimization of performance by minimizing peak electric and magnetic fields. As a result, the changes made there were already able to increase stability and performance compared to CH0 by simplifying the design in different ways. The process of designing both cavities was time reasonable, since they are identical in construction and thus only one design had to be developed. However, for both the development and manufacturing of an entire accelerator of individual CH cavities, this type of design would become too time consuming and costly. In order to reduce this time-consuming design process and accelerate the fabrication of superconducting CH cavities, and also reduce costs, a modular cavity design for mass production of superconducting CH cavities was developed as presented in this thesis. In the following section, the conclusions gained in this work and the results already presented will be summarized once again.
So in the first chapters of this thesis the theoretical foundations were laid, which are necessary for the description of superconducting cavities and for their development process, like a theoretical description of superconductivity itself (see chapter 2), the physical basics of RF-acceleration and of the CH cavity (see chapter 3), but also the effects that limit the superconducting cavities in terms of acceleration (see chapter 4) or the properties and laws from structural mechanics needed in later measurements and simulation (see chapter 5). Based on the theoretical foundations given in these sections, all measurements, evaluations and simulations made in the following sections were made.