Refine
Year of publication
Document Type
- Doctoral Thesis (29)
- Master's Thesis (3)
Has Fulltext
- yes (32)
Is part of the Bibliography
- no (32)
Keywords
- HADES (4)
- CBM (2)
- CBM Experiment (2)
- Control System (2)
- Dileptonen (2)
- EPICS (2)
- Schwerionenphysik (2)
- Spurselektion (2)
- dileptons (2)
- heavy ion physics (2)
Institute
- Physik (32)
HADES (High Acceptance DiElectron Spectrometer), located at GSI, is a versatile detector for precise spectroscopy of e+ e- pairs and charged hadrons produced on a fixed target in a 1 to 3.5 AGeV kinetic beam energy region. The main experimental goal is to investigate properties of dense nuclear matter created in heavy ion collisions and learn about in-medium hadron properties.
In the HADES set-up 24 Mini Drift Chambers (MDC) allow for track reconstruction and determining the particle momentum by exploiting charged particle deflection in a magnetic field. In addition, the drift chambers contribute to particle identification by measuring the energy loss. The read-out concept foresees each sensing wire to be equipped with a preamplifier, analog pulse shaper and discriminator. In the current front-end electronics, the ASD-8 ASIC comprises the above modules. Due to limitations of the current on-board time to digital converters (TDC), especially regarding higher reaction rates expected at the future FAIR facility (HADES at SIS-100), the electronics need to be replaced by new board featuring multi-hit TDCs. Whereas ASD-8 chips cannot be procured anymore, a promising replacement candidate is the PASTTREC ASIC, developed by JU Krakow, which was tested w.r.t. suitability for MDC read-out in a variety of set-ups and, where possible, in direct comparison to ASD-8.
The timing precision, being the most crucial performance parameter of the joint system of detector and read-out electronics, was assessed in two different set-ups, i.e. a cosmic muon tracking set-up and a beam test at the COSY accelerator at Juelich using a minimum ionizing proton beam.
The beam test results were reproduced and can thus be quantitatively explained in a three dimensional GARFIELD simulation of a HADES MDC drift cell. In particular, the simulation is able to describe the characteristic dependence of the time precision on the track position within the cell.
A circuit simulation (SPICE) was used to closely model the time development of a raw drift chamber pulse, measured as a response to X-rays from a 55 Fe source. The insights gained from this model were used for attributing realistic charge values to the time over threshold values measured with the read-out ASICs in a charge calibration set-up. Furthermore, a high-level circuit simulation of the PASTTREC shaper is implemented to serve as a demonstration of the effect of the individual shaping and tail cancellation stages which are present in both ASICs.
Within this thesis, the mechanical integration of the Micro Vertex Detector (MVD) of the Compressed Baryonic Matter (CBM) experiment is developed. The CBM experiment, which is being set up at the future FAIR facility, aims to investigate the phase diagram of strongly interacting matter in the regime of high net-baryon densities and moderate temperatures. Heavy-ion collisions at beam energies in the range of 2 to 45 AGeV, complemented by results from elementary reactions, will allow access to these conditions. The experiments conducted at LHC (CERN, Switzerland) and at RHIC (BNL, USA = does not apply within the Beam Energy Scan program) so far focus on the investigation of the phase diagram in the regime of high temperatures and vanishing net-baryon densities. The high beam intensities provided by FAIR will enable CBM to focus its experimental program on systematical studies of rare particles. Among other particle species, open charm-carrying particles are one of the most promising observables to investigate the medium created in heavy-ion collisions since their charm quarks are exposed to the medium and traverse its whole evolution. The fact that the decay particles of these rare observables are also produced abundantly in direct processes in heavy-ion collisions results in a huge combinatorial background which attributes specific requirements to the detector systems. The call for a high interaction rate leads to a cutting-edge detector system which provides an excellent spatial resolution, thin detector stations and the capability to cope with the induced radiation as well as the high rate of traversing particles and the resulting track density. The required demands are to be implemented by the MVD which will be equipped with four planar stations positioned at 50, 100, 150 and 200 mm downstream the target. The geometrical acceptance, which has to be covered with charge-sensitive material, is defined according to the requirements of CBM in the polar angle range of [2.5°; 25°]. The MVD stations have to contribute as little as possible to the overall material budget. The expected beam intensity and the vicinity close to the target require silicon detectors that provide a hardness against non-ionizing radiation of more than 10^13 n_eq/cm² and against ionizing radiation of more than 1 Mrad. In addition, the read-out time of the sensors has to be as short as possible to avoid potential ambiguities in the particle tracking caused by the pile-up of hits having emerged from different collisions. For the time being, Monolithic Active Pixel Sensors (MAPS) offer the optimal choice of technology required to address the physics program of CBM with respect to the spectroscopy of open charm and di-electrons. The geometrical properties of these sensors define the layout of the detector. To limit the multiple scattering of the produced particles inside the geometrical acceptance, the sensors and the MVD have to operate in a moderate vacuum. The sensors are thinned down to a thickness of 50 µm and, to achieve a maximum polar angle coverage, they are glued onto both sides of dedicated thin carriers. These carriers, which are made of highly thermally conductive materials such as CVD diamond or encapsulated TPG, allow efficient extraction of the power produced in the sensors. This enables their operation at temperatures well below 0 °C as suggested by corresponding radiation hardness studies. Dedicated actively cooled aluminum-based heat sinks are positioned outside of the acceptance to dissipate the heat produced by the sensors and the front-end electronics. The design of the MVD, including the realistic thicknesses of the integrated materials, has been developed and refined in the context of this thesis. It has been transformed into a unique software model which is used to simulate and further optimize the mechanical and thermal properties of the MVD, as well as in sophisticated physics simulations. The model allowed evaluation of the material budget of each individual MVD station in its geometrical acceptance. The calculated averaged material budget values stay well below the material budget target values demanded by the physics cases. The thermal management of the MVD has been simulated on the level of a quadrant of each MVD station – four identically constructed quadrants are forming an MVD station – taking into account material properties of the sensors, the glue and the sensor carrier. The temperature gradients across the pixels of a given sensor area in the direction of the rows and columns were found to be in an acceptable range of below 5 K. A temperature difference between the thermal interface area and the maximum sensor temperature of dT = 5 K on the first and a value of dT = 40 K on the fourth MVD station has been thermally simulated assuming a sensor power dissipation of 0.35 W/cm², highlighting the need to optimize the thermal interface between the involved materials as well as the power dissipation of the sensors. The feasibility of several key aspects required for the construction phase of the MVD has been investigated within the MVD Prototype project. The construction of the MVD Prototype allowed evaluation, testing and validation of the handling and the double-sided integration of ultra-thin sensors – the required working steps for their integration have been specified, evaluated and successfully established – as well as their operation in the laboratory and during a concluding in-beam test using high-energetic pions provided by the CERN-SPS. The thermal characterization of the MVD Prototype during its operation – in a temperature range from [5 °C; 25 °C], not in vacuum – confirmed the corresponding thermal simulations conducted during its design phase and substantiated the results of the thermal simulations for the design of the MVD. The aim of a material budget value of only x/X_0 ~ 0.3% for the MVD Prototype has been accomplished. Analyzing the in-beam data, the nominal sensor performance parameters were successfully reproduced, demonstrating that the proposed integration process does not impair the sensors’ performance. Moreover, no evidence of potential impact on the sensors’ performance arising from mechanical weaknesses of the MVD Prototype mechanics has been found within the analyzed data. Based on the MVD Prototype and the simulations of the material budget as well as the thermal management, this thesis evaluated the work packages, procedures and quality assurance parameters needed to set up the starting version of the MVD and addressed open questions as well as critical procedures to be studied prior to the production phase of the detector, emphasizing the evaluation of the cooling concept in vacuum and the integration of sensors in ladder structures on both sides of the quadrants of the MVD stations.
The study of meson production in proton-proton collisions in the energy range
up to one GeV above the production threshold provides valuable information about
the nature of the nucleon-nucleon interaction. Theoretical models describe the interaction
between nucleons via the exchange of mesons. In such models, different
mechanisms contribute to the production of the mesons in nucleon-nucleon collisions.
The measurement of total and differential production cross sections provide information
which can help in determining the magnitude of the various mechanisms.
Moreover, such cross section information serves as an input to the transport calculations
which describe e.g. the production of e+e− pairs in proton- and pion-induced
reactions as well as in heavy ion collisions.
In this thesis, the production of ω and η mesons in proton-proton collisions at 3.5
GeV beam energy was studied using the High Acceptance DiElectron Spectrometer
(HADES) installed at the Schwerionensynchrotron (SIS 18) at the Helmholtzzenturm
f¨ur Schwerionenforschung in Darmstadt.
About 80 000 ω mesons and 35 000 η mesons were reconstructed. Total production
cross sections of both mesons were determined. Furthermore, the collected statistics
allowed for extracting angular distributions of both mesons as well as performing
Dalitz plot studies.
The ω and η mesons were reconstructed via their decay into three pions (π+π−π0)
in the exclusive reaction pp −→ ppπ+π−π0. The charged particles were identified
via their characteristic energy loss, via the measurement of their time of flight and
momentum, or using kinematics.
The neutral pion was reconstructed using the missing mass method. A kinematic
fit was applied to improve the resolution and to select events in which a π0 was
produced.
The correction of measured yields for the effects of spectrometer acceptance was done
as a function of four variables (two invariant masses and two angles). Systematic
studies of the acceptance for different input distributions were performed.
The measured yields were normalized to the number of measured events of elastic
scattering. Systematic errors due to the methods of the data analysis and the
background subtraction were investigated.
Production angular distributions of ω and η mesons were measured. Both mesons
exhibit a slightly anisotropic angular distribution.
The Dalitz plot of ω meson production shows indications of resonant production.
However, the deviation of the distribution from the one expected by phase space
simulations is not large.
The Dalitz plot of η meson production shows a signal of the production via the
N(1535) resonance, The contribution of N(1535) to the production was quantified
to be about 47%. The angular distribution of η mesons does not show significant
differences between resonant and non resonant production.
The total production cross section of ω mesons in the reaction pp −→ ppω was
determined to be 106.5 ± 0.9 (stat) ± 7.9 (sys) [μb] where stat indicates statistical
error and sys indicates systematic error, while that of η mesons was determined to
be 136.9 ± 0.9 (stat) ± 10.1 (sys) [μb] in the reaction pp −→ ppη
The HADES (High Acceptance DiElectron Spectrometer) is an experimental
apparatus installed at the heavy-ion synchrotron SIS-18 at GSI, Darmstadt.
The main physics motivation of the HADES experiment is the measurement
of e+e− pairs in the invariant-mass range up to 1 GeV/c2 in heavy-ion collisions
as well as in pion and proton-induced reactions.
The HADES physics program is focused on in-medium properties of the light
vector mesons ρ(770), ω(783) and φ(1020), which decay with a small branching
ratio into dileptons. Dileptons are penetrating probes which allow to study
the in-medium properties of hadrons. However, in heavy-ion collisions, the
measurement of such lepton pairs is difficult because they are rare and have a
very large combinatorial background.
Recently, HADES has been upgraded with new detectors and new electronics
in order to handle higher intensity beams and reactions with heavy nuclei up
to Au.
HADES will continue for a few more years its rich physics program at its
current place at SIS-18 and then move to the upcoming international Facility
for Antiproton and Ion Research (FAIR) accelerator complex. In this context
the physics results presented in this work are important prerequisites for the investigation
of in-medium vector meson properties in p + A and A+A collisions.
This work consists of five chapters. The first chapter introduces the physics
motivation and a review of recent physics results. In the second chapter, the
HADES spectrometer is described and its sub-detectors are presented. Chapter
three deals with the issue of lepton identification and the reconstruction of
the dielectron spectra in p + p collisions is presented. Here, two reactions
are characterized: inclusive and exclusive dilepton production reactions. From
the spectra obtained, the corresponding cross sections are presented with the
respective statistical and systematical errors. A comparison with theoretical
models is included as well. Conclusions are given in chapter four.
The final part of this work is dedicated to the HADES upgrade, whose goal
is among others the achievement of a reliable and fast data acquisition of the
Multiwire Drift Chambers (MDCs). Chapter five presents my contribution to
this successful project during the three years of my stay at GSI.
The search for a modification of hadron properties inside nuclear matter at normal and/or high temperature and density is one of the more interesting issues of modern nuclear physics. Dilepton experiments, by providing interesting results, give insight into the properties of strong interaction and the nature of hadron mass generation. One of these research tools is the HADES spectrometer. HADES is a high acceptance dilepton spectrometer installed at the heavy-ion synchrotron (SIS) at GSI, Darmstadt. The main physics motivation of HADES is the measurement of e+e- pairs in the invariant-mass range up to 1 GeV/c2 in pion- and proton-induced reactions, as well as in heavy-ion collisions. The goal is to investigate the properties of the vector mesons rho, omega and of other hadrons reconstructed from e+e- decay pairs. Dileptons are penetrating probes allowing to study the in-medium properties of hadrons. However, the measurement of such dilepton pairs is difficult because of a very large background from other processes in which leptons are created. This thesis presents the analysis of the data provided by the first physic run done with the HADES spectrometer. For the first time e+e- pairs produced in C+C collisions at an incident energy of 2 GeV per nucleon have been collected with sufficient statistics. This experiment is of particular importance since it allows to address the puzzling pair excess measured by the former DLS experiment at 1.04 AGeV. The thesis consists of five chapters. The first chapter presents the physics case which is addressed in the work. In the second chapter the HADES spectrometer is introduced with the characteristic of specific detectors which are part of the spectrometer. Chapter three focusses on the issue of charged-particle identification. The fourth chapter discusses the reconstruction of the di-electron spectra in C+C collisions. In this part of the thesis a comparison with theoretical models is included as well. The conclusion and final remarks are given in chapter five.
In this thesis, the emission of protons as well as the production of Λ hyperons, Κ0S mesons and 3ΛH hypernuclei are analyzed multi-differentially as a function of transverse momentum, rapidity and centrality. Therefore, the 3.03 billion 30 % most central Ag(1.58A GeV)+Ag events recorded by HADES are used. Furthermore, the lifetimes of Λ hyperons, Κ0S mesons and 3ΛH hypernuclei are measured. The obtained 3ΛH lifetime of (253 ± 24 ± 42) ps is compatible with the lifetime of free Λ hyperons, as predicted by theoretic calculations due to its low binding energy. Finally, also the double strange Ξ– hyperons are reconstructed. Unfortunately, the fully optimized signals lie below the confidence threshold of 5σ, which is why both an production rate and an upper production limit are estimated using averaged acceptance and efficiency corrections. Never before, 3ΛH or Ξ– were successfully reconstructed and analyzed in heavy-ion collisions at such low energies. The obtained results are compared to previous measurements and put in context with world data form different energies and collision systems.
In this thesis, different physical and electrical aspects of silicon microstrip sensors and low-mass multi-line readout cables have been investigated. These silicon microstrip sensors and readout cables will be used in the Silicon Tracking System (STS) of the fixed-target heavy-ion Compressed Baryonic Matter (CBM) experiment which is under development at the upcoming Facility for Antiproton and ion Research (FAIR) in Darmstadt, Germany. The highly segmented low-mass tracking system is a central CBM detector system to resolve the high tracking densities of charged particles originating from beam-target interactions. Considering the low material budget requirement the double-sided silicon microstrip detectors have been used in several planar tracking stations. The readout electronics is planned to be installed at the periphery of the tracking stations along with the cooling system. Low-mass multi-line readout cables shall bridge the distance between the microstrip sensors and the readout electronics. The CBM running operational scenario suggests that some parts of the tracking stations are expected to be exposed to a total integrated particle fluence of the order of 1e14 neq/cm2. After 1e14 neq/cm2 the damaged modules in the tracking stations will be replaced. Thus radiation hard sensor is an important requirement for the sensors. Moreover, to cope with the high reaction rates, free-streaming (triggerless) readout electronics with online event reconstruction must be used which require high signal-to-noise (SNR) ratio (i.e., high signal efficiency, low noise contributions). Therefore, reduction in noise is a major goal of the sensor and cable development.
For better insight into the different aspects of the silicon microstrip sensors and multi-line readout cables, the simulation study has been performed using SYNOPSYS TCAD tools. 3D models of the silicon microstrip sensors and the readout cables were implemented which is motivated by the stereoscopic construction of the silicon microstrip sensors. For the evaluation of the performance of the silicon microstrip sensors in the harsh radiation environment during experimental operation, a radiation damage model has been included. It reproduces the behavior of the irradiated CBM prototype sensors. In addition to the static characteristics, the interstrip parameters relevant to understand strip isolation and cross-talk issues have been extracted. The transient simulations have been performed to estimate the charge collection performance of the irradiated sensors. The signal transmission in the readout cables has been evaluated with the finite element simulation tool RAPHAEL. Based on the performance of the front-end electronics used for early prototyping in the CBM experiment, capacitive and resistive noise contributions from the silicon microstrip sensors and multi-line readout cables have been extracted.
To validate the aforementioned simulations, numerous tests have been performed both on the multi-line readout cables and silicon microstrip sensors. Characterizations of multi-line readout cables and silicon microstrip sensors in laboratory conditions have been found to agree reasonably well with the simulations. Considering the expected radiation environment the behavior of silicon microstrip sensors have been studied especially in terms of noise and charge collection efficiency. Source-scan of the silicon microstrip sensors using 241Am is presented. In order to test a first system of detector stations including the data acquisition system, slow control and online monitoring software and for track reconstruction, in-beam tests have been performed at the COSY synchrotron of the Research Center Juelich, Germany. Further, different design parameters have been suggested to improve the sensor and readout cable design on the basis of the simulations and the measurements. Many of these parameters have been implemented in the new prototypes under production. These new prototypes will be tested in-beam by the end of 2013.
QCD matter is expected to exist in different phases, when heated to high temperatures and getting highly compressed. Each phase could be characterized by distinct properties. A way to access extreme phases of matter in the laboratory are heavy-ion collisions at (ultra-)relativistic energies. During the collision, the temperature and density is evolving and reaches a maximum temperature and density far beyond the ground state of matter. The matter properties depend on the incident collision energy. Typically, a collision is separated into three collisions stages, namely first chance collisions (I), hot and dense stage (II) and freeze-out stage (III). Out of those, the second one is of major interest, since the extreme states of matter are generated within. For this reason, the most prominent change of the hadrons is expected to appear there in. Those changes are caused by i.e. modification of the hadronic spectral function. However, to retrieve such information is complicated. Hadrons are strongly interacting particles and therefore, carry little information about the hot and dense stage. For that purpose, decays of hadrons (low-mass vector mesons) to e+e- pairs via a virtual photon, so-called dielectrons, are an ideal probe. Electrons and positrons do not interact strongly and transport the information about the hot and dense stage nearly undisturbed to the detector. Unfortunately, the production of dielectrons is suppressed by a branching ratio of ≈ 10^(-5) and requires a precise lepton identification. Nonetheless, previous experiments have extracted a dilepton signal and observed in the low-mass range an excess over the hadronic cocktail. Latter one is expected to be caused by thermal radiation induced by the medium. Up to now, experiments conducted dilepton measurements with a focus on larger collision energies and large collision systems. Measurements of dielectrons at collision energies of around 1-2A GeV were only conducted for small and medium size collision systems. HADES continued the systematic studies by a measurement of Au+Au collisions at 1.23A GeV.
The detection of dielectrons requires detectors that handle high data rates and specific detectors for a high purity lepton identification. In HADES, the strongest separation of electrons or positrons from the hadronic background is provided by a ring imaging Cherenkov detector (RICH). Its electron identification is based on Cherenkov photons, that are emitted in ring like patterns. In this work a new approach, using the time-of-flight information to preselect electrons and the reconstructed particle trajectory to estimate ring positions, is utilized to improve the lepton identification. The concept of the so-called backtracking algorithm will be explained and applied to e+e- identification in Au+Au collisions. The whole analysis chain comprises single lepton identification, pair reconstruction and correction for efficiency and acceptance losses. The final pair spectra will be presented in form of their invariant mass, pt, mt and helicity distributions. Subsequently, transport model calculations as well as results from the recently developed coarse-grained transport approach will be compared to the dielectron spectra. Moreover, the centrality dependence of the excess yield and true (not "blue-shifted") temperature of the fireball will be presented. The results will be put in context to measurements of lighter collisions systems and at higher energies.
The first measurement of the fluctuation of the kaon-to-proton ratio in relativistic heavy-ion collisions is presented. This thesis details the analysis procedure for identifying kaons and protons using the NA49 experiment at CERN-SPS and discusses the results in the context of the current state of the field.
In this thesis, the production of charged kaons and Φ mesons in Au+Au collisions at sqrt sAuAu = 2.4 GeV is studied. At this energy, all particles carrying open and hidden strangeness are produced below their respective free nucleon-nucleon threshold with the corresponding so-called excess energies: sqrt sK+ exc = -0.15 GeV, sqrt sK- exc = -0.46 GeV, sqrt sΦ exc = -0.49 GeVGeV. As a consequence, the production cross sections are very sensitive to medium effects like momentum distributions, two- or multistep collisions, and modification of the in-medium spectral distribution of the produced states [1]. K+ and K- mesons exhibit different properties in baryon dominated matter, since only K- can be resonantly absorbed by nucleons. Although strangeness exchange reactions have been proposed to be the dominant channel for K- production in the analyzed energy regime, the production yield and kinematic distributions could also be explained in smaller systems based on statistical hadronization model fits to the measured particle yields, including a canonical strangeness suppression radius RC, and taking the Φ feed-down to kaons into account [2, 3]. For the first time in central Au+Au collisions at such low energies, it is possible to reconstruct and do a multi differential analysis of K- and Φ mesons. In principle, this should be the ideal environment for strangeness exchange reactions to occur, as the particles are produced deeply sub-threshold in a large and long-living system. Therefore, it is the ultimate test to differentiate between the different sources for K- production in HIC.
In total 7.3x10exp9 of the 40% most central Au(1.23 GeV per nucleon)+Au collisions are analyzed. The data has been recorded with the High Acceptance DiElectron Spectrometer HADES located at Helmholtzzentrum für Schwerionenforschung GSI in April/May 2012. A substantially improved reconstruction method has been employed to reconstruct the hadrons with high purity in a wide phase space region.
The estimated particle multiplicities follow a clear hierarchy of the excess energy: 41.5 ± 2.1|sys protons at mid-rapidity per unit in rapidity, 11.1 ± 0.6|sys ± 0.4|extrapol π-, (3.01 ± 0.03|stat ± 0.15|sys ± 0.30|extrapól) x10 exp -2 K+, (1.94 ± 0.09|stat ± 0.10|sys ± 0.10|extrapol)x10 exp -4 K- and (0.99 ± 0.24|stat ± 0.10|sys ± 0.05|extrapol)x10 exp -4 Φ per event. The multiplicities of the strange hadrons increase more than linear with the mean number of participating nucleons hAparti, supporting the assumption that the necessary energy to overcome the elementary production threshold is accumulated in multi-particle interactions. Transport models predict such an increase, but are overestimating the measured particle yield and are not able to describe the kinematic distributions of K+ mesons perfectly. However, the best description is given by the IQMD model with a density dependent kaonnucleon potential of 40 MeV at nuclear ground state density.
The K-=K+ multiplicity ratio is constant as a function of centrality and follows with (6.45 ± 0.77)x10 exp -3 the trend of increasing with beam energy indicated from previous experiments [4]. The effective temperature of K- TK+eff = (84 ± 6) MeV is found to be systematically lower than the one of K+ TK+eff = (104 ± 1) MeV, which has also been observed by the other experiments.
The Φ=K- ratio is with a value of 0.52 ± 0.16 higher than the one obtained at higher center-of-mass energies and smaller systems. This behavior is predicted from a tuned version of the UrQMD transport model [5], when including higher mass baryonic resonances which can decay into Φ mesons and from statistical hadronization models when suppressing open strangeness canonically. The found ratio is constant as a function of centrality and results with a branching ratio of 48.9%, that ~ 25% of all measured K- originate from Φ feed-down decays. A two component PLUTO simulation, consisting of a pure thermal and a K- contribution originating from Φ decays, can fully explain the observed lower effective temperature in comparison to K+ and the shape of the measured rapidity distribution of K-. As a result, we find no indication for strangeness exchange reactions being the dominant mechanism for K- production in the SIS18 energy regime, if taking the contribution from Φ feed-down decays into account.
The hadron yields for the 20% most central collisions can be described by a statistical hadronization model fit with the chemical freeze-out temperature of Tchem = (68 ± 2) MeV and baryochemical potential of μB = (883 ± 25) MeV, which is higher than expected from previous parameterizations. The analysis of the transverse mass spectra of protons indicate a kinetic freeze-out temperature of Tkin = (70 ± 4) MeV and radial flow velocity of βr = 0.43 ± 0.01, which is in agreement with the parameters obtained from the linear dependence of the effective temperatures on the particle mass Tkin = (71.5 ± 4.2) MeV and βr = 0.28 ± 0.09.